Ticking Noise - Any Suggestions....
Ticking Noise - Any Suggestions....
Author
Discussion

andy-w

Original Poster:

1,987 posts

257 months

Monday 4th October 2010
quotequote all
Hi guys,

I have a ticking noise that was feint on friday driving home.
I never used the car over the weekend but checked plugs and manifold bolts and all seemed ok. Driving in to work today the sound was still there but after 2 miles and the engine got a bit warmer it sounded a lot louder, especially under load.

Just wondering if anyone has got any ideas or pointers apart from exhaust gaskets.

It seems to be comming from the rear drivers side but sounds closer to the plenum than exhaust???

The car has oil and seems to be running fine apart from sounding like a skeleton having a wcensored in a biscuit tin...!!!

Tyre Tread

10,697 posts

247 months

Tuesday 5th October 2010
quotequote all
possible one of the pads has come off the rocker.

Dave 500

7,889 posts

273 months

Tuesday 5th October 2010
quotequote all
I would nip up the exhaust manifold bolts first smile

LordGrover

34,190 posts

243 months

Tuesday 5th October 2010
quotequote all
Dave 500 said:
I would nip up the exhaust manifold bolts first smile
yes If that doesn't do it I'd check the exhaust manifold gaskets, look for sooty deposits.

Edited by LordGrover on Tuesday 5th October 09:20

spend

12,581 posts

282 months

Tuesday 5th October 2010
quotequote all
Use a pipe to your ear to listen for exhaust leaks and a piece of wood for mechanical noises (big screwdrivers are too clanky IMHO). Just keep clear of the twirly belts and its safe/easy enough to track down a little further. Many of the noises change with load/rpms you can at least pull the throttle lever to get rpms but load is quite difficult unless you have a rolling road.

I always feel a tad disconcerted with the 'nip up the manifold bolts' idiom? Fine if they are loose.., but I suspect more head tappings are wrecked / flanges distorted / gaskets ground into submission than any problems fixed in many cases.

slideways

4,101 posts

252 months

Tuesday 5th October 2010
quotequote all
I've got the same thing on my P38 i think it could be a lazy follower as it comes and goes without changing the rpm's, i will get round to checking it one of these days

andy-w

Original Poster:

1,987 posts

257 months

Tuesday 5th October 2010
quotequote all
hi guys,

I did try the bolts as the easy option first and it is still there it sounds almost like air escaping from a balloon but with a bit of a bass roar to it, i know it is impossible to describe a sound...i have it recorded and need to get it posted somewhere to share it...!

I dont think it is a rocker problem as it seems to slow its in beat with the engine revs, one full turn one noise...if it were rocker related then surely it would be twice the speed...?

Going to do a compression test on all 8 pots tonight, listen with various bits of wood and tube, drain oil and look for metal and if there is nothing conclusive i have already ordered a full set of gaskets and it is time to do a top end strip....!

The noise has not got any worse and it happened in the space of about 2 miles of normal gentle driving.

Good thing so far is the water level has not dropped much and there is no mayo in the filler cap...!

Other things i were thinking were holed piston, big end bearing or rings?

Other thing i was going to look at tonight out of curiosity does the ful pump run at a constant pressure to keep up with demand or does it pulse?

Edited by andy-w on Tuesday 5th October 11:57

Alexdaredevilz

5,697 posts

210 months

Tuesday 5th October 2010
quotequote all

spend

12,581 posts

282 months

Tuesday 5th October 2010
quotequote all
andy-w said:
Other thing i was going to look at tonight out of curiosity does the ful pump run at a constant pressure to keep up with demand or does it pulse?
Whilst engine running the pump just runs full bore... The fuel pressure regulator does what it says in the name.

Lot of diagnostic headaches are caused by the fuel pump priming cycle, but its really a safety feature so that if the engine stops (like a crash etc.) the pump stops.

