Lambda probe thread size/bungs needed
Lambda probe thread size/bungs needed
Author
Discussion

Simon says

Original Poster:

19,466 posts

252 months

Sunday 19th September 2010
quotequote all
Some time back someone on these here forums posted up a link to some allen headed bolts to plug the original/stock manifold Lambda probe holes in both manifolds,would be grateful if that person could do so again thumbup I have 12x1.25mm swimming round my had for some reason confused but then there is a lot of oxygen in there too also rolleyes

Edited by Simon says on Sunday 19th September 10:09

spend

12,581 posts

282 months

Sunday 19th September 2010
quotequote all
Cut them out, there is a massive obtrusion formed by the housing/bung it must be @2.5" deep.

Easiest method is to ream out to size & weld in M18 bungs, then grid back excess from inside IMHO. I think you might be able to this in-situ with the Ypiece removed?

Simon says

Original Poster:

19,466 posts

252 months

Sunday 19th September 2010
quotequote all
Thanks Spend,that's why I wanted the bungs in place but didn't realize the bosses protruded so much frown they can come out then idea I plan on pulling the motor over the autumn anyways for a freshen up so can deal with at the same time thumbup

Edited by Simon says on Sunday 19th September 11:29

spend

12,581 posts

282 months

Sunday 19th September 2010
quotequote all
Simon says said:
..didn't realize the bosses protruded so much..
They are actually rather ugly if you care to look, an attempt to get the sensor tip in the middle of the flow in the large collector I guess?

As usual when you change things you have to review why existing designs were done the way they were and if it's more sensible to change them based upon new parameters... More understanding is gleaned from the decisions to dispense with / alter / modify things than actually repairing or using them IME wink

Pupp

13,044 posts

303 months

Sunday 19th September 2010
quotequote all
In the meantime, m12x 1.25 is the size to bung them. Such is the volume, I can't see the bosses being that harmful unless they give rise to some odd standing wave reflections...

Simon says

Original Poster:

19,466 posts

252 months

Sunday 19th September 2010
quotequote all
Thank you chaps thumbup

Meatball

1,638 posts

241 months

Sunday 19th September 2010
quotequote all
Simon let us know what you do in the end as i need to sort mine out at some point

Simon says

Original Poster:

19,466 posts

252 months

Sunday 19th September 2010
quotequote all
Meatball said:
Simon let us know what you do in the end as i need to sort mine out at some point
OK Ben will do,used the car on Saturday and did some more datalogging got a real nice fuel curve at the moment,with my switchable maps hardwired I can switch between the 2 if I cock things up not needed to yet lol,my Innovate LM2 kit as finely come into its own since the recent firmware update really pleased with it now as it just works,before I was getting freezing,logging failure etc,don't you just love companies releasing hardware unfinished? rolleyes

Edited by Simon says on Sunday 19th September 18:44

Meatball

1,638 posts

241 months

Sunday 19th September 2010
quotequote all
Simon says said:
Meatball said:
Simon let us know what you do in the end as i need to sort mine out at some point
OK Ben will do,used the car on Saturday and did some more datalogging got a real nice fuel curve at the moment,with my switchable maps hardwired I can switch between the 2 if I cock things up not needed to yet lol,my Innovate LM2 kit as finely come into its own since the recent firmware update really pleased with it now as it just works,before I was getting freezing,logging failure etc,don't you just love companies releasing hardware unfinished? rolleyes

Edited by Simon says on Sunday 19th September 18:44
I got mine running today on the P38 coil packs it started on the first turn of the key bounce
I just need a few tweeks and i should be driving

Simon says

Original Poster:

19,466 posts

252 months

Monday 20th September 2010
quotequote all
Meatball said:
Simon says said:
Meatball said:
Simon let us know what you do in the end as i need to sort mine out at some point
OK Ben will do,used the car on Saturday and did some more datalogging got a real nice fuel curve at the moment,with my switchable maps hardwired I can switch between the 2 if I cock things up not needed to yet lol,my Innovate LM2 kit as finely come into its own since the recent firmware update really pleased with it now as it just works,before I was getting freezing,logging failure etc,don't you just love companies releasing hardware unfinished? rolleyes

Edited by Simon says on Sunday 19th September 18:44
I got mine running today on the P38 coil packs it started on the first turn of the key bounce
I just need a few tweeks and i should be driving
Well done Ben,are they like this ? http://cgi.ebay.co.uk/Coil-Pack-Discovery-V8-98-/1... just curious really wink

Edited by Simon says on Monday 20th September 10:09

Meatball

1,638 posts

241 months

Monday 20th September 2010
quotequote all
Simon says said:
Meatball said:
Simon says said:
Meatball said:
Simon let us know what you do in the end as i need to sort mine out at some point
OK Ben will do,used the car on Saturday and did some more datalogging got a real nice fuel curve at the moment,with my switchable maps hardwired I can switch between the 2 if I cock things up not needed to yet lol,my Innovate LM2 kit as finely come into its own since the recent firmware update really pleased with it now as it just works,before I was getting freezing,logging failure etc,don't you just love companies releasing hardware unfinished? rolleyes

