Where's All The Water Coming From?!?!?!
Discussion
My engine has decided to spit out all it's coolant 
It all seems to be coming from the front of the engine, somewhere around the thermostat housing, water pump kind of area, but everything I can see without stripping it all down seems water tight...
Hoses - OK
Thermostat Housing - OK
Water Pump - OK
Wondering if it could be the valley gasket...or something a whole lot more sinister
Engine still runs fine - I noticed the temperature rising towards 90 whilst driving along yesterday and stopped before it got hot...
No milkyness in the oil...
Time to roll up my sleeves and get stripping...ooooeeerrr...
Any thoughts or previous similar experiences greatfully received
Giles
PS. Many thanks to the Griff couple who stopped to offer help (but didn't seem too keen on doing a straight swap, even though the lady quite fancied the power steering on my car versus hers) and also the ex-Tuscan owner who offer to take me to the pub and commiserate until the AA arrived! You don't get that kind of offer from drivers of regular cars!!!

It all seems to be coming from the front of the engine, somewhere around the thermostat housing, water pump kind of area, but everything I can see without stripping it all down seems water tight...
Hoses - OK
Thermostat Housing - OK
Water Pump - OK
Wondering if it could be the valley gasket...or something a whole lot more sinister

Engine still runs fine - I noticed the temperature rising towards 90 whilst driving along yesterday and stopped before it got hot...
No milkyness in the oil...
Time to roll up my sleeves and get stripping...ooooeeerrr...
Any thoughts or previous similar experiences greatfully received

