Guys,Diff removal.
Discussion
Quinny made a Youtube video think this is it cant check as my connection at work is slow.
http://www.youtube.com/user/big500#p/u/34/IQkz-s0k...
http://www.youtube.com/user/big500#p/u/34/IQkz-s0k...
Edited by scotty_d on Saturday 2nd October 15:25
Undo diff. Hold diff, tilt 90 degrees and drop out of the chassis. Not too bad as gravity helps. Real swine putting it back though as gravity doesn't help as it tries to stop the diff from going up.
Moral is do not underestimate its weight - it is very heavy indeed! Makes the gearbox feel like a featherweight.
Moral is do not underestimate its weight - it is very heavy indeed! Makes the gearbox feel like a featherweight.
haircutmike said:
Can't wait.
Rear diff mount looks like apita.
Think I'll remove the fuel tank again for access.
Can I leave the prop in place to save g/box oil draining, (recently renewed!)?
Measure the outer diameter of the prop end that goes in the gearbox and make yourself a temp plug [back to your blue peter days.] No seriously this works, i used a plastic cap off an aerosol which was slightly small in dia, plenty of tape later its the correct dia. Pull the prop from the gearbox insert your makeshift plug, jobs a good un. A bit more tape to hold it in situ incase you accidentally knock it, also helps. Your aiming to get the dia correct so it will seal itself against the rear oil seal in the gearbox.Rear diff mount looks like apita.
Think I'll remove the fuel tank again for access.
Can I leave the prop in place to save g/box oil draining, (recently renewed!)?
TJC46 said:
haircutmike said:
Can't wait.
Rear diff mount looks like apita.
Think I'll remove the fuel tank again for access.
Can I leave the prop in place to save g/box oil draining, (recently renewed!)?
Measure the outer diameter of the prop end that goes in the gearbox and make yourself a temp plug [back to your blue peter days.] No seriously this works, i used a plastic cap off an aerosol which was slightly small in dia, plenty of tape later its the correct dia. Pull the prop from the gearbox insert your makeshift plug, jobs a good un. A bit more tape to hold it in situ incase you accidentally knock it, also helps. Your aiming to get the dia correct so it will seal itself against the rear oil seal in the gearbox.Rear diff mount looks like apita.
Think I'll remove the fuel tank again for access.
Can I leave the prop in place to save g/box oil draining, (recently renewed!)?

haircutmike said:
TJC46 said:
haircutmike said:
Can't wait.
Rear diff mount looks like apita.
Think I'll remove the fuel tank again for access.
Can I leave the prop in place to save g/box oil draining, (recently renewed!)?
Measure the outer diameter of the prop end that goes in the gearbox and make yourself a temp plug [back to your blue peter days.] No seriously this works, i used a plastic cap off an aerosol which was slightly small in dia, plenty of tape later its the correct dia. Pull the prop from the gearbox insert your makeshift plug, jobs a good un. A bit more tape to hold it in situ incase you accidentally knock it, also helps. Your aiming to get the dia correct so it will seal itself against the rear oil seal in the gearbox.Rear diff mount looks like apita.
Think I'll remove the fuel tank again for access.
Can I leave the prop in place to save g/box oil draining, (recently renewed!)?

R
roysum said:
haircutmike said:
TJC46 said:
haircutmike said:
Can't wait.
Rear diff mount looks like apita.
Think I'll remove the fuel tank again for access.
Can I leave the prop in place to save g/box oil draining, (recently renewed!)?
Measure the outer diameter of the prop end that goes in the gearbox and make yourself a temp plug [back to your blue peter days.] No seriously this works, i used a plastic cap off an aerosol which was slightly small in dia, plenty of tape later its the correct dia. Pull the prop from the gearbox insert your makeshift plug, jobs a good un. A bit more tape to hold it in situ incase you accidentally knock it, also helps. Your aiming to get the dia correct so it will seal itself against the rear oil seal in the gearbox.Rear diff mount looks like apita.
Think I'll remove the fuel tank again for access.
Can I leave the prop in place to save g/box oil draining, (recently renewed!)?

R
Plenty of diffs have to be shoved quite a long way forward to get out, due to the various rear covers (particularly GKNs). Prop shaft can certainly prevent some diffs coming out, but also pushing forward so that the fore chassis xmember takes some of the weight whilst you twist the diff 90degs and then lower the rear is my preferred routine.
The rear mount (bush) can be undone easily enough through the wheel arches just using rather a lot of extension bars and a suitable spanner 'jamming' the other side.
Get the car plenty high enough and use a jack & some pieces of wood across the chassis members so you don't get stuck holding the diff up. It's manageable when you are ready... but the dead weight can catch you out if you aren't prepared.
The rear mount (bush) can be undone easily enough through the wheel arches just using rather a lot of extension bars and a suitable spanner 'jamming' the other side.
Get the car plenty high enough and use a jack & some pieces of wood across the chassis members so you don't get stuck holding the diff up. It's manageable when you are ready... but the dead weight can catch you out if you aren't prepared.
spend said:
Plenty of diffs have to be shoved quite a long way forward to get out, due to the various rear covers (particularly GKNs). Prop shaft can certainly prevent some diffs coming out, but also pushing forward so that the fore chassis xmember takes some of the weight whilst you twist the diff 90degs and then lower the rear is my preferred routine.
The rear mount (bush) can be undone easily enough through the wheel arches just using rather a lot of extension bars and a suitable spanner 'jamming' the other side.
Get the car plenty high enough and use a jack & some pieces of wood across the chassis members so you don't get stuck holding the diff up. It's manageable when you are ready... but the dead weight can catch you out if you aren't prepared.
Thanks for that, I have just identified it as a GKN, I like Quinny's method of various straps to lower it.The rear mount (bush) can be undone easily enough through the wheel arches just using rather a lot of extension bars and a suitable spanner 'jamming' the other side.
Get the car plenty high enough and use a jack & some pieces of wood across the chassis members so you don't get stuck holding the diff up. It's manageable when you are ready... but the dead weight can catch you out if you aren't prepared.
Since it is a GKN, take your time removing the prop so that you know how the speedo trigger and sensor brackets go back together. The sensor wiring may be siliconed to the sensor so you have to trace all the way up the trans tunnel to find a connector, be warned it's a nightmare to have to go back in later to fix a dodgy speedo connection 
Make sure you have some imperial hex sockets, those capheads on the front of the diff carriers are torqued up pretty high. The outside chassis bolts on the carriers can be bit of a PITA on early cars as they are much longer if you have the 'floating' side bush style. Patience is key, I'd advise cracking all the bolts then taking some rest & respite before manhandling the diff out. It is of course a doddle the second time around when you know exactly what you are doing and have nicely copper slipped all the fasteners.

Make sure you have some imperial hex sockets, those capheads on the front of the diff carriers are torqued up pretty high. The outside chassis bolts on the carriers can be bit of a PITA on early cars as they are much longer if you have the 'floating' side bush style. Patience is key, I'd advise cracking all the bolts then taking some rest & respite before manhandling the diff out. It is of course a doddle the second time around when you know exactly what you are doing and have nicely copper slipped all the fasteners.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



.
t of a job 

