Pops and bangs from Chim?
Discussion
How comes mine never seems to pop? Every now and again on the overrun I get a very muted burble-type noise. Never had a full on 'pop' though.
Is there a trick you have to do to get the pops happening? i.e. keep the engine speed up for a few minutes to get the exhaust really hot? Or rev-match the down shift or something?
Only had the Chim500 for a few months so go easy on me!
Is there a trick you have to do to get the pops happening? i.e. keep the engine speed up for a few minutes to get the exhaust really hot? Or rev-match the down shift or something?
Only had the Chim500 for a few months so go easy on me!

My 450 never did it before the exhaust was sleeved. But now I have a gatling gun in the pipes 
2nd or 3rd gear ~4k revs (but will work down to 3k) come off the throttle completely then just gently touch the throttle and hold it - basically feathering it to let a little bit of air and fuel through. This feathering makes mine pop and bang, but you do need hot manifolds IIRC the bang is the unburned fuel igniting inside the exhaust manifolds. After ~2 miles I find they are hot enough to get some good bangs but after a proper hoon they get really loud, more like cracks than bangs.
Luvverley

2nd or 3rd gear ~4k revs (but will work down to 3k) come off the throttle completely then just gently touch the throttle and hold it - basically feathering it to let a little bit of air and fuel through. This feathering makes mine pop and bang, but you do need hot manifolds IIRC the bang is the unburned fuel igniting inside the exhaust manifolds. After ~2 miles I find they are hot enough to get some good bangs but after a proper hoon they get really loud, more like cracks than bangs.
Luvverley

Edited by bigdods on Saturday 11th September 00:14
bigdods said:
2nd or 3rd gear ~4k revs (but will work down to 3k) come off the throttle completely then just gently touch the throttle and hold it - basically feathering it to let a little bit of air and fuel through.
Ahhh, never tried that before! I'll give it a go. 



So this is the trick! (Right Quinny?
)Edited by FreeLitres on Saturday 11th September 07:40
I have a pre cat with standard exhaust but it doesnt pop n bang as loud as id like.
On over run it does burble and pop but it is very muted. I have tried feathering the throttle but makes no difference. With the standard exhaust i think the pops n bangs are still there just that they are absorbed more by the silencer. I think the only way to get them nice and loud is to have the silencer sleeved.
On over run it does burble and pop but it is very muted. I have tried feathering the throttle but makes no difference. With the standard exhaust i think the pops n bangs are still there just that they are absorbed more by the silencer. I think the only way to get them nice and loud is to have the silencer sleeved.Quinny said:
But, by just feathering the gas on the over run, I can "induce" bigger bangs...
So yes the trick is to just allow a little bit of fuel and air in..... Try it and see what happens
So yes the trick is to just allow a little bit of fuel and air in..... Try it and see what happens

feathering the throttle does indeed work even with a standard exhaust with cats and pre cats in (it is very muted tho). I now have an ACT Cherry Bomb back box and I get the same pops and bangs but a little louder than before (all cats still in). Also you can hear them much clearer with the roof off and the back roof section folded down.... of course being a Chim that may be an issue 
Have a quick look through this thread as well.
http://www.pistonheads.com/gassing/topic.asp?h=0&a...
If you want a technical fix, you need to wind the throttle pot voltage up beyond the point the ECU cuts the fuel when the throttle is closed. The best way to do this is to elongate the throttle pot mounting holes to give some more adjustment, and then get someone to hold the throttle wide open and measure the voltage across the red and green wire on the pot. You then need to rotate the pot to maximise this voltage which is likely to be between 4.8 and 5 volts, so its higher than the normally required 4.6 volts. If you are lucky this will lift the throttle shut voltage above the fuel cut off point so the injectors are still firing allowing some unburnt fuel into a hot exhaust, but it if you are already at peak voltage before you elongate the holes you it wont make any difference,( due the the physical swing of the pot and the degrees the butterfly opens.)
Strange how two supposedly similar models get different sounds.
I have fully sleeved exhausts and pre cats removed. Pops and bangs on demand, even on 'upshifts' sometimes and in any gear.
It always gave plenty on over run even before the precats were removed.
Perhaps it's the engines way of saying thankyou for being surrounded by the better looking body
I have fully sleeved exhausts and pre cats removed. Pops and bangs on demand, even on 'upshifts' sometimes and in any gear.
It always gave plenty on over run even before the precats were removed.
Perhaps it's the engines way of saying thankyou for being surrounded by the better looking body

Mine pops and bangs without any provoking, you can get a nice couple pops between up shifts, on the odd occasions you can even get a Cerbera style 'explosion' 
Pre-cats have been removed, but main cat is still present, my exhaust is a bit of a special though featuring Cherry bombs
I'm hoping to get flames once the main cat is removed
.

Pre-cats have been removed, but main cat is still present, my exhaust is a bit of a special though featuring Cherry bombs

I'm hoping to get flames once the main cat is removed
.Gassing Station | Chimaera | Top of Page | What's New | My Stuff





The Griff section must be quiet tonight...