97 Chim what oil
Discussion
Here are my experiences of increasing the viscosity of the oil in my Chimaera.
When I took delivery of my car last year it had just been serviced by a well known Cambridgeshire TVR specialist, the oil was clearly new when the dip stick was inspected.
I was seeing the following pressures.
Idle cold: 30psi
Running Cold: 32psi
Running hot: 30psi
Idle hot: 15psi
After a couple of thousand miles I had a very slight tapping noise when hot, I phoned the TVR specialist to see what oil they used and was told they only use Shell Helix 5/40W fully synthetic
Lets face it the RV8 engine is 1950's design, in my opinion 5/40W is way too thin for this engine.
I changed the oil for Millers CSS 20w50 semi synthetic (this oil is now rated at 20w60), the slight tapping noise completely disappeared and the oil pressures were as follows:
Idle cold: 35psi
Running Cold: 35psi
Running hot: 33psi
Idle hot: 30psi
In summary its my belief that our cars prefer a heavier oil, most of our cars have exceeded 30k miles so moving up a grade is only following the natural engine wear.
Whatever oil you choose make sure it contains zinc which is essential for long tappet a cam life, zinc has been deleted from most modern oils on environmental grounds.
I can highly recommend the Millers CSS 20w60 semi synthetic, I am convinced it provides significant improvements in hot running engine protection over a lighter oil.
It also contains the correct quota of zinc so your cam should last as long as they do in any other engine.
When I took delivery of my car last year it had just been serviced by a well known Cambridgeshire TVR specialist, the oil was clearly new when the dip stick was inspected.
I was seeing the following pressures.
Idle cold: 30psi
Running Cold: 32psi
Running hot: 30psi
Idle hot: 15psi

After a couple of thousand miles I had a very slight tapping noise when hot, I phoned the TVR specialist to see what oil they used and was told they only use Shell Helix 5/40W fully synthetic

Lets face it the RV8 engine is 1950's design, in my opinion 5/40W is way too thin for this engine.
I changed the oil for Millers CSS 20w50 semi synthetic (this oil is now rated at 20w60), the slight tapping noise completely disappeared and the oil pressures were as follows:
Idle cold: 35psi
Running Cold: 35psi
Running hot: 33psi
Idle hot: 30psi

In summary its my belief that our cars prefer a heavier oil, most of our cars have exceeded 30k miles so moving up a grade is only following the natural engine wear.
Whatever oil you choose make sure it contains zinc which is essential for long tappet a cam life, zinc has been deleted from most modern oils on environmental grounds.
I can highly recommend the Millers CSS 20w60 semi synthetic, I am convinced it provides significant improvements in hot running engine protection over a lighter oil.
It also contains the correct quota of zinc so your cam should last as long as they do in any other engine.
Another good choice is the Penrite 15w60 semi synthetic its available from Dingocroft Land Rover at roughly 30% cheaper than the Millers CSS 20w60.
Penrite always add zinc and I have found it gives excellent hot running protection with a slightly faster build up of oil pressure during cold winter start ups.
Penrite 15w60 semi synthetic is now my oil of choice.
Its also well known that the standard TVR oil pressure gauge under-reads.
Str8six told me that when a good quality oil pressure gauge is plumbed directly into the main oil gallery you normally see a true & accurate reading of 10 - 15lbs per sq in above what the TVR gauge is reading.
Whatever you do just make sure the oil is at least 15w50 and that it contains the correct amount of zinc, if you use a thinner oil in my opinion you are risking premature engine wear.
Penrite always add zinc and I have found it gives excellent hot running protection with a slightly faster build up of oil pressure during cold winter start ups.
Penrite 15w60 semi synthetic is now my oil of choice.
Its also well known that the standard TVR oil pressure gauge under-reads.
Str8six told me that when a good quality oil pressure gauge is plumbed directly into the main oil gallery you normally see a true & accurate reading of 10 - 15lbs per sq in above what the TVR gauge is reading.
Whatever you do just make sure the oil is at least 15w50 and that it contains the correct amount of zinc, if you use a thinner oil in my opinion you are risking premature engine wear.
Chimpaholic said:
Here are my experiences of increasing the viscosity of the oil in my Chimaera.
When I took delivery of my car last year it had just been serviced by a well known Cambridgeshire TVR specialist, the oil was clearly new when the dip stick was inspected.
I was seeing the following pressures.
Idle cold: 30psi
Running Cold: 32psi
Running hot: 30psi
Idle hot: 15psi
After a couple of thousand miles I had a very slight tapping noise when hot, I phoned the TVR specialist to see what oil they used and was told they only use Shell Helix 5/40W fully synthetic
Lets face it the RV8 engine is 1950's design, in my opinion 5/40W is way too thin for this engine.
I changed the oil for Millers CSS 20w50 semi synthetic (this oil is now rated at 20w60), the slight tapping noise completely disappeared and the oil pressures were as follows:
Idle cold: 35psi
Running Cold: 35psi
Running hot: 33psi
Idle hot: 30psi
In summary its my belief that our cars prefer a heavier oil, most of our cars have exceeded 30k miles so moving up a grade is only following the natural engine wear.
Whatever oil you choose make sure it contains zinc which is essential for long tappet a cam life, zinc has been deleted from most modern oils on environmental grounds.
I can highly recommend the Millers CSS 20w60 semi synthetic, I am convinced it provides significant improvements in hot running engine protection over a lighter oil.
It also contains the correct quota of zinc so your cam should last as long as they do in any other engine.
+1 this was also a recommendation from SC PowerWhen I took delivery of my car last year it had just been serviced by a well known Cambridgeshire TVR specialist, the oil was clearly new when the dip stick was inspected.
I was seeing the following pressures.
Idle cold: 30psi
Running Cold: 32psi
Running hot: 30psi
Idle hot: 15psi

