Just bought a Chim
Discussion
Where do I start I love it!!!!!!!
I was torn between the S200 and a Chim, and im so glad I didn't buy a over grown mx-5
Power is smooth and when ever I want it all rev's
Managed to get 30 mpg from north Manchester to Surrey with solid traffic 4 hours of it, so im very pleased with that and surprised
Few issues I need some advice with, first off i have a 'clunk' when i go back on the power ) can hear when going less than 40 mph, I heard some thing about a half moon bush at the diff? Is this right?
Also today the oil pressure gauge gave up ( im praying its just the gauge )Where do i start looking? where is the switch on the engine? or do I need to find a fuse some where?
The dash is cracked ( as with most chims ive seen ) i want to remove and recover with carbon fibre, What's the quickest way to pop that out?
Throttle is stiff and hated it to begin with, now 3 days have gone by and 700 miles it doesn't bother me any more
Also been informed that its the HC model can some one tell me a quick way to prove this? compression test?
Heres some quick pictures
See you all PH Sunday rolls royce
Alex




I was torn between the S200 and a Chim, and im so glad I didn't buy a over grown mx-5
Power is smooth and when ever I want it all rev's
Managed to get 30 mpg from north Manchester to Surrey with solid traffic 4 hours of it, so im very pleased with that and surprised
Few issues I need some advice with, first off i have a 'clunk' when i go back on the power ) can hear when going less than 40 mph, I heard some thing about a half moon bush at the diff? Is this right?
Also today the oil pressure gauge gave up ( im praying its just the gauge )Where do i start looking? where is the switch on the engine? or do I need to find a fuse some where?
The dash is cracked ( as with most chims ive seen ) i want to remove and recover with carbon fibre, What's the quickest way to pop that out?
Throttle is stiff and hated it to begin with, now 3 days have gone by and 700 miles it doesn't bother me any more
Also been informed that its the HC model can some one tell me a quick way to prove this? compression test?
Heres some quick pictures
See you all PH Sunday rolls royce
Alex
Edited by Alexdaredevilz on Sunday 15th August 21:03
Great choice.
I chopped my S2000 in for a Chimaera 400 and haven't looked back. Having said that, the Honda was a rippingly good sports car, and I wouldn't like to bet between it and the Tiv around a race circuit, but ultimately it didn't have a V8!
The clonking on taking-up drive does indeed sound like a diff/diff bush snag. Mine did it a bit.
Have fun.
I chopped my S2000 in for a Chimaera 400 and haven't looked back. Having said that, the Honda was a rippingly good sports car, and I wouldn't like to bet between it and the Tiv around a race circuit, but ultimately it didn't have a V8!
The clonking on taking-up drive does indeed sound like a diff/diff bush snag. Mine did it a bit.
Have fun.
Congratulations, hope you enjoy & you must try harder if you are getting 30 mpg out of it!
It is most likely your oil sender which is easily changed from under the car about 2min job just do it quickly & you won't loose much oil, I don't have a picture to hand but if you search the forum there is plenty of threads on it.
http://www.clever-trevor.net/search-car-category.h...
second last item if thats any help.
It is most likely your oil sender which is easily changed from under the car about 2min job just do it quickly & you won't loose much oil, I don't have a picture to hand but if you search the forum there is plenty of threads on it.
http://www.clever-trevor.net/search-car-category.h...
second last item if thats any help.
Alex,
Re: Throttle stiffness.
Mine was just the same and you do get used to it, however I have significantly "lightened" the throttle by a mix of replacing the return springs on the throttle mechanism with two lighter springs
and re-lubricating the cable.
The springs are fiddly but with a bit of patience you can probably replace these with ligher duty ones with the throttle mounting bracket in place.
When the springs were off moving the accelerator pedal just felt like there was too much resistance between the inner and outer cable. I detached the cable from the engine end, tied it to the underside of the bonnet so it was vertical and then dropped 3in1 oil down it drop by drop by drop by drop, wiggling the inner cable occasionally.
This is a long job ( springs and cable, then refitting took about 3 hours ) but the cable is so much smoother now and this job is probably a whole lot easier than fitting a new inner and outer cable.
It's a case of what you get used to but I prefer the lighter pedal feel.
Re: Throttle stiffness.
Mine was just the same and you do get used to it, however I have significantly "lightened" the throttle by a mix of replacing the return springs on the throttle mechanism with two lighter springs
and re-lubricating the cable.
The springs are fiddly but with a bit of patience you can probably replace these with ligher duty ones with the throttle mounting bracket in place.
When the springs were off moving the accelerator pedal just felt like there was too much resistance between the inner and outer cable. I detached the cable from the engine end, tied it to the underside of the bonnet so it was vertical and then dropped 3in1 oil down it drop by drop by drop by drop, wiggling the inner cable occasionally.
This is a long job ( springs and cable, then refitting took about 3 hours ) but the cable is so much smoother now and this job is probably a whole lot easier than fitting a new inner and outer cable.
It's a case of what you get used to but I prefer the lighter pedal feel.
P400PLS said:
Alex,
Re: Throttle stiffness.
Mine was just the same and you do get used to it, however I have significantly "lightened" the throttle by a mix of replacing the return springs on the throttle mechanism with two lighter springs
and re-lubricating the cable.
The springs are fiddly but with a bit of patience you can probably replace these with ligher duty ones with the throttle mounting bracket in place.
When the springs were off moving the accelerator pedal just felt like there was too much resistance between the inner and outer cable. I detached the cable from the engine end, tied it to the underside of the bonnet so it was vertical and then dropped 3in1 oil down it drop by drop by drop by drop, wiggling the inner cable occasionally.
This is a long job ( springs and cable, then refitting took about 3 hours ) but the cable is so much smoother now and this job is probably a whole lot easier than fitting a new inner and outer cable.
It's a case of what you get used to but I prefer the lighter pedal feel.
With regards to oiling the throttle cable i made a cone out of blue tack stuck it to the end of the cable and filed this with oil and left it as long as it needed to drip done the whole cable.Re: Throttle stiffness.
Mine was just the same and you do get used to it, however I have significantly "lightened" the throttle by a mix of replacing the return springs on the throttle mechanism with two lighter springs
and re-lubricating the cable.
The springs are fiddly but with a bit of patience you can probably replace these with ligher duty ones with the throttle mounting bracket in place.
When the springs were off moving the accelerator pedal just felt like there was too much resistance between the inner and outer cable. I detached the cable from the engine end, tied it to the underside of the bonnet so it was vertical and then dropped 3in1 oil down it drop by drop by drop by drop, wiggling the inner cable occasionally.
This is a long job ( springs and cable, then refitting took about 3 hours ) but the cable is so much smoother now and this job is probably a whole lot easier than fitting a new inner and outer cable.
It's a case of what you get used to but I prefer the lighter pedal feel.
Milky400 said:
With regards to oiling the throttle cable i made a cone out of blue tack stuck it to the end of the cable and filed this with oil and left it as long as it needed to drip done the whole cable.
That's a much better way of lubricating the cable. Wish I had thought of that !
with regards to the oil pressure guage. It is most likely the sender that is situated near to the oil filter.
It could well be the connection as it sits next to oil filter and is exposed to all sort of road crud.
It may well have fallen off the connector.
If you had no pressure there is anothere sender that controls the red LED on the dash. Lights when igition is turned on and if pressure is below 10lbs.
And welcome to the fold, They do become addictive though
Trev
It could well be the connection as it sits next to oil filter and is exposed to all sort of road crud.
It may well have fallen off the connector.
If you had no pressure there is anothere sender that controls the red LED on the dash. Lights when igition is turned on and if pressure is below 10lbs.
And welcome to the fold, They do become addictive though
Trev
Oil pressure was just a wire came off the spade end, nice easy fix
As for the throttle i took it off lube it will engine oil used blue tack cone method ( works well )
Then decided to remove the plenum top and all throttle linkages and springs, rebuilt fully and took one spring off, and the difference is night and day!!
Its made a fantastic car even better and now very easy to live with day to day
As for the knocking noise, i can see the half moon brackets moving on one side, but the bush seems to be fine, ive done the bolts up, and it still seems to be moving, Does the bracket have elongated holes?



