Tyre size on estorils
Discussion
Hi All
I've got the estoril wheels on my non-PAS, 93, 4.0 Chim. They came with the car. Currently the fronts are 225/50/15, the same as the later 5.0 PAS versions.
My question is can the original tyre size 205/60/15 fit on the estorils? My thinking is three fold.
1) The speedo wildly over reads with the current tyre, fitting the original size will rectify this
2) Reduce the stress on the steering components
3) The current tyres slightly foul the arches when on full lock in reverse
Ideally I'd like to keep the estorils, so if I can even get closer to the original it would help.
Thanks
I've got the estoril wheels on my non-PAS, 93, 4.0 Chim. They came with the car. Currently the fronts are 225/50/15, the same as the later 5.0 PAS versions.
My question is can the original tyre size 205/60/15 fit on the estorils? My thinking is three fold.
1) The speedo wildly over reads with the current tyre, fitting the original size will rectify this
2) Reduce the stress on the steering components
3) The current tyres slightly foul the arches when on full lock in reverse
Ideally I'd like to keep the estorils, so if I can even get closer to the original it would help.
Thanks
1. The new tyres would have a greater circumference, so the wheels will rotate slightly slower but the speedo pickup is off the back axle, so replacing the fronts would make no difference.
2. Even though the difference in tread width is ~ 20% it won't 'stress' the steering components.
3. The tyres you want to replace with are 20mm narrower, so they should bring the tyre 10mm further from the bodywork at full lock. That ought to stop the fouling.
2. Even though the difference in tread width is ~ 20% it won't 'stress' the steering components.
3. The tyres you want to replace with are 20mm narrower, so they should bring the tyre 10mm further from the bodywork at full lock. That ought to stop the fouling.
Cider Andy said:
1. The new tyres would have a greater circumference, so the wheels will rotate slightly slower but the speedo pickup is off the back axle, so replacing the fronts would make no difference.
2. Even though the difference in tread width is ~ 20% it won't 'stress' the steering components.
3. The tyres you want to replace with are 20mm narrower, so they should bring the tyre 10mm further from the bodywork at full lock. That ought to stop the fouling.
Thanks for the response. The 'bible' is a bit confusing (probably just me):2. Even though the difference in tread width is ~ 20% it won't 'stress' the steering components.
3. The tyres you want to replace with are 20mm narrower, so they should bring the tyre 10mm further from the bodywork at full lock. That ought to stop the fouling.
'Front tyres must be checked at the limits of the steering and the speedometer may require re calibrating to compensate for the different circumference.'
Might have to look at the back set too now.

MisterT said:
finestjammy said:
My question is can the original tyre size 205/60/15 fit on the estorils? My thinking is three fold.
Isnt the original (non PAS) front tyre size 205/55 x 15? and not 60.MisterT said:
The Chimaera sizes must have been different from the Griff then?
When I first got my '94 Griff it still had the original factory fitted tyres which were 205/55x15. Or is it the case that TVR fitted whatever they could get at the time to get the car out to customer!?
Correct. Griffs were never fitted with 60 profile.When I first got my '94 Griff it still had the original factory fitted tyres which were 205/55x15. Or is it the case that TVR fitted whatever they could get at the time to get the car out to customer!?
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


