Winter odd-jpb plans......
Winter odd-jpb plans......
Author
Discussion

Nosh

Original Poster:

982 posts

198 months

Wednesday 13th October 2010
quotequote all
Clocks are a changin'....

Fewer evenings to go for a blatt after a hard 9-5 slog...

Less weekends for a leisurley drive with SWMBO....

All that 'spare' time....

I intend to clean up all the earthing points...
Rocker cover gasket change (noticed a little oil seeping out)
Interior - dash and perhaps carpets....

So what are you planning in the cold winter evenings and weekends to come?

Nosh

dogbucket

1,256 posts

232 months

Wednesday 13th October 2010
quotequote all
Do some rust proofing on the center parts of the chassis that I have not got to before.

Maybe replace rad that has always leaked a tiny bit.

Maybe swap dash for Leven one if I can get hold of one.




Jonny cobra

615 posts

243 months

Wednesday 13th October 2010
quotequote all
I will mostly be replacing the rest of my suspension bushes , And painting my calipers, Probably some other bits also.



JC

Robatr0n

12,362 posts

247 months

Wednesday 13th October 2010
quotequote all
Bloody show off! hehe

450Nick

4,027 posts

243 months

Wednesday 13th October 2010
quotequote all
Hmmm odd jobs eh?

Well I've got a few bits and bobs to take care of...

- Replace rear wheel bearing
- Sort out a weeping power steering hose
- Fix the rattley passenger window once and for all
- Replace the knackered speedo LED which went yesterday
- Respray
- Finally fit the mk3 lights which have been sitting attached to the car with nothing but the headlight wires for A YEAR
- Replace the window seals and hoop seal
- Fit a MAP sensor to my ECU and have it remapped

Then the small matter of wiring up and putting an engine in the Tuscan racer and making that move under its own steam along with a million other little things it needs... Its going to be a long winter!

hiltonig

3,153 posts

239 months

Thursday 14th October 2010
quotequote all
Ahh 450nick, do you have a pic of the heat shields around the supercharger and dump valve ?, i have the S/C kit fitted with the ACT manifolds as per yours and need to see what you have done with regards to heat shielding.

spend

12,581 posts

282 months

Thursday 14th October 2010
quotequote all
Nosh said:
Rocker cover gasket change (noticed a little oil seeping out)
If you are doing it over the winter, check very carefully that the valley gasket / end seals are not the culprit.

450Nick

4,027 posts

243 months

Thursday 14th October 2010
quotequote all
hiltonig said:
Ahh 450nick, do you have a pic of the heat shields around the supercharger and dump valve ?, i have the S/C kit fitted with the ACT manifolds as per yours and need to see what you have done with regards to heat shielding.
Hi Nigel

I don't have a pic on me at the moment but I can try and get one over the weekend when I'm at home. IIRC, the offside side around the recirc valve wasn't a problem at all and it all fits as standard. The nearside with the modified SC manifold was a bit more of a challenge and I had to cut a square-ish section out of the top of the heat sheild at the very end (nearest the bonnet) as the bend kicks up too early and hits the sheild. It still protects the charger etc no problem, but the top stops shorter than normal (the side bit continues to sheild the intake pipe as much as possible).

I then had to slightly bend the mounting bit up to lift the whole sheild up by 1-2 mm to get a little more clearance over the manifold than normal, and I think there may have been a small amount of bending to clear the manifold ports. It sounds like a lot but it wasn't really. I just cut the top out to clear the major difference and the rest was done with a long screwdriver as and when I detected a buzz from the sheild!

neal1980

2,585 posts

270 months

Thursday 14th October 2010
quotequote all
Im planning to finally finish this now ready for April..Got my winter warmers ready no excuses now smile









Edited by neal1980 on Thursday 14th October 11:49

haircutmike

22,511 posts

235 months

Thursday 14th October 2010
quotequote all
neal1980 said:
Im planning to finally finish this now ready for April..Got my winter warmers ready no excuses now smile









Edited by neal1980 on Thursday 14th October 11:49
Tell us more!

