exhaust manifolds 4lt chim
exhaust manifolds 4lt chim
Author
Discussion

philburch

Original Poster:

214 posts

200 months

Sunday 26th September 2010
quotequote all
Just trying to change the exhaust manifolds on my 4lt chim 1996 as they are cracked, i have managed to get a pair of another '96. Excuse my ignorance but is the catalyst in the manifolds or the y piece. The manifolds i want to put on seen to have a honeycomb type material inside, the ones i have just taken off havn't got anything inside. If i put these on is it going to affect the performance, or have i got the wrong ones for my car??? Any infomation you can give would be greatly appreciated.

anonymous-user

85 months

Sunday 26th September 2010
quotequote all
I don't know all this answer but some of it.
The manifolds on may car 99, do have cats in them , a honeycombed type set up. Think this is the pre cat. I also think there is some in the y piece also, main cat.

When mine failed I got them welded up and then water tested, they are OK right now, but I have only done about 300 miles since and I do notice when I rev the engine it all looks to move a bit, so I am not sure how long it will last.

neal1980

2,585 posts

270 months

Sunday 26th September 2010
quotequote all
Hi,

There are cats as standard in both of the manifolds (precats) then the big one in the Y Piece.

Sounds like someone has removed the pre-cats already on your old manifolds. Its easy enough to do just bash them out one way or another. If you leave them in it will sound quieter. And probably have a higher under bonnet temperature. Lots of reports of them breaking down as well.

In my opinion get rid of the pre-cats, just like your old ones smile

philburch

Original Poster:

214 posts

200 months

Sunday 26th September 2010
quotequote all
thanks for the replies dont know how you would get them welded because the cracks are on the inside of the four pipes where they go into the main block. i guess one way would be to cut it in half and weld it up from the inside and weld it back together
Any thoughts?????

anonymous-user

85 months

Sunday 26th September 2010
quotequote all
That is exactly what was done. A chap in Sussex did it for me and the work is to a high standard.
PM me if you want the details of where I went and the cost etc.

philburch

Original Poster:

214 posts

200 months

Sunday 26th September 2010
quotequote all
Thank's for the offer,my cousin is atop man with a welder(has his own engineering company)will go and see him tomorrow and see what he think's.As the cat's have been removed i guess that is why it sounds noisy around the engine bay.

SILICONE KID

14,997 posts

262 months

Sunday 26th September 2010
quotequote all
You will find that the four in to one cracks due to worn engine mounts so i would check them..Before you fit those manifolds fill them up with water as mine pcensoredt out


Edited by SILICONE KID on Sunday 26th September 22:25

philburch

Original Poster:

214 posts

200 months

Monday 27th September 2010
quotequote all
I replaced the engine mounts about six weeks ago as they had split,guess they had already cracked the manifold.If anybody is interested i pressure tested my exhaust system by stuffing a tennis ball in each of the exhaust pipes,in one tennis ball i made two holes opposite each other in one i fitted a stainless tyre valve connected it to an air line on alow pressure and found my leeks.Dont know if anybody has tried this before but it worked realy well.

project 112

83 posts

213 months

Sunday 3rd October 2010
quotequote all
just a quick question while on the subject of manifolds, when refitting is it worth using s/s bolts you know the ones, always on ebay at what seem like a reasonable price. the reason i ask is because i seem to remember reading (on this forum i think) that they could have a reaction with the ali block or something to do with not getting the correct torque,am i better keeping to the standard items? thoughts anybody?

Alexdaredevilz

5,697 posts

210 months

Sunday 3rd October 2010
quotequote all
I think there stainless as standard? just throw them under a wire wheel and refit

project 112

83 posts

213 months

Sunday 3rd October 2010
quotequote all
cheers thanks for that