dyno not a good day!!!!
Discussion
wanted to see what my engine was making before puting the supercharger.was expecting at least 190hp to 210hp.than surprise less than 170hp.what can u tell me about the graph????need new cam????anything i should look after????my car has no cat+Y piece+ACT elbow+K&N filter+shorter trumpets mileage is only 44000km always well maintain.well at least by me since 22000km year 2000 model.is this kind of power normal for a 4 litres V8???was expecting at least 50hp per litre.i try to get as close as what TVR quote 240hp before puting anything expensive on it.tks for ur help and advises

Edited by chimaera1855 on Wednesday 1st September 10:22
Edited by chimaera1855 on Wednesday 1st September 18:51
Mine made 235bhp flywheel and 195bhp wheels a few weeks which is good 5bhp short of what they said it came out the factory with only breathing mods. it is still running a little rich so with re-map i think we could get more but dont see the point spending £500+ for a mere 15bhp or so.
spend said:
ISTR someone suggested in the past that the Malaysian built cars were reduced compression as a consequence of available fuel quality?
Hi Dave even a full 2 points lower on the compression wouldnt explain such a low bhp surely? Must be cam wear, timing or something more serious IMO
what is the worst case senario????cam,timing not a big deal!wanted to change the cam anyway.what else can it be???my mechanic says that the car feels alright but here they have less than 15 units so i am more interested about what u guys are thinking.167hp for a V8 4 litres????are u kidding me???i ll FEDEX free beer to uk if u help me to get back my hp ahahah
When I bought my car, I did a compression test and was getting low readings (I think they were in the region of 120psi or 140psi).
Turned out the car was fitted with a vernier timing chain, and the vernier had slipped, so the timing was retarded.
Bought a non adjustable timing chain kit so it couldn't happen again, had the engine timed, and redid the compression test. New readings were 200psi. (This was on a 5.0 engine, which are said to be "HC" - still not sure if this means "high compression", or "high lift cam")
May be worth you checking for a similar problem.
Turned out the car was fitted with a vernier timing chain, and the vernier had slipped, so the timing was retarded.
Bought a non adjustable timing chain kit so it couldn't happen again, had the engine timed, and redid the compression test. New readings were 200psi. (This was on a 5.0 engine, which are said to be "HC" - still not sure if this means "high compression", or "high lift cam")
May be worth you checking for a similar problem.
dbv8 said:
spend said:
ISTR someone suggested in the past that the Malaysian built cars were reduced compression as a consequence of available fuel quality?
Hi Dave even a full 2 points lower on the compression wouldnt explain such a low bhp surely? Must be cam wear, timing or something more serious IMO
At least with the 500 packages you can be reasonably certain of the tuning that comes with the engine, the 4.0's and 4.6's always seem to be a bit of a can of worms when it comes to knowing exactly what is in inside them (originally or serviced/repaired with poorer spec..)
There are even well known 500's that have been downgraded as part of 'upgrade' packages so it's not always so clear cut.
wow u are starting t scare me a bit here.i already told u that it was pretty hard to pass 200km/h could this explain that????i really dont think TVR will sell lowgrade engine to oversea market.not a good way to sell oversea/mhmh hopefully tomorrow will have some answers.keep it coming guys.need as much infos as i can.how come no others TVRs from malaysia here????
Teetertank said:
When I bought my car, I did a compression test and was getting low readings (I think they were in the region of 120psi or 140psi).
Turned out the car was fitted with a vernier timing chain, and the vernier had slipped, so the timing was retarded.
Bought a non adjustable timing chain kit so it couldn't happen again, had the engine timed, and redid the compression test. New readings were 200psi. (This was on a 5.0 engine, which are said to be "HC" - still not sure if this means "high compression", or "high lift cam")
May be worth you checking for a similar problem.
Thats very interesting Teetertank, I wonder if I have the same issues.Turned out the car was fitted with a vernier timing chain, and the vernier had slipped, so the timing was retarded.
Bought a non adjustable timing chain kit so it couldn't happen again, had the engine timed, and redid the compression test. New readings were 200psi. (This was on a 5.0 engine, which are said to be "HC" - still not sure if this means "high compression", or "high lift cam")
May be worth you checking for a similar problem.
My 4.0HC has a vernier timing chain and its well down on power.
I am seeing 188bhp which is not as bad as chimaera1855, but its still telling me something is very wrong.
For me its about going back to first principles:
1) Induction & exhaust restriction
2) Ignition timing
3) Compression test dry then wet (outright & bleed down all cylinders)
4) Injector condition
5) Cam lift at rockers
6) Cam timing
Then its a case of using the results from all the above checks to build up a picture of what's at fault.
As my car runs very smoothly and the AFR was nicely controlled by the Tornado chip at 12.5:1 throughout the rev range my bet is the problem is not related to fuelling.
However if nothing obvious jumps out from my list of tests I guess I need the services of a decent engine tuning centre that understands Lucas 14CUX system & has the kit to test it.
If I have missed something here do let me know.
[quote=Chimpaholic
1) Induction & exhaust restriction
2) Ignition timing
3) Compression test dry then wet (outright & bleed down all cylinders)
4) Injector condition
5) Cam lift at rockers
6) Cam timing
[/quote]
That list sounds reasonable.
I assume you've checked the vacuum advance is working properly?
You should be able to check ignition timing with a timing light.
It's nice to do a compression test for piece of mind that you know you have a relatively healthy, mechanically sound engine.
If it's fuelling ok, then expect injectors to be fine.
Cam lift and timing should be possible with a DTI and just rocker removal (although I think you may have already done this). But checking the cam timing means you need to know the angles, which means you need to know exactly which cam you have, and have the data available. If you have the data available, you should be able to do this without taking the front of the engine off.
1) Induction & exhaust restriction
2) Ignition timing
3) Compression test dry then wet (outright & bleed down all cylinders)
4) Injector condition
5) Cam lift at rockers
6) Cam timing
[/quote]
That list sounds reasonable.
I assume you've checked the vacuum advance is working properly?
You should be able to check ignition timing with a timing light.
It's nice to do a compression test for piece of mind that you know you have a relatively healthy, mechanically sound engine.
If it's fuelling ok, then expect injectors to be fine.
Cam lift and timing should be possible with a DTI and just rocker removal (although I think you may have already done this). But checking the cam timing means you need to know the angles, which means you need to know exactly which cam you have, and have the data available. If you have the data available, you should be able to do this without taking the front of the engine off.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff






