outriggers
outriggers
Author
Discussion

gingar

Original Poster:

34 posts

199 months

Friday 22nd October 2010
quotequote all
looking for suggestions on how to paint the top of my outriggers without lifting the body?

saml666

222 posts

259 months

Friday 22nd October 2010
quotequote all
You could strip the interior and cut massive sections out of the fibreglass floor ...

...yeah, sorry, that's the smartarse forum comment you can do without. But I think a lift is the minimum requirement, body-off even better. Odds are you'll be painting over rust. Mine looked great underneath but a bodylift told a different story.

As a "Get you through a couple more MOTs" you could possibly send rust converter in under pressure from below, messy but might make you feel better. Sadly though, body lifting seems to become a necessity eventually.

Enjoy(?)
Sam

v8sag

827 posts

241 months

Friday 22nd October 2010
quotequote all
gingar said:
looking for suggestions on how to paint the top of my outriggers without lifting the body?


Sorry, not much chop

Pink_Floyd

900 posts

252 months

Friday 22nd October 2010
quotequote all
Mine looked pretty good from underneath, but from the top a different story.

Overhere

382 posts

254 months

Friday 22nd October 2010
quotequote all
There was an article in Sprint in a while back where a guy unbolted his body and lifted it only about 4 inches to clean and paint the top of the outriggers and some other frame sections. I'm thinking of doing that because it's not body off, so A LOT easier.

TVR Beaver

2,874 posts

211 months

Friday 22nd October 2010
quotequote all
Overhere said:
There was an article in Sprint in a while back where a guy unbolted his body and lifted it only about 4 inches to clean and paint the top of the outriggers and some other frame sections. I'm thinking of doing that because it's not body off, so A LOT easier.
Don't do it!!.. If you can, remove the body... I did a 4" lift 2 years ago.. and did manage to do the job as my outriggers were in good shape.. but all in it must have taken me 100 hours!!! (body lift / Clean off with various wire brushes / rub down / prep / pain POR15 3 coats / top coat / re-fit body etc)...
The problem was getting in to the top's still (there again I am a perfectionist so wanted ever mark out!!).. but even with long extensions in the drill and flexi-drives... it still took ages!
If you can get the body off and get propper access to it, it will save you a lot of time if you want to do the job right!!
But once don'e... It's piece of mind for sure wink

phillpot

17,524 posts

214 months

Friday 22nd October 2010
quotequote all
TVR Beaver said:
Don't do it!!.. If you can, remove the body... I did a 4" lift 2 years ago.. and did manage to do the job as my outriggers were in good shape.. but all in it must have taken me 100 hours!!!
100 hours ! must have been a lot of tea breaks hehe

lifted mine earlier this year, biggest hold up is waiting for coats of paint to dry.
Body off may be ideal but a lift can be done on your own and car back on road within a few days, full body off has just got to escalate into while its off I'll just . . . . . . .




-Pete-

2,914 posts

207 months

Friday 22nd October 2010
quotequote all
Someone remind me what the 4" limitation is, wiring loom? Is there any trick, elongate a bulkhead hole etc to allow 6" lift? I don't own one frown so maybe somebody can point me to some photo's which show what stops people lifting higher.

pk500

1,975 posts

243 months

Friday 22nd October 2010
quotequote all
Pink_Floyd said:
Mine looked pretty good from underneath, but from the top a different story.
i got some pictures like that

TJC46

2,199 posts

237 months

Friday 22nd October 2010
quotequote all
-Pete- said:
Someone remind me what the 4" limitation is, wiring loom? Is there any trick, elongate a bulkhead hole etc to allow 6" lift? I don't own one frown so maybe somebody can point me to some photo's which show what stops people lifting higher.
Did a full bodyoff so cant say for sure on a 4 inch or so lift, but any more than that and i would think you would be undoing all the brake/clutch pipes that run thru the inner wing. Im sure someone who knows for certain will be along soon.

-Pete-

2,914 posts

207 months

Friday 22nd October 2010
quotequote all
I'm factoring a body-off resto into any potential purchase, how long does it take? 10 hours off and 20 hours back on, excluding any work done inbetween?

