Clutch replacement...
Discussion
My clutch is slipping under hard acceleration in 2nd and 3rd so looks like it's well on the way out ... has anyone replaced their own? (and if so - is it a pig to do? I have access to a pit.) Any recommendations where to get a standard clutch for a 400HC? (Don't see any point in anything "uprated" as I'm not going to be doing any engine work on it.)
Alternatively - anyone got any recommendations for anywhere in the Salisbury (Wiltshire / Dorset) area that would be worth contacting to do the job? How much can I expect to pay?
(I did try searching but it's under maintenance.)
Cheers
Phil
Alternatively - anyone got any recommendations for anywhere in the Salisbury (Wiltshire / Dorset) area that would be worth contacting to do the job? How much can I expect to pay?
(I did try searching but it's under maintenance.)
Cheers
Phil
Two quotes I had were both around the £750 mark from TVR specialists. I sourced the parts myself and got a friendly local mechanic to do it for £200, although we did have a few problems (faulty parts supplied) which meant my poor mechanic had to do the job twice. It's not that difficult by all accounts.
Copied from another thread :
I did the clutch on a 400 myself, parts cost about £300.
That included friction and pressure plates, bearing and carrier, fork, pivot point pushrod and retaining clip, new gearbox oil, grease etc.
Check the history on my 400 for part numbers / prices and where I got them from.
I did the clutch on a 400 myself, parts cost about £300.
That included friction and pressure plates, bearing and carrier, fork, pivot point pushrod and retaining clip, new gearbox oil, grease etc.
Check the history on my 400 for part numbers / prices and where I got them from.
TVR Beaver said:
Can you do the rear engine oil seal whilst it's all out (obviously youd need to take the flywheel off also).. but may be worth it??

Are they prone to failing?
Might get a seal in case we spot a leak whilst it's out but would rather not start disturbing too much unless there's good reason.

Phil
No.. never go... until 5 miles after you've put it all back together 
they can become hard with age and miles.... do you ever get drips from your bell housing??... If it was me, I'd do it... but just check you can get to it first without lowering the sump or something... but if you can????? your choice..

they can become hard with age and miles.... do you ever get drips from your bell housing??... If it was me, I'd do it... but just check you can get to it first without lowering the sump or something... but if you can????? your choice..

TVR Beaver said:
So when you pull the prop shaft out you don't get a gob full I assume.... 
Gearbox oil is hateful stuff - got some in my hair when I was young (and still had hair) and the bloody stuff would not come out. 

I'm assuming that the advice to drain is so it doesn't gloop out too...
Phil
You unbolt the prop from the diff, but at the gearbox end its just a push fit onto a splined shaft. Many make the mistake [including myself] of unbolting at the diff, sliding the prop rearwards out of the gearbox and a small amount of oil comes out. You think to yourself, thats not too bad, only later when you unbolt everything and your lay on your back under the car, and you slide the gearbox away from the engine, and tilt the back end down slightly,
you get the entire contents of the gearbox all over yourself. Not recommended.
you get the entire contents of the gearbox all over yourself. Not recommended.I bought an AP clutch from V8 developments, £150 delivered. I also bought the uprated arm, pivot and new master cylinder to keep it all sweet.
William Street Services in Southampton charged £150 pure labour (with reciept) to install it, as I didn't fancy that one on the driveway!
Total cost for new, fitted clutch £300. Jobbed!
William Street Services in Southampton charged £150 pure labour (with reciept) to install it, as I didn't fancy that one on the driveway!
Total cost for new, fitted clutch £300. Jobbed!
Kitchski said:
I bought an AP clutch from V8 developments, £150 delivered. I also bought the uprated arm, pivot and new master cylinder to keep it all sweet.
William Street Services in Southampton charged £150 pure labour (with reciept) to install it, as I didn't fancy that one on the driveway!
Total cost for new, fitted clutch £300. Jobbed!
Dropped them an email - let's se if they're up for doing another... William Street Services in Southampton charged £150 pure labour (with reciept) to install it, as I didn't fancy that one on the driveway!
Total cost for new, fitted clutch £300. Jobbed!

Phil
Gassing Station | Chimaera | Top of Page | What's New | My Stuff