Alexdaredevilz

5,697 posts

210 months

Thursday 14th October 2010
quotequote all
TVR list

Decat Y-piece
Change Spark plugs
Adjust windows and lube
Make new washer jet system
Smooth bore pipe mod
Sort AF ratio out

Race mower list

Weld front end + steering
Mount seat
Rebuild engine
Make clutch system
Paint





darkcat

2,354 posts

201 months

Thursday 14th October 2010
quotequote all
tvr-
rear wheel bearing (got ready to go)
engine mounts (got ready to go)
manifold gaskets (got ready to go)
rocker cover gaskets (got ready to go)
find the weird whistling from the plenum area
find the annoying knocking from the rear!!!!
full geometry

Mini-
build chassis
attach body to chassis
mount engine + gearbox
mount bonnet/wing thing
build front suspension
prep for IVA test
re-thing things after failing IVA
give in and go to the pub.

haircutmike

22,511 posts

235 months

Thursday 14th October 2010
quotequote all
I've started already!

Car on axle stands awaiting delivery of rebuilt diff and rack tomorrow.

Recarpet interior.
Bit of reupholtery works.
Sell road wheels and tyres, (gonna run on wider, "Image" track wheels and tyres all the time).
Change Pro-Tech dampers for something a little more hardcore.
Do away with mesh grill but fit another mesh grill deeper in front of oil cooler and rad for protection.

Alexdaredevilz

5,697 posts

210 months

Thursday 14th October 2010
quotequote all
I call first dibs on shocks

ralphy12345

330 posts

196 months

Thursday 14th October 2010
quotequote all
Winter odd-jobs? Hah! Since I got mine two months ago it's been a non-stop project laugh and I'm resigned to it taking me through to Easter...........
currently looking like this:


It's been a steep learning curve so far and, whilst I'm enjoying it overall, some of the workmanship I've come across (rear of the dashboard springs to mind hehe) has been a real eye-opener......................

R

hiltonig

3,153 posts

239 months

Friday 15th October 2010
quotequote all
I would love to ask how to get the dash top off as my speedo bulb has gone

darkcat

2,354 posts

201 months

Friday 15th October 2010
quotequote all
hiltonig said:
I would love to ask how to get the dash top off as my speedo bulb has gone
you need the fingers of a ninja and the knuckles of iron man. and you need to be a contortionist.
do a search! not "easy" but not hard.

i took mine off and tbh havent bothered to re-attach properly

450Nick

4,027 posts

243 months

Friday 15th October 2010
quotequote all
darkcat said:
hiltonig said:
I would love to ask how to get the dash top off as my speedo bulb has gone
you need the fingers of a ninja and the knuckles of iron man. and you need to be a contortionist.
do a search! not "easy" but not hard.

i took mine off and tbh havent bothered to re-attach properly
bks...! Sit in the right position and you can have it off in 3 minutes with unscathed hands (same as the door cards). biggrin

haircutmike

22,511 posts

235 months

Friday 15th October 2010
quotequote all
hiltonig said:
I would love to ask how to get the dash top off as my speedo bulb has gone
Nigel.

Remove elasticated handbook holder flap.

Look up into void, remove 10mm bolt that is looking upwards.

You can then lift the dash top up about 10" and get to most things.

If you want to remove the whole top, there is a bolt on the drivers side in a similar position.

A swan's neck and a 10mm ratchet spanner make work easy!

P.

darkcat

2,354 posts

201 months

Friday 15th October 2010
quotequote all
haircutmike said:
hiltonig said:
I would love to ask how to get the dash top off as my speedo bulb has gone
Nigel.

Remove elasticated handbook holder flap.

Look up into void, remove 10mm bolt that is looking upwards.

You can then lift the dash top up about 10" and get to most things.

If you want to remove the whole top, there is a bolt on the drivers side in a similar position.

A swan's neck and a 10mm ratchet spanner make work easy!

P.
...and the one at the back on the passenger side......