Radiator leak
Radiator leak
Author
Discussion

madasafrog666

Original Poster:

210 posts

199 months

Sunday 29th August 2010
quotequote all
Hi guys, still new to chim ownership so I thought I would ask the experts on here.
I appear to have a small leak from the bottom passenger side of the radiator.( although it is difficult to see) My question is, is it easy to get the rad out?, it looks a lot more difficult than the MGB I had before. Or would I be better to save time and just take it to the local garage and get them to do it.
Or as the leak is only minor is there somthing I can add to the coolant system like radweld to see if this stops it.??
Also if it is the rad leaking, can they be repaired or do I need a new one?.....cost??

Many thanks Madas....etc

kevin63

4,661 posts

284 months

Sunday 29th August 2010
quotequote all
I would say it is fairly easy to take out, then you can take it to a local rad place and get it sorted. I had mine done for around £150 I think it was and they got it sorted within a couple of days. I got mine done at a place called Auto Rad in Chesterfield, Derbyshire.

Robrine

124 posts

212 months

Sunday 29th August 2010
quotequote all
I've just had mine recored for £170 ish inc VAT. Pretty easy to get out, mines a 94 pre serp, just two nuts to undo, although I did take the fans off first. Theres not much room in there, so it may take a bit of 'wiggling' to get it out. Not a bad job to do at all.smash

cheers

Rob.

madasafrog666

Original Poster:

210 posts

199 months

Sunday 29th August 2010
quotequote all
Thanks guys, I will have a go at it tomorrow. Any idea what a garage would chrage to do the job?


tonys

1,080 posts

254 months

Sunday 29th August 2010
quotequote all
You might find it a lot easier with the bonnet off. Also, a good opportunity to check the hoses and the metal pipe, if it hasn't already been replaced. Stainless replacement pipes are available.

madasafrog666

Original Poster:

210 posts

199 months

Sunday 29th August 2010
quotequote all
Hi, Can you explain what the " metal pipe",?? is there anything on the market like a haynes manual for the TVR.

kevin63

4,661 posts

284 months

Sunday 29th August 2010
quotequote all
You may find some help on here http://www.chimaerapages.com/index.php

spend

12,581 posts

282 months

Sunday 29th August 2010
quotequote all
kevin63 said:
I would say it is fairly easy to take out, then you can take it to a local rad place and get it sorted. I had mine done for around £150 I think it was and they got it sorted within a couple of days. I got mine done at a place called Auto Rad in Chesterfield, Derbyshire.
Went past them the other day and not sure if they are still there BTW... I'll take a closer look next time.

Mark_S_24

405 posts

207 months

Sunday 29th August 2010
quotequote all
madasafrog666 said:
Hi, Can you explain what the " metal pipe",?? is there anything on the market like a haynes manual for the TVR.
http://www.tvrcc-shop.co.uk/acatalog/TVRCC_Catalogue_Road_testsHistoriesCollectors_Guides_34.html

This is as close as you'll get to a Haynes manual, it's refered to on here as "The Bible".

I also have a leak in mine (Again a Pre-Serp) and I was gonna replace the hoses etc too.

http://www.actproducts.co.uk/shop/sc005-tvr-chimaera-preserp-stainless-coolant-pipes-p-341.html

http://www.actproducts.co.uk/shop/hk005a-tvr-chimaera-hose-kit-preserpentine-p-236.html

This is to give an example, there may be other places that are cheaper etc.

Mark

penno

241 posts

261 months

Monday 30th August 2010
quotequote all
Rad it's easy to remove to make it easier remove the air induct hose first. To do this there is bolt passenger side front just up and across from the bonet hinges. undo this the air filter will drop down in the grill/number plate recess undo the clips and pull the hose through the hole by the rad. this give you more space to get it out. undo the top and bottom hose plus the two bolts holding the rad and lift out. It is a bit of a lump so depending on how strong you are it is a good idea to have a helping hand to side it out.

I had mine record for about £100 a yfew years back so its not that bad.


spend

12,581 posts

282 months

Monday 30th August 2010
quotequote all
Tvr made more than one car, and each probably had a design different in one area or another. The induction pipes differ between early & late as does grille access wink

Generally hoses off, fan connectors off, 2 bolts through the bodywork, just lift rad (bottom is secured just with dowels) and flip onto the exhaust y-piece then you can lift out comfortably. No need to remove the bonnet IME.

quattrophenia

1,103 posts

229 months

Monday 30th August 2010
quotequote all
I recently did mine. I took the bonnet off as it made access so much better.
One thing I would say is mark the exact distance between the 2 mounting holes that the rad sits in, on a piece of string and tell the fabricators to weld the new rad to the that exact distance. I didn't do this and when the rad was welded back together it was say 5mm wider than the original and it only just fitted between the engine bay sides and the mounting holes.

madasafrog666

Original Poster:

210 posts

199 months

Tuesday 31st August 2010
quotequote all
Thanks guys for all the comments. I now have a copy of the bible and was reccomended to try a product called Kalimex. www.kalimex.co.uk which fills any leaks in the coolant system. 12 pounds for a small bottle, but money well spent as id did exactly what it said on the tin! within 3 minutes of getting up to temp the leak was sealed, and have done over a hundred miles at the weekend and everything is fine.
A lot cheaper than taking the rad out. Will keep an eye on it over the coming months to see if it remains sealed.smile

Regards Madasafrog

anonymous-user

85 months

Tuesday 31st August 2010
quotequote all
Had mine done about a month ago.

New Aluminium rad, and new hoses cost me just over £1k.

Was apparently a right ar5e to get out (as it has an A/C condensor on it aswell). The bolts had corroded and they had to cut the old fan shrouds out just to remove the old radiator. It was on all counts, a right pig of a job.

I'm glad I didn't try and attempt it myself.