Where do you run yours?
Where do you run yours?
Author
Discussion

Teetertank

Original Poster:

358 posts

218 months

Friday 17th September 2010
quotequote all
Trying to see where to run the extra cables needed to install a Megasquirt - but can't see an obvious place to get the cables through from the engine bay to battery/ECU location.

Any ideas?

hiltonig

3,153 posts

239 months

Friday 17th September 2010
quotequote all
There is only one hole, same one as all other ecu cables

Meatball

1,638 posts

241 months

Friday 17th September 2010
quotequote all
Im running mine up the back of the fuse box and through the ring piece to the left of the wiper motor

Pupp

13,043 posts

303 months

Friday 17th September 2010
quotequote all
Lambda controller in n/s wing void with wiring above wheelarch to cabin works well

Teetertank

Original Poster:

358 posts

218 months

Saturday 18th September 2010
quotequote all
Meatball said:
Im running mine up the back of the fuse box and through the ring piece to the left of the wiper motor
Heard that mentioned before and looked for it, but never saw a way through near the wiper motor. Do you know if exists on all models?


Teetertank

Original Poster:

358 posts

218 months

Saturday 18th September 2010
quotequote all
Pupp said:
Lambda controller in n/s wing void with wiring above wheelarch to cabin works well

Had a look for this one in the past too when trying to run new cables to the lights. Wasn't able to poke something through. Remember it being close but never managed it - can't remember exactly what it was that prevented it.

Any tips, can can it be done through the access hatch in the wheel arch, ie. without removing the headlights?

Pupp

13,043 posts

303 months

Saturday 18th September 2010
quotequote all
Teetertank said:
Pupp said:
Lambda controller in n/s wing void with wiring above wheelarch to cabin works well

Had a look for this one in the past too when trying to run new cables to the lights. Wasn't able to poke something through. Remember it being close but never managed it - can't remember exactly what it was that prevented it.

Any tips, can can it be done through the access hatch in the wheel arch, ie. without removing the headlights?
That's exactly how I did it... a set of small threading rods from Maplins (like mini drain rods) poked through from inside the cabin, top left above the footwell/below the windscreen corner (there will be a foam 'plug' that will need to be pulled out), runs full length to behind the headlights. I 'glued' the controller to the imnner surface next to the hatch with black polyeurethene (sikaflex) type stuff and the lead to the sensor (in Y piece) enters engine bay above air hose (made small grommetted hole by simply filing upwards after removing air hose (looks like an exagerated keyhole) so the sensor lead piggy-backs above the air hose (no need to disturb plugs etc as it all goes through the large air hose aperture)

kenny.R400

1,212 posts

271 months

Saturday 18th September 2010
quotequote all
Meatball said:
and through the ring piece
And I will not lower myself to be the first by commenting on this, it's Childishsmile

Fnarr,Fnarrgetmecoat

Pink_Floyd

900 posts

252 months

Monday 20th September 2010
quotequote all
Pupp said:
the lead to the sensor (in Y piece) enters engine bay above air hose (made small grommetted hole by simply filing upwards after removing air hose (looks like an exagerated keyhole) so the sensor lead piggy-backs above the air hose (no need to disturb plugs etc as it all goes through the large air hose aperture)
Got a picture of this ?

drew.h

526 posts

220 months

Monday 20th September 2010
quotequote all
I'm going to be fitting one soon. What extra wires are needed? I thought the only thing different was a temperature sensor rather than the MAF, which I was planning on using the MAF wire for.

I was hoping just to make an adapter cable from the existing connector to the Mega squirt. Have I got it all wrong?

Teetertank

Original Poster:

358 posts

218 months

Monday 20th September 2010
quotequote all
drew.h said:
I'm going to be fitting one soon. What extra wires are needed? I thought the only thing different was a temperature sensor rather than the MAF, which I was planning on using the MAF wire for.

I was hoping just to make an adapter cable from the existing connector to the Mega squirt. Have I got it all wrong?
You are thinking along the right lines. I too am making up an adaptor cable to interface the Megasquirt to the TVR ECU.

But you will need the following extra cables:

1. VR sensor input (I'm using Ford EDIS, which means you need a PIP & SAW signal)This is a 2-core screened cable.

2. Vacuum hose think it's 3 or 4mm internal

3. Ground cables - to be run separately if you want to be safe about your earthing. Large gauge recommended for those.

4. Ignition cables if you are driving coil packs directly.


The majority of wires in the existing loom can be reused, as you are hoping.

Pupp

13,043 posts

303 months

Monday 20th September 2010
quotequote all
Teetertank said:
But you will need the following extra cables:

1. VR sensor input (I'm using Ford EDIS, which means you need a PIP & SAW signal)This is a 2-core screened cable.

2. Vacuum hose think it's 3 or 4mm internal

3. Ground cables - to be run separately if you want to be safe about your earthing. Large gauge recommended for those.

4. Ignition cables if you are driving coil packs directly.


The majority of wires in the existing loom can be reused, as you are hoping.
While you can re-use the existing engine loom if you really want to, why would you really want to given that it contains about a sackload of 'extra' cabling and connectors that is redundant and given that it'll be well oxidised by now. No brainer for a minimalist new loom in my book smile

drew.h

526 posts

220 months

Monday 27th September 2010
quotequote all
I'd like to keep it as standard so I can replace the 14CUX any time I want. I'm only fitting it in the hope it solves the shunting.

Looking into it more, I have a Megasquirt 1 with a v2.2 circuit board, so don't need the VR sensor, but I do need the vacuum hose.

Johno

8,593 posts

313 months

Tuesday 28th September 2010
quotequote all
Inner wing wiring, I use 2 wire coat hangers, bent and wrapped in the middle covered with tape. Create a hook in one end and feed through from the hole by glovebox all the way down to the fron light pod if needed . . . My WB sensor is plumbed in like this with the wiring coming out through a grommet by the air intake pipe as per others.

As for using the existing wiring, I wouldn't. I could wait to get rid of that god awful bag of bits, unnecessary wiring and reduce the wieght, increase it's durability and improve the overall tidyness of the engine bay. . .

I appreciate people wanting to keeop things standard, but standard can be improved without making it an obvious 'modification', then I'd go for that . .