Powder coating plenum
Powder coating plenum
Author
Discussion

SILICONE KID

Original Poster:

14,997 posts

262 months

Saturday 16th October 2010
quotequote all
After having the rocker covers powder coated in satin black they look fantastic.Im now thinking of doing the same thing with the plenum.Would there be a problem absorbing heat as we all know this is our enemy.Thanks

roysum

961 posts

220 months

Saturday 16th October 2010
quotequote all
SILICONE KID said:
After having the rocker covers powder coated in satin black they look fantastic.Im now thinking of doing the same thing with the plenum.Would there be a problem absorbing heat as we all know this is our enemy.Thanks
Personally I don't think it would make much difference under a bonnett.

chimaera1855

334 posts

199 months

Sunday 17th October 2010
quotequote all
u should do it as well!!!i did and now the temperature under the bonnet is much cooler.

Barkychoc

7,848 posts

235 months

Sunday 17th October 2010
quotequote all
Done mine Daz, cost a tenner I think at powder coaters at Cropwell Bishop not far from Langar. I stripped and cleaned it first. Currently typing on phone will post a pic later if you want and contact details.

SILICONE KID

Original Poster:

14,997 posts

262 months

Sunday 17th October 2010
quotequote all
I had mine done by Wheel Works Nottinham,charged me 20 pounds for both rocker covers.They sand blasted then powder coated and put in a oven.Is it simple enough to remove the bit off the plenum.

BliarOut

72,863 posts

270 months

Sunday 17th October 2010
quotequote all
i was about to ridicule you, but a 'proper' heat reflecting coating, not paint!! may help keeping the induction temps down.

spend

12,581 posts

282 months

Sunday 17th October 2010
quotequote all
Insulation coating needs to go on the surface next to the air / charge in that case, and a heat shedding coating on the outer surface... Bling & tuning require totally different approaches hehe

The gains from heat management of the induction can be misconstrued due to most of the available data being from RR sessions though? Taking care to consider the different impacts on RR's and traffic light GP's compared to say running in free air at a constant 5000rpm gives quite different scenarios.

Pupp

13,037 posts

303 months

Sunday 17th October 2010
quotequote all
Another thing to consider with coating the internal of the plenum is what happens to the material when it starts to flake and drop off. Trust me, it will wink

spend

12,581 posts

282 months

Sunday 17th October 2010
quotequote all
Pupp said:
Another thing to consider with coating the internal of the plenum is what happens to the material when it starts to flake and drop off. Trust me, it will wink
I trust you have the same disregard for coated pistons & valves then?

SILICONE KID

Original Poster:

14,997 posts

262 months

Sunday 17th October 2010
quotequote all
Now its getting complicated.Im aware that the colour or shade black absorbs heat,so would it make much difference.It does look prity in satin black .

BliarOut

72,863 posts

270 months

Sunday 17th October 2010
quotequote all
SILICONE KID said:
Now its getting complicated.Im aware that the colour or shade black absorbs heat,so would it make much difference.It does look prity in satin black .
'Proper'...

SILICONE KID

Original Poster:

14,997 posts

262 months

Sunday 17th October 2010
quotequote all
?eek

rigga

8,808 posts

232 months

Sunday 17th October 2010
quotequote all
Actually black may not be that heat absorbing as you think..... i remember a while back on the Subaru forums a topic regarding the reason the sti intercoolers were painted silver over the standard cars black versions,as it turned out someone who had done some thermal testing revieled that the better colour to have which didnt absorb as much temp was in fact the black ones,the sti ones just looked prettier ...... make of that what you will.

Jon Brown

681 posts

215 months

Sunday 17th October 2010
quotequote all
Im very interested in this, anyone have any pics??

Pupp

13,037 posts

303 months

Sunday 17th October 2010
quotequote all
spend said:
Pupp said:
Another thing to consider with coating the internal of the plenum is what happens to the material when it starts to flake and drop off. Trust me, it will wink
I trust you have the same disregard for coated pistons & valves then?
laugh I might trust the likes of Messrs Wiseco, Cosworth, Manley et al to maybe make a better job of it than some bloke with an epoxy powder line more used to handling pram tubing and clothes horses but even Tefal pans lose their teflon eventually...