Giles
PS. Many thanks to the Griff couple who stopped to offer help (but didn't seem too keen on doing a straight swap, even though the lady quite fancied the power steering on my car versus hers) and also the ex-Tuscan owner who offer to take me to the pub and commiserate until the AA arrived! You don't get that kind of offer from drivers of regular cars!!!
Have just checked the swirl pot - all OK and intact - but thanks for the suggestion.
Seems to be a fair bit of water lying around the base of the distributor and on the water pump and lower down around the oil filter too.
I'll have to top it all up and run it to see if that gives anything away...
Giles
Seems to be a fair bit of water lying around the base of the distributor and on the water pump and lower down around the oil filter too.
I'll have to top it all up and run it to see if that gives anything away...
Giles
Dry everything off, clean with degreaser and such and allow to dry. Put kitchen roll in various places and then start engine. Run until warm through and then, after switching engine off, check kitchen roll for dampness.
If all dry then run through procedure again until your get a damp spot.
This will generally only highlight the area but then you can try it again around where it came last time.
The thermostat housing and pump is the favourite. The gasket can go. Pinholes in pipes or a poor joint.
The water pump bearing can start to go and there can be no discernable movement yet it can still leak.
If it's the valley gasket, could you let me know?
Derek
If all dry then run through procedure again until your get a damp spot.
This will generally only highlight the area but then you can try it again around where it came last time.
The thermostat housing and pump is the favourite. The gasket can go. Pinholes in pipes or a poor joint.
The water pump bearing can start to go and there can be no discernable movement yet it can still leak.
If it's the valley gasket, could you let me know?
Derek
Edited by Derek Smith on Friday 1st October 16:52
Are you sure it's not a microscopic hole in the Rad?, I spent ages trying to find where my Chimaera was leaking from, eventually traced it to a pin hole in the rad which was spraying quite a distance in the engine bay when hot and under pressure. This also lets air into the system and plays havoc. Can you hear bubbling when inside the car? this usually indicates air being let into the system. Once the rad was replaced on mine it was completely cured. Good luck.
Clippy said:
The rad was re-cored last year and everything in front of the crank pulley looks dry, but it's still a possibility - I'll keep an eye on it when I fire her up tomorrow for my hot anti-freeze shower!!
Giles
Just out of interest if it is a serp engine it could be the front cover gasket, have a close look at the passenger side top of the front cover.Giles
OK - filled up the swirl pot last night and bled the radiator...
...and there's a slow but steady drip drip hitting the crosmember just in front of the oil filter.
Didn't get a chance to start it up, which I will now do on the ramps so I can see where the leak's coming from, but it now appears to be lower down than the valley gasket, so first port of call is the water pump...
More news as we have it...
Giles
...and there's a slow but steady drip drip hitting the crosmember just in front of the oil filter.
Didn't get a chance to start it up, which I will now do on the ramps so I can see where the leak's coming from, but it now appears to be lower down than the valley gasket, so first port of call is the water pump...
More news as we have it...
Giles
Breakthrough of sorts...
The water's coming from the front cover.
On the top left corner (as you look at the front of the car) behind/below the alternator there's water seeping out when I squeeze the top hose.
There's a lug at that point that looks like it has a stud in it - and I'm guessing that the stud should be a bolt and that the head of the bolt has gone AWOL.
Time to dig out my copy of the Bible and pray...errr, no...work out what should be in that corner of the cover...
...again any clues from those of you who know would be gratefully received!
Giles
The water's coming from the front cover.
On the top left corner (as you look at the front of the car) behind/below the alternator there's water seeping out when I squeeze the top hose.
There's a lug at that point that looks like it has a stud in it - and I'm guessing that the stud should be a bolt and that the head of the bolt has gone AWOL.
Time to dig out my copy of the Bible and pray...errr, no...work out what should be in that corner of the cover...
...again any clues from those of you who know would be gratefully received!
Giles
Water is definately coming from the top left corner (looking from the front of the car) of the timing cover, where I believe the waterway feeding the water pump comes through from the block.
I've checked the accessable timing cover bolts and one was loose (1 and a half turns loose) but the join is still weeping even with that tightened up, so I think it's a timing cover off and re-seal job.
Has anyone done this? How hard is this likely to be? Has Quinny done a video for this?!?!?
I can see the sump needs to come off to free up the bottom edge of the cover, the crank pulley and probably the front of engine ancillaries such as alternator to create a bit of elbow room.
Are there any tricks to doing this or is it just a steady slog of stripping down, removing the timing cover and replacing the gasket/re-sealing?
I already had the lovely jobs of manifold gaskets and diff bushes lined up for this winter, but now seem to have something slightly larger and more daunting to tackle too?!
Heeeellllpppppp!!!!!!
Giles
I've checked the accessable timing cover bolts and one was loose (1 and a half turns loose) but the join is still weeping even with that tightened up, so I think it's a timing cover off and re-seal job.
Has anyone done this? How hard is this likely to be? Has Quinny done a video for this?!?!?
I can see the sump needs to come off to free up the bottom edge of the cover, the crank pulley and probably the front of engine ancillaries such as alternator to create a bit of elbow room.
Are there any tricks to doing this or is it just a steady slog of stripping down, removing the timing cover and replacing the gasket/re-sealing?
I already had the lovely jobs of manifold gaskets and diff bushes lined up for this winter, but now seem to have something slightly larger and more daunting to tackle too?!
Heeeellllpppppp!!!!!!
Giles
OTOMH...
Drain the coolant, remove the front sump bolts (into the bottom of the timing cover) & loosen the sump bolts behind at the front of the block, remove ancils (I'd take the water pump off personally & renew that gasket as well). Car in gear and long bar on the front pulley bolt (I'd take the Y-piece off so that you have better access BTW), remove pulley assembly, then hoses from water pump, dizzy out (mark it carefully in position and then angle it comes out at - but if you move cam the marks are waste of time
) and just work round all the bolts (some have a stud near the water pump) then carefully prise off the cover.
Clean everything anally for reassembly, I like a little smear of vaseline on gaskets so that they locate, as well as grease on the dowels, and a thin layer of sealant on the long bolts where water may sit.
Serp water pumps aren't expensive, and any signs of water round the drain hole or generally cackiness consider replacing it now as its a 'free' change IYSWIM.
You may want to change the oil if you didn't get the coolant fully drained and lose some into the sump.
It's all fairly straightforward, don't get fazed by the number of things you have to remove, it's always better to take off more for access so you can see what you are doing if you aren't familiar with layout. It is possible to do it through a keyhole, but lack of visibility and extra dexterity required is only for the more experienced IMHO.
Drain the coolant, remove the front sump bolts (into the bottom of the timing cover) & loosen the sump bolts behind at the front of the block, remove ancils (I'd take the water pump off personally & renew that gasket as well). Car in gear and long bar on the front pulley bolt (I'd take the Y-piece off so that you have better access BTW), remove pulley assembly, then hoses from water pump, dizzy out (mark it carefully in position and then angle it comes out at - but if you move cam the marks are waste of time
) and just work round all the bolts (some have a stud near the water pump) then carefully prise off the cover.Clean everything anally for reassembly, I like a little smear of vaseline on gaskets so that they locate, as well as grease on the dowels, and a thin layer of sealant on the long bolts where water may sit.
Serp water pumps aren't expensive, and any signs of water round the drain hole or generally cackiness consider replacing it now as its a 'free' change IYSWIM.
You may want to change the oil if you didn't get the coolant fully drained and lose some into the sump.
It's all fairly straightforward, don't get fazed by the number of things you have to remove, it's always better to take off more for access so you can see what you are doing if you aren't familiar with layout. It is possible to do it through a keyhole, but lack of visibility and extra dexterity required is only for the more experienced IMHO.
Cheers Spend - that all sounds logical... 
...and while I've got the Y-piece out I might as well have the manifolds off to and do the gaskets (and maybe the pre-cats if I'm really going to town!).
Sounds like the most logcal place to start might be bonnet off too for access...
I'm glad this didn't happen in April before the summer arrived!!!
See you all in about 5 months...
Giles