Manifold gaskets seem to get worse with load, but small bore pipe to your ear is very sensitive to hear leaks even at tickover. Don't forget it could be the collector or even Y-piece joints when scanning. Quite likely some tt made a mess of installing the gaskets at some stage winkhehe

deeen

6,413 posts

276 months

Tuesday 5th October 2010
quotequote all
Spend just reminded me, my Y-piece needed welding when it was ticking, i was told quite common.

andy-w

Original Poster:

1,987 posts

257 months

Tuesday 5th October 2010
quotequote all
yes it does sound like that underload but quite a bit louder...

i should have done what you did and video'd it before ripping bits and peices off...think i might video it tonight and post it on YT...

at least then you can hear what it sounds like

Alexdaredevilz

5,697 posts

210 months

Tuesday 5th October 2010
quotequote all
andy-w said:
yes it does sound like that underload but quite a bit louder...

i should have done what you did and video'd it before ripping bits and peices off...think i might video it tonight and post it on YT...

at least then you can hear what it sounds like
Mine was louder in the car than it shows on the video, i had to take manifolds off, and grind/rub off the crap so i could get it flat to the block, new gaskets jobs a good un,

P.s i drilled the pre cats out aswell whilst i was there

Alex

andy-w

Original Poster:

1,987 posts

257 months

Tuesday 5th October 2010
quotequote all
spend said:
Quite likely some tt made a mess of installing the gaskets at some stage winkhehe
you KNOW i was the last person to put the manifolds on when i did my body off lift a couple of years back.... whistle

As for the pre cats they fell out a few years ago....!

Edited by andy-w on Tuesday 5th October 13:19

spend

12,581 posts

282 months

Tuesday 5th October 2010
quotequote all
...always a bugger when you can't blame anyone else rofl

andy-w

Original Poster:

1,987 posts

257 months

Tuesday 5th October 2010
quotequote all
spend said:
...always a bugger when you can't blame anyone else rofl
no - its always a bugger when somebody brings up the point that what could be at fault is what someone has done themselves to create that fault and they cant blame anyone else....

spend

12,581 posts

282 months

Tuesday 5th October 2010
quotequote all
At least the 'buggers' might advise you not waste your time stripping top end down & sump off, before making absolutely sure it's not simply a leaky exhaust hehe

andy-w

Original Poster:

1,987 posts

257 months

Tuesday 5th October 2010
quotequote all
ok so if putting a hose down past the very rear drivers side exahust manifold it nearly blows your eardrum out would this indicate some kind of others were silent and made no difference as to where i put the tube around them but the rear (no 8) was deafening...

Got new gaskets on order so they should be here tomorrow and will do a compression test as well just to double check nothing is amiss

Tyre Tread

10,697 posts

247 months

Tuesday 5th October 2010
quotequote all
andy-w said:
I dont think it is a rocker problem as it seems to slow its in beat with the engine revs, one full turn one noise...if it were rocker related then surely it would be twice the speed...?

Edited by andy-w on Tuesday 5th October 11:57
No as the follower for each of the valves only opens once per cycle. Therefore the follower on number 1 inlet only opens once for each revolution of the engine.

V8 Developments told me its quite common for the RV8 to drop the pads which end up in the sump.

I need to look at mine with similar problem.

andy-w

Original Poster:

1,987 posts

257 months

Tuesday 5th October 2010
quotequote all
i honestly thought the vales open twice each revolution...not sure why i thought that, i guess a moment of madness...!!!

Well i have taken both the manifolds off...one on the near side had a trace of blowing, it had carbon/soot around it and as for the rear drivers side...one came of intact and the other came off in pieces and there is about 15mm missing!!!

I think i know what the problem might be.... wink

Bassfiend

5,530 posts

281 months

Tuesday 5th October 2010
quotequote all
Tyre Tread said:
No as the follower for each of the valves only opens once per cycle. Therefore the follower on number 1 inlet only opens once for each revolution of the engine.
As it's a four-stroke engine then surely each valve opens once every other rotation/revolution?

Phil