remove the butterfly
remove the butterfly
Author
Discussion

SILICONE KID

Original Poster:

14,997 posts

262 months

Wednesday 20th October 2010
quotequote all
Hello.I have removed all the bits off the plenum.Hope they go back in orderidea
How do i remove the butterfly and the shaft thing as they have rubber seals.I don`t want to melt them in the oven after powder coating.Do you think the plenum will be ok being powder coated or shell i get it painted.
don`t want it to warp
confused

Barkychoc

7,848 posts

235 months

Wednesday 20th October 2010
quotequote all
Undo the 2 small screws that hold the butterfly to the shaft Daz, pull the butterfly out of the shaft through the end of the plenum, then the shaft pulls out.

I marked mine up with marker pen before removing it so I knew how to reassemble it again.

YHM by the way

SILICONE KID

Original Poster:

14,997 posts

262 months

Wednesday 20th October 2010
quotequote all
Looks bit of a swine to re fit the butterfly.Is there any chance of it warping in the oven.eekCan i leave the heat exchanger off,Its not doing anything.

Edited by SILICONE KID on Wednesday 20th October 20:27

v8 racing

2,064 posts

282 months

Wednesday 20th October 2010
quotequote all
daz just quickly dont forget you are going to need to reset the throttle pot in the megasquirt software or it will run like a dog....

SILICONE KID

Original Poster:

14,997 posts

262 months

Wednesday 20th October 2010
quotequote all
Throttle pot?Nothing is going to be adjusted ,put back how it was.

Ant.

5,254 posts

312 months

Wednesday 20th October 2010
quotequote all
SILICONE KID said:
Throttle pot?Nothing is going to be adjusted ,put back how it was.
roflrofl Will he ever fking learn??????

Daz, leave it alone, you fked it up before, please for your sanity, Robs and ours either leave it alone or start to listen !!!!!!

SILICONE KID

Original Poster:

14,997 posts

262 months

Wednesday 20th October 2010
quotequote all
please explain.eek.thought it would be a simple job.Its all in bits now.

Ant.

5,254 posts

312 months

Wednesday 20th October 2010
quotequote all
SILICONE KID said:
please explain.eek.thought it would be a simple job.Its all in bits now.
Right, just for you our 'lil fiddler......


The software in your ECU will be set up for a min/max value feedback from your TPS (the"load" part of your maps), now you have taken it all apart the chances of it going back in exactly the same way is minimal. Therefore, when the plenum is re-assembled and re-fitted to the engine the min/max values will need to be re-learnt into the ECU..


Do you know how to do this??????????





ETA, Daz , no matter how much st you generate/take you always come back, in a frustrating way, hats off to ya....

slideways

4,101 posts

252 months

Wednesday 20th October 2010
quotequote all
coffee

Meatball

1,638 posts

241 months

Wednesday 20th October 2010
quotequote all
rofl

SILICONE KID

Original Poster:

14,997 posts

262 months

Wednesday 20th October 2010
quotequote all
Wish some one had mentioned it,I asked about powder coating the plenum the other
dayrolleyes

Edited by SILICONE KID on Wednesday 20th October 21:44

spend

12,581 posts

282 months

Wednesday 20th October 2010
quotequote all
If you are lucky you may have witness compression marks which enable you to refit the TPS in pretty much the same place. Yet any re-alignment of the butterfly and slight misalignment of the TPS might affect the fine tuning of your map even though you reset the static points in the ECU... ie minor map tweaks may be required which could lead to major calamities depending on which 'operator' executes them hehe

Theres a bit more to stripping parts, sealing important bits, masking up then re-assembling in coating components than a simple take'n'bake garlic stick rofl

v8 racing

2,064 posts

282 months

Wednesday 20th October 2010
quotequote all
Quinny said:
Absolute classic quinny love it!!

v8 racing

2,064 posts

282 months

Wednesday 20th October 2010
quotequote all
SILICONE KID said:
Wish some one had mentioned it,I asked about powder coating the plenum the other
dayrolleyes

Edited by SILICONE KID on Wednesday 20th October 21:44
daz what you need to do is buy a pair of the biggest boxing gloves you can get, and when you want to work on your car, get the misses to glue them to your hands.....
hey we all love you really, what you are going to need to do now is make sure you have your megasquirt map saved (safely somewhere), when you put your plenum back together you WILL need to make sure that that the tps reading is exactly the same as what it was before you stripped it, its not difficult but just dont go adjusting things willy nilly or you will need a remap! HOMER

SILICONE KID

Original Poster:

14,997 posts

262 months

Wednesday 20th October 2010
quotequote all
Im taking the car back to Auto Tech.He is going to tweak the cruise a little as its a bit rich so he can sort this mess out.It will cost ..you live and learn.idea

Ribol

12,000 posts

289 months

Wednesday 20th October 2010
quotequote all
SILICONE KID said:
How do i remove the butterflyconfused
How about one of these?


Pink_Floyd

900 posts

252 months

Wednesday 20th October 2010
quotequote all
Ant. said:
now you have taken it all apart the chances of it going back in exactly the same way is minimal.
on my 1998 chim there is no adjustment on the throttle pot mounting so it will always go back in the same position.
Is this not true of all chims or are the earlier ones adjustable?

SILICONE KID

Original Poster:

14,997 posts

262 months

Friday 22nd October 2010
quotequote all
Mine as no adjustment so i can`t see why there should be any problems.

TVR Beaver

2,874 posts

211 months

Friday 22nd October 2010
quotequote all
Put an avo on it.. screw the screws in and see if you can move it about?.. you only have to breath on these things to change the value!.. I'd be very suprised if goes back in the same place!! rolleyes