...and while I've got the Y-piece out I might as well have the manifolds off to and do the gaskets (and maybe the pre-cats if I'm really going to town!).
Sounds like the most logcal place to start might be bonnet off too for access...
I'm glad this didn't happen in April before the summer arrived!!!
See you all in about 5 months...

Giles
Clippy said:
Water is definately coming from the top left corner (looking from the front of the car) of the timing cover, where I believe the waterway feeding the water pump comes through from the block.
I've checked the accessable timing cover bolts and one was loose (1 and a half turns loose) but the join is still weeping even with that tightened up, so I think it's a timing cover off and re-seal job.
Has anyone done this? How hard is this likely to be? Has Quinny done a video for this?!?!?
I can see the sump needs to come off to free up the bottom edge of the cover, the crank pulley and probably the front of engine ancillaries such as alternator to create a bit of elbow room.
Are there any tricks to doing this or is it just a steady slog of stripping down, removing the timing cover and replacing the gasket/re-sealing?
I already had the lovely jobs of manifold gaskets and diff bushes lined up for this winter, but now seem to have something slightly larger and more daunting to tackle too?!
Heeeellllpppppp!!!!!!
Giles
Sorry i meant to say left, i said right hand side in my earlier post, a few of the serpentine engines came out with the earlier pre serp gasket, although it seals when new it is only sealing on about 1mm of gasket you will see when you get it off but it is on the very corner near the front cover dowel, fairly easy to do.I've checked the accessable timing cover bolts and one was loose (1 and a half turns loose) but the join is still weeping even with that tightened up, so I think it's a timing cover off and re-seal job.
Has anyone done this? How hard is this likely to be? Has Quinny done a video for this?!?!?
I can see the sump needs to come off to free up the bottom edge of the cover, the crank pulley and probably the front of engine ancillaries such as alternator to create a bit of elbow room.
Are there any tricks to doing this or is it just a steady slog of stripping down, removing the timing cover and replacing the gasket/re-sealing?
I already had the lovely jobs of manifold gaskets and diff bushes lined up for this winter, but now seem to have something slightly larger and more daunting to tackle too?!
Heeeellllpppppp!!!!!!
Giles
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