Edited by Simon says on Sunday 19th September 18:44
I got mine running today on the P38 coil packs it started on the first turn of the key bounce
I just need a few tweeks and i should be driving
Well done Ben,are they like this ? http://cgi.ebay.co.uk/Coil-Pack-Discovery-V8-98-/1... just curious really wink

Edited by Simon says on Monday 20th September 10:09
No mate ive got the ones that bolt onto the back of the inlet manifold/fuel rail http://cgi.ebay.co.uk/Ignition-Coil-Pack-P38-V8-Ra...
Its a bit of a squeeze with the twin plenum and water pipes - but its made the installation nice and tidy. smile

Meatball

1,638 posts

241 months

Monday 20th September 2010
quotequote all
Simon says said:
Meatball said:
Simon says said:
Meatball said:
Simon let us know what you do in the end as i need to sort mine out at some point
OK Ben will do,used the car on Saturday and did some more datalogging got a real nice fuel curve at the moment,with my switchable maps hardwired I can switch between the 2 if I cock things up not needed to yet lol,my Innovate LM2 kit as finely come into its own since the recent firmware update really pleased with it now as it just works,before I was getting freezing,logging failure etc,don't you just love companies releasing hardware unfinished? rolleyes

Edited by Simon says on Sunday 19th September 18:44
I got mine running today on the P38 coil packs it started on the first turn of the key bounce
I just need a few tweeks and i should be driving
Well done Ben,are they like this ? http://cgi.ebay.co.uk/Coil-Pack-Discovery-V8-98-/1... just curious really wink

Edited by Simon says on Monday 20th September 10:09
No mate ive got the ones that bolt onto the back of the inlet manifold/fuel rail http://cgi.ebay.co.uk/Ignition-Coil-Pack-P38-V8-Ra...
Its a bit of a squeeze with the twin plenum and water pipes - but its made the installation nice and tidy. smile

Meatball

1,638 posts

241 months

Monday 20th September 2010
quotequote all
Simon says said:
Meatball said:
Simon says said:
Meatball said:
Simon says said:
Meatball said:
Simon let us know what you do in the end as i need to sort mine out at some point
OK Ben will do,used the car on Saturday and did some more datalogging got a real nice fuel curve at the moment,with my switchable maps hardwired I can switch between the 2 if I cock things up not needed to yet lol,my Innovate LM2 kit as finely come into its own since the recent firmware update really pleased with it now as it just works,before I was getting freezing,logging failure etc,don't you just love companies releasing hardware unfinished? rolleyes

Edited by Simon says on Sunday 19th September 18:44
I got mine running today on the P38 coil packs it started on the first turn of the key bounce
I just need a few tweeks and i should be driving
Well done Ben,are they like this ? http://cgi.ebay.co.uk/Coil-Pack-Discovery-V8-98-/1... just curious really wink

Edited by Simon says on Monday 20th September 10:09
No mate ive got the ones that bolt onto the back of the inlet manifold/fuel rail http://cgi.ebay.co.uk/Ignition-Coil-Pack-P38-V8-Ra...
Its a bit of a squeeze with the twin plenum and water pipes - but its made the installation nice and tidy. smile
Oh scratchchin I see that type yes I can see that making for a tidy install and no need to make up brackets I presume? thumbup
Yes mate i even used my old dizzy leads paperbag they are a bit long...they will do for now besides they are only 6 months old.

Pupp

13,044 posts

303 months

Monday 20th September 2010
quotequote all
Simon says said:
slightly off topic any of us lot using after-market engine management who's using the purge valve/carbon canister?
Yep, still used here.... just drive the valve off a spare output on certain rpm/load conditions being met (I forget what exactly but can check if anyone cares). Why would you not use on TBs, assuming air box(es) is/are employed?

Simon says

Original Poster:

19,466 posts

252 months

Monday 20th September 2010
quotequote all
I have the output also,i was just curious who does who dont Pupp wink

Pink_Floyd

900 posts

252 months

Monday 20th September 2010
quotequote all
Meatball said:
No mate ive got the ones that bolt onto the back of the inlet manifold/fuel rail http://cgi.ebay.co.uk/Ignition-Coil-Pack-P38-V8-Ra...
Its a bit of a squeeze with the twin plenum and water pipes - but its made the installation nice and tidy. smile
Did you use a plug to connect to the coil packs and if so where did you get it from.

Meatball

1,638 posts

241 months

Tuesday 21st September 2010
quotequote all
Pink_Floyd said:
Meatball said:
No mate ive got the ones that bolt onto the back of the inlet manifold/fuel rail http://cgi.ebay.co.uk/Ignition-Coil-Pack-P38-V8-Ra...
Its a bit of a squeeze with the twin plenum and water pipes - but its made the installation nice and tidy. smile
Did you use a plug to connect to the coil packs and if so where did you get it from.
No mate, i cut the old one off and soldered the wires, i couldnt see the point if the coil pack dies ill need to remove the plenum to get to them anyway.

spend

12,581 posts

282 months

Tuesday 21st September 2010
quotequote all
Why do TB's make any odds at all to whether you keep the charcoal cannister confused

spend

12,581 posts

282 months

Tuesday 21st September 2010
quotequote all
There is vacuum, I have no idea what you are talking about / where you're coming from... Do you think AJP's & speed6's etc. can't have carbon cannisters or something...