BliarOut

72,863 posts

270 months

Friday 22nd October 2010
quotequote all
-Pete- said:
Someone remind me what the 4" limitation is, wiring loom? Is there any trick, elongate a bulkhead hole etc to allow 6" lift? I don't own one frown so maybe somebody can point me to some photo's which show what stops people lifting higher.
It's primarily the exhaust headers, 'twas me who wrote the Sprint article, feel free to ask away.

TVR Beaver

2,874 posts

211 months

Friday 22nd October 2010
quotequote all
What stops the body going any higher is the exhaust manifoulds... I actualy got about 5" at the front and 6-7" at the back....
The clutch and break pipes were no issue at this amount of lift at all...

But as said before.. if you want to get every last bit of rust off, it's still not the best...
Out of the 100 hours (est).. I'd say I spent
6 hours on the lift and getting it up / taking bits off etc
30 hours stripping and cleaning the metal tubes so they were perfect smile
then it took me 2 hours to give it a coat x 4.. so 10 hours with the pre-treatment and masking (does not include drying time)
then another 6 hours to drop it and put everything back on...
So total 52 hours (ok.. 100 was over the top but I was also doing the exhaust, seats out, new carpets, arb's out for painting, rad came out twice as I stripped it's tread on filling!! etc)
But it's a long time for sure... (or may be just felt like 100 hours!)
A body off would cost you time removing the manifoulds, disconnecting a few wires, brakes and clutch.. say another 3 hours tops... but does make life a lot easier!!.. O yes.. I did have a few cofee breaks
laugh


BliarOut

72,863 posts

270 months

Friday 22nd October 2010
quotequote all
On axle stands you're looking at a minimum of four hours to get the manifolds off IF you don't break any bolts smash You'll then need to disconnect all the fuel pipes, the wiring, the cooling and the brake lines biggrin

You then need some strong labour (or a crane Nige) and somewhere to store the body for the duration of the work.

The 4" raise is intended as a good solution if you have limited space.

I'd say working alone there is an additional day's work at each end between a raise and an off.

pk500

1,975 posts

243 months

Saturday 23rd October 2010
quotequote all
mine looked ok from underneath its so much easyer with the body off

Edited by pk500 on Saturday 23 October 13:31

pk500

1,975 posts

243 months

Saturday 23rd October 2010
quotequote all
i stripped it right down to the bare chassis and started from scratch painted up chassis after making and fitting new out riggers

Edited by pk500 on Saturday 23 October 13:36

roseytvr

1,790 posts

209 months

Saturday 23rd October 2010
quotequote all
Rob
Is the Sprint article the same as on the giff pages? Which month did it appear in?
Thanks

ray von

3,065 posts

283 months

Saturday 23rd October 2010
quotequote all
TVR Moneypit said:
Although some on here would say that my opinion isn't valid as my car is st and I'm no longer able to afford to throw £1500 p/m at it to get the engine sorted, I'll add my 2p anyway.

IMO, yes, the very best way is removing the shell and getting the full picture, but yes, this does take a hell of a long time, and yes, there is a mountain of other jobs that "you might as well do now" at the same time.

IIRC it is the wiring loom that prevent the shell from being lifted any more than 4" or so, but even raised this much it will give you a decent amount of space to work in. If time and cost are an issue, this is the route that I would reccomend. But, as has already been pointed out, my opinion is worth feck all anyway rolleyes
Nice one Frazer. If that's a thinly veiled dig at me, then you've misunderstood my post, although some seem to have been deleted from the thread anyway. My point was that no matter how many cars you see, you can still buy a one that can end up costing you a lot of money.
Take it from me I know that more than many after buying a car that was regarded as one of the best in the country, then spending a fking fortune putting it right.

Chris71

21,549 posts

273 months

Sunday 24th October 2010
quotequote all
Can I ask a numpty question here - if the problem is with the upper surface which you can't see, at what point do you (or the MOT man) know the outriggers require attention?

dogbucket

1,256 posts

232 months

Sunday 24th October 2010
quotequote all
To answer the OP.

If you have had a good root around and are sure as you can be that things are sound. Loop some 80 grit over the tubes to clean them up. Then I made a 'brush' which was a strip of metal bent into a hook with some self adhesive foam stuck on the inside to take the paint. Some artist brushes can get into the front plates quite well from the wheel arch. Follow all this up with some cans of Dinitrol into all areas using the optional tube/wand kit.