double up on the exhaust gasket, good or bad idea
double up on the exhaust gasket, good or bad idea
Author
Discussion

Kwacker

Original Poster:

641 posts

315 months

Wednesday 13th October 2010
quotequote all

I'm just about to put the exhaust back together and was wondering if it would be a good or a bad idea to double up the gaskets?

Thoughts please, no post cards.

Kwacker

Alexdaredevilz

5,697 posts

210 months

Wednesday 13th October 2010
quotequote all
Bad idea

AREA

497 posts

256 months

Wednesday 13th October 2010
quotequote all
A gasket is there to provide a seal between two surfaces. Using two gaskets creates another two surfaces that have to seal, and equally could fail. Personally I don't see why it would be a good thing.

But I'm intrigues - what's the problem that you're trying to solve through two gaskets?

pwd95

8,459 posts

269 months

Wednesday 13th October 2010
quotequote all
Mine wouldn't seal untill I used two gaskets. It'll save you taking it all apart again to use two gaskets. Deffo good idea. thumbup

neal1980

2,585 posts

270 months

Thursday 14th October 2010
quotequote all
Just to jump in, whats the best gaskets to use these days??

Got a set with a complete gasket set but they dont look great to me and there all single so probably a right bh to fit.

Thanks

Neal

SILICONE KID

14,997 posts

262 months

Thursday 14th October 2010
quotequote all
This is the stuff you need.PERMATEX
http://www.permatex.com/products/automotive/automo...


Edited by SILICONE KID on Thursday 14th October 15:29

Kwacker

Original Poster:

641 posts

315 months

Thursday 14th October 2010
quotequote all
Going to go for single gaskets. Hope it works. All has gone very smoothly so far, no grazed knuckles. Just a bit time consuming.

Kwacker

Meatball

1,638 posts

241 months

Thursday 14th October 2010
quotequote all
V8D gaskets with high temp silicone - not your standard plumbers stuff wink

Kwacker

Original Poster:

641 posts

315 months

Thursday 14th October 2010
quotequote all
Well everything went back together very well, I was only left with one lock washer spare.

Starter motor was being a bit of a sod, It sounded as though it was engaging but not turning the engine. After repeated attempts it finally started.

AND...

The exhaust gasket is still blowing. Either I used the wrong gasket or they were slightly out of position.

This time I think I will swap out the starter motor and use better gaskets with a smear of that silicone/compound.

Back to square one. At least I know what I'm doing this time!

Kwacker

Alexdaredevilz

5,697 posts

210 months

Thursday 14th October 2010
quotequote all
Sounds like you got crap on the block or manifold. Dud you clean it all up?

Or you got a gasket the wrong way round easy done

Also check your manifolds aren't cracked

SILICONE KID

14,997 posts

262 months

Thursday 14th October 2010
quotequote all
Fill the manifolds with water and watch it leak out the four in to one.furiousThen change your engine mounts!

Chimpaholic

9,637 posts

210 months

Friday 15th October 2010
quotequote all
Quinny said:
I'd use a single gasket, but with a smear of silicon either sidesmile
That's how I did it, absolutely no leaks.

I used the ACT kit, you get:

1) Large port metalised composite gaskets

2) 1 set of ARP stainless bolts

3) 1 set of Nordlock locking washers

I spent a lot of time cleaning the head & manifold faces, like most jobs preparation is key.

Finally a very thin smear of Permatex very high temp silicone on both faces of the gasket for good measure.

I checked the bolt tightness after 500 miles and they were all as tight as when I fitted them, the Norlock washers definitely work.

5,000 miles since I did the job and absolutely no leaks.