Coil pack location
Coil pack location
Author
Discussion

Meatball

Original Poster:

1,638 posts

241 months

Saturday 14th August 2010
quotequote all
Where have you guys fitted yours?

Does anyone know where i can get one of these http://thumbsnap.com/ZKQbiIEp (borrowed from another thread)

spend

12,581 posts

282 months

Saturday 14th August 2010
quotequote all
Ask Fordy if he'll do you a bracket - they just mount across the front of the plenum which seems to create a good angle for leads and easy to cross banks etc.

That's a cut down dizzy, explained the process somewhere on here in the last few months (maybe engines / mods). Just finished with a screw on ally cap IIRC.

SILICONE KID

14,997 posts

262 months

Saturday 14th August 2010
quotequote all
I fitted one each side then removed the dizzy and relocated the power steering tank .Made a simple bracket for the power steering tank out of one of these..simple but works








Edited by SILICONE KID on Saturday 14th August 15:36

Meatball

Original Poster:

1,638 posts

241 months

Saturday 14th August 2010
quotequote all
spend said:
Ask Fordy if he'll do you a bracket - they just mount across the front of the plenum which seems to create a good angle for leads and easy to cross banks etc..

I was thinking the same but mounted on one of these http://trigger-wheels.com/store/contents/en-uk/d11... ive seen a few positioned above the drivers side rocker cover but that means moving the power steering pot rolleyes

spend said:
That's a cut down dizzy, explained the process somewhere on here in the last few months (maybe engines / mods). Just finished with a screw on ally cap IIRC.

So what are the options other than chopping the dizzy?


Meatball

Original Poster:

1,638 posts

241 months

Saturday 14th August 2010
quotequote all
SILICONE KID said:
I fitted one each side then removed the dizzy and relocated the power steering tank .Made a simple bracket for the power steering tank out of one of these..simple but works
The second photo shows the coil pack just above the manifold - its going to get pretty hot there
Did V8D put the packs there or yourself?

spend

12,581 posts

282 months

Saturday 14th August 2010
quotequote all
Meatball said:
So what are the options other than chopping the dizzy?
Many just pull the dizzy & bung the hole.. Unfortunately not all the serps have cam retainers so effectively you have very little holding the cam in only really the chain. If you have a pre-serp you won't have an oil pump anymore hehe

Unless you are sure the cam is retained I'd always cut the dizzy down personally.

SILICONE KID

14,997 posts

262 months

Saturday 14th August 2010
quotequote all
No V8d did not do the install.The coil pack seems pritty cool ,had a good feel around and no problems up to yet ..

Meatball

Original Poster:

1,638 posts

241 months

Saturday 14th August 2010
quotequote all
spend said:
Meatball said:
So what are the options other than chopping the dizzy?
Many just pull the dizzy & bung the hole.. Unfortunately not all the serps have cam retainers so effectively you have very little holding the cam in only really the chain. If you have a pre-serp you won't have an oil pump anymore hehe

Unless you are sure the cam is retained I'd always cut the dizzy down personally.
Thats a good point, Where is the cam retainer positioned on the cam?, is it visible down the hole hehe

SILICONE KID said:
No V8d did not do the install.The coil pack seems pritty cool ,had a good feel around and no problems up to yet ..
It wasent a dig, just a question, because your packs are either side of the alternator are your ht leads crossing over each other?


Ant.

5,254 posts

312 months

Saturday 14th August 2010
quotequote all
Here's mine:-








But also see here

http://www.pistonheads.com/gassing/topic.asp?h=0&a... Packs&mid=4852

Meatball

Original Poster:

1,638 posts

241 months

Saturday 14th August 2010
quotequote all
Thanks for the link, very helpful.

Pupp

13,044 posts

303 months

Saturday 14th August 2010
quotequote all
Another possible smile




SILICONE KID

14,997 posts

262 months

Sunday 15th August 2010
quotequote all
Yes crossing over, The leads seem to be very long .I have just made a better heat shield just as a precaution. The other side is mounted above a Steve Heath heat shield .Think mine is a one off as i have two wide band lalmbda sensors , One for each bank .
Ant. You may have problems in the future .Its going to be a bit of a job to get to them and water from your screen will be pouring all over your coil packs .







Edited by SILICONE KID on Sunday 15th August 00:17


Edited by SILICONE KID on Sunday 15th August 00:28

spend

12,581 posts

282 months

Sunday 15th August 2010
quotequote all
That bonnet lip & overhang varies on the cars and models... Look very carefully at the spacings & you might see the differences wink

Johno

8,593 posts

313 months

Sunday 15th August 2010
quotequote all
SK, there's no issues with water running over the coil packs in Ant's location.

I've been running P38 coil pack fitted in same location as Ant's (supplied on bracket that fits onto inlet manifold) for 20k miles and no issues.

Easy to get too when I need too and the neatest solution IMO.

Still not sure why anyone would want to go for anything else, lot's of good work locating other coil packs etc, but what's the advantages of running Ford items or anything else for that matter over a P38 packs ? Is it just cost ? Mine was second hand and no issues so far . . .

Pink_Floyd

900 posts

252 months

Sunday 15th August 2010
quotequote all
Johno said:
SK, there's no issues with water running over the coil packs in Ant's location.
I've been running P38 coil pack fitted in same location as Ant's (supplied on bracket that fits onto inlet manifold) for 20k miles and no issues.
Easy to get too when I need too and the neatest solution IMO.
I have a set of P38 to fit next year when I intend fitting megasquirt, but did have concerns that water on the coil packs might be a problem, but good to hear that others have not had a problem.
Did wonder about making a shield so that they wouldn't get wet, do you think that there is any point.?

Meatball

Original Poster:

1,638 posts

241 months

Sunday 15th August 2010
quotequote all
Ive definatly not got the room under the mesh as the twin plenum is larger than the single throttle set up.
Some good ideas thumbup

Whilst your all here did you bother to get the crank pulley re balanced with the trigger wheel fitted?

spend

12,581 posts

282 months

Sunday 15th August 2010
quotequote all
Lot's did, lots didn't...

How accurate the external balancing is anyway is the million dollar question wink If any parts have been swapped or the like it may not even still be at the factory tolerances???

I'm pretty sure you can't see the cam retainer through the dizzy hole - its nestled behind the cam gear..

Pupp

13,044 posts

303 months

Sunday 15th August 2010
quotequote all
If you can't see the plate itself, you'd certainly be able to see the head of the top fastener directly above the cam nose...

Meatball

Original Poster:

1,638 posts

241 months

Sunday 15th August 2010
quotequote all
Thanks for the info, i think ill chop the dizzy to be sure.

2Munkys

1,228 posts

268 months

Monday 16th August 2010
quotequote all