Rev Counter
Rev Counter
Author
Discussion

fog66

Original Poster:

368 posts

229 months

Wednesday 13th October 2010
quotequote all
I've been changing the veneer on the dash for something a bit more modern and in doing so I noticed when I disconnected the rev counter at the rear there is a light which is not connected. It looks like it illuminates a red rectangular light on the rev counter however the cable is attached to the bulb but the other end is just tied up and not connected. Is this a rev limiter/warning light and if so was it optional (which maybe why it's not connected) or was it connected as standard and has been disconnected by a previous owner? If it is meant to be connected how do I find the connectors? Cheers for any info.

Alexdaredevilz

5,697 posts

210 months

Thursday 14th October 2010
quotequote all
I done my dash last week I found a few like that, turns out the wiring connectors fell off , found the broken wires, new spade connector and was good as new

John042

904 posts

200 months

Thursday 14th October 2010
quotequote all
Hi fogg66, I seem to remember in a previous post that it was an optional gear change indicator light? How did you get on with re-veneering your dash? I've got a chap whose willing to have a 'crack' at it, either replacing the veneer or even making a complete wooden one. Which would, I guess, negate the chance of future cracking. Are there firms who will re-veneer your dash and what's the likely cost? Cheers John042

Cider Andy

1,889 posts

256 months

Thursday 14th October 2010
quotequote all
It's a gear change warning lamp, not used in the Chimaera, but the same rev counter is used in the Cerbera, where the lamp is connected.

I used it as a warning lamp for the fan override.

Cider Andy

1,889 posts

256 months

Thursday 14th October 2010
quotequote all
John042 said:
...I've got a chap whose willing to have a 'crack' at it, either replacing the veneer or even making a complete wooden one. Which would, I guess, negate the chance of future cracking. Are there firms who will re-veneer your dash and what's the likely cost?...
I had mine re-veneered a few years ago by a mandolin maker. I think it cost around £250 for both panels and, as he hadn't applied a veneer to mild steel before, it took a bit of trial and error with different adhesives. The finished product was fantastic and included around 25 coats of lacquer. Unfortunately the car spent the subsequent winter months with the roof panel not properly fitted and the resultant damp caused it to start peeling again.

At the moment I'm making two new sets of panels. One will be the original steel panels in carbon fibre; the other will be burr walnut veneer again, but on a 2mm MDF backing. Going much thicker than that would cause problems refitting it: the support brackets would need modifying, the main panel would need a curve in it and the radio panel would be difficult to fit properly, it being surface mounted.

The firm that springs to mind that will re-veneer the panels is London Carriage Craft. Over the years I've read of quite a few owners on here that have been happy with their work.

John042

904 posts

200 months

Thursday 14th October 2010
quotequote all
Thankyou Cider Andy, I'll shop around. I might consider covering the dash with a carbon fibre, not sure of the efect or cutting around instruments etc. Cheers John042

fog66

Original Poster:

368 posts

229 months

Thursday 14th October 2010
quotequote all
John042 said:
Hi fogg66, I seem to remember in a previous post that it was an optional gear change indicator light? How did you get on with re-veneering your dash? I've got a chap whose willing to have a 'crack' at it, either replacing the veneer or even making a complete wooden one. Which would, I guess, negate the chance of future cracking. Are there firms who will re-veneer your dash and what's the likely cost? Cheers John042
I didn't re veneer, I'm using a carbon effect wrap. Looks good so far, I've completed and installed the radio panel and I'll be finishing the main dash at the weekend. Fingers crossed scratch free!
Looks like the light doesn't need to be connected, cheers.

John042

904 posts

200 months

Thursday 14th October 2010
quotequote all
Hi fog66, I'm considering carbon fibre wrap but my interior is the light cream leather with magnolia dials!! What colour interior is yours? Could you supply a pic on the finished project? What's carbon fibre wrap like to work with and supply source? Thanks for any advice. John042

fog66

Original Poster:

368 posts

229 months

Thursday 14th October 2010
quotequote all
I'll Put a picture on tomorrow and tell you about the wrap stuff.

fog66

Original Poster:

368 posts

229 months

Friday 15th October 2010
quotequote all
Project so far..........


Cider Andy

1,889 posts

256 months

Friday 15th October 2010
quotequote all
Canny tunes tho' but! biggrin

fog66

Original Poster:

368 posts

229 months

Friday 15th October 2010
quotequote all
Cider Andy said:
Canny tunes tho' but! biggrin
Well I had to give it a thorough test!

fog66

Original Poster:

368 posts

229 months

Friday 15th October 2010
quotequote all
The wrap stuff I used was a 3M product. It's quite thick and covers minor surface damage very well. It doesn't bubble unless you do something majorly dumb. Once it's applied to the main surface you just use a hairdryer or heat gun a d mold it around, stick and trim. Voilà.

John042

904 posts

200 months

Friday 15th October 2010
quotequote all
Very impressive fog66. Against red, but, I wonder with pale tan? Does it come in different shades and from which supplier. The curved main panel fills me with concern not only with size but being 'in your face' all the time. Was it easy to apply,trim and did you use a compact glue? Thanks John042

fog66

Original Poster:

368 posts

229 months

Saturday 16th October 2010
quotequote all
John042 said:
Very impressive fog66. Against red, but, I wonder with pale tan? Does it come in different shades and from which supplier. The curved main panel fills me with concern not only with size but being 'in your face' all the time. Was it easy to apply,trim and did you use a compact glue? Thanks John042
This wrap stuff is self adhesive, a but like old school fablon. As long as you take your time it's really quite easy. Your interior sounds like biscuit? I think the stuff I've used only comes in black or White from the supplier I'm using (he's local to me in Newcastle upon Tyne) his business is vinyl signing. I got the two bits I've used FOC as they were off cuts but it costs £52 per metre. Why not post a picture of your current interior and we can assess how it might look, all on our own opinion if course. Phil.

fog66

Original Poster:

368 posts

229 months

Saturday 16th October 2010
quotequote all
Nearly finished....





Edited by fog66 on Saturday 16th October 16:49

John042

904 posts

200 months

Sunday 17th October 2010
quotequote all
Thanks fog66 (Phil) very impressive against a darker surround. Unfortunately my beast is in dis-array steering wheel of bits of trim etc so a pic might not be much use. The leather trim is cream (Magnolia?) a dark covered dash might not be the answer. Veneering might be the only course of action? Thanks again for the info and pics. Cheers John042.