Diagnosing drop links
Discussion
Is there any way of diagnosing drop links as the cause of rattling over rough-ish tarmac at the front end? I've had a look on a ramp but with wheels hanging any possible play is taken up...
I'm bearing in mind shocks, ball joints and other possible culprits (radiator being loose, and general body knocking I think has been ruled out on my car) but thought i'd start with drop links. Car has done 43k and is in very good condition underneath and generally.
I'm bearing in mind shocks, ball joints and other possible culprits (radiator being loose, and general body knocking I think has been ruled out on my car) but thought i'd start with drop links. Car has done 43k and is in very good condition underneath and generally.
Just remove them, each one is only fixed by two nuts so they can be off in minutes.
You can't really see how bad they are until they are off the car.
If they are OK (& I bet they wont be) make sure you use new NyLock nuts when you re-fit them.
My drop links looked OK until I removed them.
Have a look at my post here.
http://www.pistonheads.com/gassing/topic.asp?h=0&a...
I can thoroughly recommend the Leven rose jointed drop links if you want to take the opportunity to upgrade.
However if you discover your current drop links are badly worn you will probably see a massive improvement from just fitting new standard parts.
It seems the standard drop links don't have a very long life at all, so I would say they are more of a service schedule consumable part and should be replaced every 30,000 miles or sooner if worn.
Everything on the Chim/Griff suspension & steering wears significantly more rapidly than on your modern Euro box.
Suspension bushes, top joints, bottom joints, track rod ends and those drop links all get a very hard life because of heat and the wide profile tyres fitted.
Most of the components actually come from other cars that were never designed for rapid cornering and 150 mph top speeds.
What people forget is that Ferraris and Lambos eat their suspension components too, its just our cars are often run on a budget.
The average Ferrari owner will accept the cost of a suspension refresh every 30,000 miles where the average TVR owner may not, the point is they are both high performance vehicles that need to be maintained in a different way to your daily hack.
I would also suggest that you make sure all the components I have mentioned are in perfect condition and that you pay for a proper full geometry check/adjust before you splash out on a set of fancy adjustable dampers.
The standard Bilsteins are actually quite good shocks when they are in fine fettle, obviously if they are worn or leaking they need to be rebuilt or changed for something new immediately.
In my experience if all the links, dampers, wishbone bushes and joints are all spot on, the Chim & Griffs will handle very well indeed.
If any of these components are worn or the geometry is out of adjustment our cars can be very unpredictable.
If a number of these components are worn they will all combine forces to try and kill you.
The moral of the story is:
"DON'T SKIMP ON YOUR SUSPENSION"
You can't really see how bad they are until they are off the car.
If they are OK (& I bet they wont be) make sure you use new NyLock nuts when you re-fit them.
My drop links looked OK until I removed them.
Have a look at my post here.
http://www.pistonheads.com/gassing/topic.asp?h=0&a...
I can thoroughly recommend the Leven rose jointed drop links if you want to take the opportunity to upgrade.
However if you discover your current drop links are badly worn you will probably see a massive improvement from just fitting new standard parts.
It seems the standard drop links don't have a very long life at all, so I would say they are more of a service schedule consumable part and should be replaced every 30,000 miles or sooner if worn.
Everything on the Chim/Griff suspension & steering wears significantly more rapidly than on your modern Euro box.
Suspension bushes, top joints, bottom joints, track rod ends and those drop links all get a very hard life because of heat and the wide profile tyres fitted.
Most of the components actually come from other cars that were never designed for rapid cornering and 150 mph top speeds.
What people forget is that Ferraris and Lambos eat their suspension components too, its just our cars are often run on a budget.
The average Ferrari owner will accept the cost of a suspension refresh every 30,000 miles where the average TVR owner may not, the point is they are both high performance vehicles that need to be maintained in a different way to your daily hack.
I would also suggest that you make sure all the components I have mentioned are in perfect condition and that you pay for a proper full geometry check/adjust before you splash out on a set of fancy adjustable dampers.
The standard Bilsteins are actually quite good shocks when they are in fine fettle, obviously if they are worn or leaking they need to be rebuilt or changed for something new immediately.
In my experience if all the links, dampers, wishbone bushes and joints are all spot on, the Chim & Griffs will handle very well indeed.
If any of these components are worn or the geometry is out of adjustment our cars can be very unpredictable.
If a number of these components are worn they will all combine forces to try and kill you.
The moral of the story is:
"DON'T SKIMP ON YOUR SUSPENSION"
For safety's sake... PLEASE DO NOT REMOVE both droplinks and run the car with the ARB attached. The arb can drop down and hit the suspension, jam it or worse dig into the ground. The rear is particularly prone to this because of its position under the car.
All you need to to check the drop links is to remove just one. That way there is no force on the ARB but more importantly the ARB is not left hanging in mid air.
If the knocking goes then it is a time for a ARB refurb. If it is still there, attach the one you took off and undo the other one to do a further check.
One other point is the rear ARB droplink plate often breaks as the top bush tries to twist it so it is worth checking mounts and bushes. While you are at it, measure the diameter of the ARB as you will need this info when getting new ARB bushes. TVR seemed to chop and change depending on the astral alignment which makes it difficult for us suppliers.
I don't know where the 30k mile life comes from... the ones on my Wedge lasted about 6-8 weeks at a time, which is what prompted me to develop my range of droplinks in the first place.
All you need to to check the drop links is to remove just one. That way there is no force on the ARB but more importantly the ARB is not left hanging in mid air.
If the knocking goes then it is a time for a ARB refurb. If it is still there, attach the one you took off and undo the other one to do a further check.
One other point is the rear ARB droplink plate often breaks as the top bush tries to twist it so it is worth checking mounts and bushes. While you are at it, measure the diameter of the ARB as you will need this info when getting new ARB bushes. TVR seemed to chop and change depending on the astral alignment which makes it difficult for us suppliers.
I don't know where the 30k mile life comes from... the ones on my Wedge lasted about 6-8 weeks at a time, which is what prompted me to develop my range of droplinks in the first place.
Edited by shpub on Wednesday 22 September 14:07
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


