Hot start issue but not starter motor related
Hot start issue but not starter motor related
Author
Discussion

e635815

Original Poster:

379 posts

219 months

Saturday 17th July 2010
quotequote all
My car (2000 Chimaera 500) refuses to start when hot.
The starter motor is brand new and the car equipped with the Modwise hot start kit.
After a run on the highway yesterday, I stopped for fuel and couldn't start the car again. The outside Temp. was 34°C.
Above 90°C water Temp. the starter was spinning the engine with absolutely no effect.
Between 70°C and 80°C, the engine would sputter but no start.
Below 70°C, it started at the second attempt.

This can't be the infamous hot start, can it?
If anyone can help understand how to fix this issue, I would be forever grateful.
Thanks
Philippe

daxtojeiro

743 posts

277 months

Saturday 17th July 2010
quotequote all
Coolant sensor? Worth poping a 300-500R resistor in its place when its hot and not starting to see if it then starts. Or even pop the cover off the sensor and measure its resistance when the engine is hot.
Phil

Cider Andy

1,889 posts

256 months

Saturday 17th July 2010
quotequote all
That's NOT the 'hot start' problem (that's when the starter motor doesn't operate).

Does the rev counter needle move when the engine's being cranked? If it does, the problem's either fuelling or HT related (a fuelling issue might also involve the immobiliser - does the fuel pump pressurize the system for a couple of seconds when the ignition's switched on?). If the tacho needle doesn't move, check the LT connections and, if possible, substitute a known good ignition amp. If you do this, you must bolt the replacement in place for it to work properly.

Check for a spark from the king lead then at one of the plugs. This should eliminate the rotor arm and distributor cap (or otherwise). Beyond that I'd suspect the immobiliser or even the ECU.

The truth is it could be any one of the things I've mentioned or a number of things I haven't, but they're some likely causes that are easy to check.

penno

241 posts

261 months

Saturday 17th July 2010
quotequote all
this very similar to what mine started do when the ign module started to pack in. it would run fine cold then once warm then trying to restart was a pain. eventually it didnt start from cold due to there been no spark.

they arent that expensive to try

e635815

Original Poster:

379 posts

219 months

Monday 19th July 2010
quotequote all
You really have to love those cars, right?
It hasn’t restarted yet because of an odd problem.
The starter motor works just fine but it can't spin the motor anymore.
Let me explain:
- The starter spins and the toothed wheel is propelled forward when working.
- There are no traces of wear on the tooth, either on the starter or on the wheel.
- It spins freely in the air without touching the engine wheel.

It started doing that to me on Saturday morning when it has been working fine for the past three months. The starter itself is new (4 months) and is well tightened to the bell-housing.
I have taken it off the engine to check if it operates as it should be. And it does.

From time to time, it would catch the inertia wheel and spin it for a few revolutions before dropping it again. In any case, not sufficient for the engine to start.

Have any of you already have this type of issue? Can someone point me to the light?
Thanks and regards
Philippe

Del 203

12,728 posts

280 months

Monday 19th July 2010
quotequote all
Carefully put a lump of wood on the wheel & see if it throws out under resistance

scotty_d

6,795 posts

225 months

Monday 19th July 2010
quotequote all
Try putting it in gear and get some mates to rock the car back and forward and try spinning it over carefully to free it off and see if it catch's then?.

Colin RedGriff

2,541 posts

288 months

Monday 19th July 2010
quotequote all
If its not engaging the flywheel then I would suspect that either the motor is faulty (probably not as it is only 4 months old, but possible); or there may be a problem with the solenoid feed when it's hot, preventing the solenoid from fully energising.

e635815

Original Poster:

379 posts

219 months

Tuesday 7th September 2010
quotequote all
I have managed to go down to the bottom of the issue thanks to the precious help of Eggiman Autotechnik in Switzerland near Basel.
The brand new starter motor I had bought from a well known LR parts specialist (via its internet shop) had a faulty free wheel device. Certainly due to bad parts quality, the free wheel failed and wouldn't withstand the torque when engaged on the ring. It would spin the wheel in the air though.

Eggiman took my old and new starter to rebuild one good and the motor started straight away after that.
But soon developped another fault.
It wouldn't start when hot (starter spining). After lots of swearing and messing around, I decided to replace the ignition module and since then, the issue has been cured.

I can now enjoy stopping my car for fuelling without the fear of being blocked for 20 minutes.

I bought the car the 12th of December 2009. It's been blocked in the garage by the snow until mid-March. Then it was a non starter due to a distributor issue. The mechanics who took car of the car spent the next three months trying to understand what the issue was. He eventually failed to tune the ignition which resulted in me towing the car to Switzerland to be fixed. July and August were spent fiddling around with the ignition module and the starter motor.
Now it is September and I did my first WE with the Tiv bought 10 months ago. Results....!!!