play in transmission... where to start
play in transmission... where to start
Author
Discussion

darkcat

Original Poster:

2,354 posts

201 months

Thursday 14th October 2010
quotequote all
I seem to have developed some play in the transmission, i.e between power on and power off, there appears to be play in the prop/drive shafts / diff.
now i KNOW the diff is not loose, so what could be wrong? im told that the UJ's on the prop are OK too...

i REALLY HOPE its not a diff problem...

anyone spare a sunday afternoon to have a look?

450Nick

4,027 posts

243 months

Thursday 14th October 2010
quotequote all
I would wager you have worn CV's... Not cheap to replace but I snapped a drive shaft a little while ago and replaced both CVs and the shaft on one side and about half of my drivetrain backlash has dissappeared.. Just got to do the other side now but at £400 a side its a bit much at the moment!

darkcat

Original Poster:

2,354 posts

201 months

Thursday 14th October 2010
quotequote all
£400 EACH??????????? holy F*******

sounds something like that, i'll keep an eye out on ebay... and drive carefully!

450Nick

4,027 posts

243 months

Thursday 14th October 2010
quotequote all
darkcat said:
£400 EACH??????????? holy F*******

sounds something like that, i'll keep an eye out on ebay... and drive carefully!
Each side... This was £90 each for the CVs (2 each side), £200ish for the new driveshaft and a few quid for CV grease etc. I'm sure you won't need new driveshafts unless you've snapped them so more like £200 a side + labour if you don't want to do it yourself.

hiltonig

3,153 posts

239 months

Friday 15th October 2010
quotequote all
Did you go for the race approved ones Nick ?.

450Nick

4,027 posts

243 months

Friday 15th October 2010
quotequote all
hiltonig said:
Did you go for the race approved ones Nick ?.
Nah, I couldn't justify the extra cost when mine lasted that long without any problems. As far as I can tell, the standard ones are fine to take the power (I've done plenty of track work and plenty of hard starts on R888's and they've been fine). Mine went at about 10 miles an hour, going round a mini roundabout in 3rd gear which would have been well within the amount of torque that a standard engine can produce at that point. So it wasn't excess torque that killed it, I suspect just fatigue though this is perfectly possible on a standard car as well. If I break the replacement then perhaps I'll uprate it... Trying to put all funds into the racer at the moment though so the Chim isn't getting the usual royal treatment it usually gets!

Edited by 450Nick on Friday 15th October 10:05

haircutmike

22,511 posts

235 months

Friday 15th October 2010
quotequote all
darkcat said:
I seem to have developed some play in the transmission, i.e between power on and power off, there appears to be play in the prop/drive shafts / diff.
now i KNOW the diff is not loose, so what could be wrong? im told that the UJ's on the prop are OK too...

i REALLY HOPE its not a diff problem...

anyone spare a sunday afternoon to have a look?
You say the diff isn't loose.

My rear mount bracket that bolts to the diff with 4 X cap bolts became loose and made a huge clonking during power on & off.

These are a b*stard to do up, worth a check, take a wheel off and get your arm in there with an Allen key!

darkcat

Original Poster:

2,354 posts

201 months

Friday 15th October 2010
quotequote all
haircutmike said:
darkcat said:
I seem to have developed some play in the transmission, i.e between power on and power off, there appears to be play in the prop/drive shafts / diff.
now i KNOW the diff is not loose, so what could be wrong? im told that the UJ's on the prop are OK too...

i REALLY HOPE its not a diff problem...

anyone spare a sunday afternoon to have a look?
You say the diff isn't loose.

My rear mount bracket that bolts to the diff with 4 X cap bolts became loose and made a huge clonking during power on & off.

These are a b*stard to do up, worth a check, take a wheel off and get your arm in there with an Allen key!
i know its not loose because i tightened it! yes the are a pain to get to, i went for the "from the bottom" approach.

haircutmike

22,511 posts

235 months

Friday 15th October 2010
quotequote all
darkcat said:
haircutmike said:
darkcat said:
I seem to have developed some play in the transmission, i.e between power on and power off, there appears to be play in the prop/drive shafts / diff.
now i KNOW the diff is not loose, so what could be wrong? im told that the UJ's on the prop are OK too...

i REALLY HOPE its not a diff problem...

anyone spare a sunday afternoon to have a look?
You say the diff isn't loose.

My rear mount bracket that bolts to the diff with 4 X cap bolts became loose and made a huge clonking during power on & off.

These are a b*stard to do up, worth a check, take a wheel off and get your arm in there with an Allen key!
i know its not loose because i tightened it! yes the are a pain to get to, i went for the "from the bottom" approach.
I did that from below and it loosened again, you can't get enough purchase.

They should be torqued to about 30-34 ft/lbs with thread lock applied.

Took my fuel tank out to do the job properly!

darkcat

Original Poster:

2,354 posts

201 months

Friday 15th October 2010
quotequote all
haircutmike said:
I did that from below and it loosened again, you can't get enough purchase.

They should be torqued to about 30-34 ft/lbs with thread lock applied.

Took my fuel tank out to do the job properly!
yes i made an access hole behind the tank too ;-)

anyway - cant be that. totally different sound/feel

haircutmike

22,511 posts

235 months

Friday 15th October 2010
quotequote all
darkcat said:
haircutmike said:
I did that from below and it loosened again, you can't get enough purchase.

They should be torqued to about 30-34 ft/lbs with thread lock applied.

Took my fuel tank out to do the job properly!
yes i made an access hole behind the tank too ;-)

anyway - cant be that. totally different sound/feel
Good man, just checking wink