After a couple of thousand miles I had a very slight tapping noise when hot, I phoned the TVR specialist to see what oil they used and was told they only use Shell Helix 5/40W fully synthetic

Lets face it the RV8 engine is 1950's design, in my opinion 5/40W is way too thin for this engine.
I changed the oil for Millers CSS 20w50 semi synthetic (this oil is now rated at 20w60), the slight tapping noise completely disappeared and the oil pressures were as follows:
Idle cold: 35psi
Running Cold: 35psi
Running hot: 33psi
Idle hot: 30psi

In summary its my belief that our cars prefer a heavier oil, most of our cars have exceeded 30k miles so moving up a grade is only following the natural engine wear.
Whatever oil you choose make sure it contains zinc which is essential for long tappet a cam life, zinc has been deleted from most modern oils on environmental grounds.
I can highly recommend the Millers CSS 20w60 semi synthetic, I am convinced it provides significant improvements in hot running engine protection over a lighter oil.
It also contains the correct quota of zinc so your cam should last as long as they do in any other engine.

just oil changed mine last weekend ,used mobil 15w 50 motorsport formula/genuine lr oil filter ,oil pressure very good when opperating temp reached with 30psi showing on gauge at idle,before change would drop to 15psi(ish),according to service history/bills the previous oil had done a little over 2k,completely agree to changing as often as funds allow with a max of 3k between changes,
(just changed diff oil tonight as well, never a pleasant job but worth it for the knowledge its done)
(just changed diff oil tonight as well, never a pleasant job but worth it for the knowledge its done)

BTW - my pressure gauge packed up a few weeks ago (decided to only read 90+) and the new one reads completely differently from the old one (that I had had for the 6 of of ownership) so everything is relative anyway. Running pressure of around 45ish but tickover pressure shows nearer 20 rather than 10.
jr6yam said:
As always, whatever you use, CHANGE IT EVERY 3000 MILES
I will shortly be buying a Chimaera, with any luck, and have strongly considered doing additional oil changes between services.In the past I have done this (on other cars) without changing the filter, and I have used a Pela oil extractor to suck the oil out via the dipstick tube. This makes the job very, very quick, and there's no need to jack the car up or disturb the sump stud.
Can anyone think of any reason why this wouldn't also work on the TVR V8?
Not sure why there'd be any greater risk of emptying the pump than there is by draining the oil conventionally?
The extractor works by inserting a long flexible tube into the sump via the dipstick tube. It only works by building up a vacuum in the plastic body of the extractor, then you simply wait until you hear a sucking noise (a bit like when you've finished a carton of juice!). It's really quite gentle, so would there really be a risk of emptying the pump?
ETA: Also, I think there's possibly an argument that additional changes are unnecessary if your car is driven frequently. If your car only does, say, 6000 miles a year with long periods of standing then I'd definitely change the oil every 3000 miles. But if you're getting the oil up to temperature by driving every day or so, you're getting rid of the water and acids in the oil and perhaps additional changes aren't necessary.
The extractor works by inserting a long flexible tube into the sump via the dipstick tube. It only works by building up a vacuum in the plastic body of the extractor, then you simply wait until you hear a sucking noise (a bit like when you've finished a carton of juice!). It's really quite gentle, so would there really be a risk of emptying the pump?
ETA: Also, I think there's possibly an argument that additional changes are unnecessary if your car is driven frequently. If your car only does, say, 6000 miles a year with long periods of standing then I'd definitely change the oil every 3000 miles. But if you're getting the oil up to temperature by driving every day or so, you're getting rid of the water and acids in the oil and perhaps additional changes aren't necessary.
Edited by dmjw01 on Thursday 23 September 18:16
Gassing Station | Chimaera | Top of Page | What's New | My Stuff




s , used by TVR because they got it free.I may move to Millers 20w60 symi synthetic in the future.