20 to 30 hp please????
Discussion
no tks i want the power to be there all the time without destroying my engine.ahahahhow about cam,plenium etc....i live in malaysia so no much people will dare to touch this engine.tks for ur help guys looking at 250real hp.still waiting for sc power to finish my kit.just looking at some options here.
I had mine on the rolling road today , i did think it was running a tad rich and i was correct , not much i can do without a re-map which is a problem as no one local can do it so i am thinking about going after market ECU and getting my lost 15 bhp and 30ft/lb back but don’t know if the cost is really worth it?? Any idea’s
pwd95 said:
A decent laughing gas set up. 
was that a serious suggestion wyn ?
nitrous is such a sh*tty way of improving performance.
sure you get a big gain, but 5 mins later the bottle is empty and your back to square one until you can find somewhere to fill it (not to mention costs of filling too)
look at it this way, would you rather for example have
i. 300bhp per ton for 5 mins and then standard 200 bhp per ton until you have time/location/money to refill the bottle (and start the same cycle all over again)
or
ii. say 250 bhp per ton all the time
BountyHunter said:
pwd95 said:
A decent laughing gas set up. 
was that a serious suggestion wyn ?
nitrous is such a sh*tty way of improving performance.
sure you get a big gain, but 5 mins later the bottle is empty and your back to square one until you can find somewhere to fill it (not to mention costs of filling too)
look at it this way, would you rather for example have
i. 300bhp per ton for 5 mins and then standard 200 bhp per ton until you have time/location/money to refill the bottle (and start the same cycle all over again)
or
ii. say 250 bhp per ton all the time
400/ tonne will be available at the turn of a valve and flick of a switch.

I'd first get the car on a rolling road to see where I was to start with. 240-250 bhp from a 4.0 isn't that far fetched if everything is spot on (freshly rebuilt engine with a good cam etc), however you could end up spending lots without ever getting there if it isn't.
Normally after trumpets & induction kit your next steps would be 72 mm plenum (this however requires yet another smooth bore elbow to replace the one you've got), cam and ECU remap. Former posters are right though that the bang for buck ratio will be less than what you got from the trumpets and induction hoses. Cam choice may be restricted unless you have valve pockets in the pistons a la 4.0HC. Nevertheless this is still a 'sensible' level where you can get sufficient reward for a relatively modest outlay, above and beyond this things get very expensive and IMO a bit too complicated for what you get (wholesale engine management swaps etc).
Normally after trumpets & induction kit your next steps would be 72 mm plenum (this however requires yet another smooth bore elbow to replace the one you've got), cam and ECU remap. Former posters are right though that the bang for buck ratio will be less than what you got from the trumpets and induction hoses. Cam choice may be restricted unless you have valve pockets in the pistons a la 4.0HC. Nevertheless this is still a 'sensible' level where you can get sufficient reward for a relatively modest outlay, above and beyond this things get very expensive and IMO a bit too complicated for what you get (wholesale engine management swaps etc).
900T-R said:
Normally after trumpets & induction kit your next steps would be 72 mm plenum (this however requires yet another smooth bore elbow to replace the one you've got), cam and ECU remap.
72mm butterfly is not really needed unless you have 45mm inlets, & I don't think any of them will be particularly beneficial on basic 4.0 where a nice flowing finish is all that is needed rather than bigger.scotty_d said:
I had mine on the rolling road today , i did think it was running a tad rich and i was correct , not much i can do without a re-map which is a problem as no one local can do it so i am thinking about going after market ECU and getting my lost 15 bhp and 30ft/lb back but don’t know if the cost is really worth it?? Any idea’s
Assuming its running rich flat out, dont suspect the mapping at first call, as it could be down to a faulty fuel pressure requlator or AFM. The ECU cant make any fuelling corrections at full power so it blindly follows the sensor inputs. Also worth checking it has the correct chip in the ECU, as people tend to assume that a chip from a more powerfull car will give them more power, which just aint true!dbv8 said:
BountyHunter said:
pwd95 said:
A decent laughing gas set up. 
was that a serious suggestion wyn ?
nitrous is such a sh*tty way of improving performance.
sure you get a big gain, but 5 mins later the bottle is empty and your back to square one until you can find somewhere to fill it (not to mention costs of filling too)
look at it this way, would you rather for example have
i. 300bhp per ton for 5 mins and then standard 200 bhp per ton until you have time/location/money to refill the bottle (and start the same cycle all over again)
or
ii. say 250 bhp per ton all the time
400/ tonne will be available at the turn of a valve and flick of a switch.

) Bluebottle said:
dbv8 said:
BountyHunter said:
pwd95 said:
A decent laughing gas set up. 
was that a serious suggestion wyn ?
nitrous is such a sh*tty way of improving performance.
sure you get a big gain, but 5 mins later the bottle is empty and your back to square one until you can find somewhere to fill it (not to mention costs of filling too)
look at it this way, would you rather for example have
i. 300bhp per ton for 5 mins and then standard 200 bhp per ton until you have time/location/money to refill the bottle (and start the same cycle all over again)
or
ii. say 250 bhp per ton all the time
400/ tonne will be available at the turn of a valve and flick of a switch.

) I have to say budget permitting there is nothing s
tty about running a bit of laughing gas, the reality is how often do you want your car to produce max power, and the budget you have to start with, if you have an everyday car that you want a bit of fun at the weekends gas is probably the way you want you to car, most rover engines will handle 150bhp of gas realibly, to get this the cost would be around £500, plus filling the bottle when empty, 150bhp to have on tap when ever you wanted would cost from 4-5k upwards, thats a lot of bottles to fill. if you are a track day guy then i wouldnt go for gas unless you work in a hospital and get it free!
tty about running a bit of laughing gas, the reality is how often do you want your car to produce max power, and the budget you have to start with, if you have an everyday car that you want a bit of fun at the weekends gas is probably the way you want you to car, most rover engines will handle 150bhp of gas realibly, to get this the cost would be around £500, plus filling the bottle when empty, 150bhp to have on tap when ever you wanted would cost from 4-5k upwards, thats a lot of bottles to fill. if you are a track day guy then i wouldnt go for gas unless you work in a hospital and get it free!Getting an 'extra' 30 bhp out of a 400 would mean a very much wilder cam & all the intake mods with mapping on top. A laughing gas kit will give you instant hp whenever you want it. Bit of a quick fix I know but an 'extra' 30 bhp for a 400 is going to be expensive, & if OP is already waiting for an SC kit then pesonally I'd hang on for that. Get a suitable cam installed while your waiting. 

Gassing Station | Chimaera | Top of Page | What's New | My Stuff