As for the throttle i took it off lube it will engine oil used blue tack cone method ( works well )
Then decided to remove the plenum top and all throttle linkages and springs, rebuilt fully and took one spring off, and the difference is night and day!!
Its made a fantastic car even better and now very easy to live with day to day
As for the knocking noise, i can see the half moon brackets moving on one side, but the bush seems to be fine, ive done the bolts up, and it still seems to be moving, Does the bracket have elongated holes?
Alex,
Sounds like you are making good progress.
Re: Springs, I tried mine with a single spring and found, as you have, there is a massive difference.
I figured there was a reason for two springs and felt that if one went ping the other will close off the throttle, which is why I went for the 2x lighter spring option.
The end result is the same and I might be overlly cautious here.
Sounds like you are making good progress.
Re: Springs, I tried mine with a single spring and found, as you have, there is a massive difference.
I figured there was a reason for two springs and felt that if one went ping the other will close off the throttle, which is why I went for the 2x lighter spring option.
The end result is the same and I might be overlly cautious here.
P400PLS said:
You are right.
Just me being cautious then.
I would be equally cautious and go for the "two lighter springs" option. I'm not sure the butterfly return alone would be strong enough to close the throttle against the resistance of the cable. Also the spring would be more likely to go when stretched, i.e. when the throttle is widely open. Being unable to close it instantly could be 'interesting' to say the least!! Just me being cautious then.


nikman said:
P400PLS said:
You are right.
Just me being cautious then.
I would be equally cautious and go for the "two lighter springs" option. I'm not sure the butterfly return alone would be strong enough to close the throttle against the resistance of the cable. Also the spring would be more likely to go when stretched, i.e. when the throttle is widely open. Being unable to close it instantly could be 'interesting' to say the least!! Just me being cautious then.



Quinny said:
For the clonking Diff, try the bolt at the rear.... Quite common for it to work loose
Pretty rare to see a Chim owner getting his hands dirty

Ive done every bolt up at back, there's nothing else :-s
Pretty rare to see a Chim owner getting his hands dirty


Get my hands dirty you kidding me? I spent 8 years working in a body shop
and have a garage full of snap-on tools not been used in 2 years begging me to use them, I cant wait for some thing else to go wrong, which im sure wont be long
Alex
quattrophenia said:
Alexdaredevilz said:
Thanks walt, now i know where to look,
Garfy yup still knocks with roof on
How would you know? Dont tell me you have been out in it with the roof on. That's what you have a boot for, for keeping the roof in.Garfy yup still knocks with roof on
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


