a quick sunday job has turned into a BIG load of jobs......
a quick sunday job has turned into a BIG load of jobs......
Author
Discussion

darkcat

Original Poster:

2,354 posts

201 months

Sunday 24th October 2010
quotequote all
So this morning i set about doing my engine mounts, however after getting the driver's side mount-to-chassis bolts out very easily, i turned to getting the mount bracket off the engine and discovered that there is no way to really get to the bolt heads with any known tool without taking the manifolds off.
so decided to resign myself to the car being off the read for a week or so.

got some big jobs to do:
- replace both engine mounts
- remove both manifolds, replace gaskets and knock out pre-cat's.
- check manifolds for cracks/leaks.
- apply high temperature paint to manifolds & cat/ y-piece.
- re-mount exhaust so it doesnt rattle.
- apply chassis sealant / POR15.
- remove induction system and find the annoying whistle.
- replace induction tubes with high-flow system from ACT.
- fit new rocker-cover gaskets.
- replace throttle position sensor.
- try to figure out what's squeeking when i apply the clutch
- and replace rear disks (did rear wheel bearings last weekend)

might do some work in the silencer while its off too.

Nothing expensive, just a LOT of work.


anyone who's bored and fancies helping out - your more than welcome!

Edited by darkcat on Monday 25th October 08:25

Chimjunkie

2,879 posts

242 months

Sunday 24th October 2010
quotequote all
Quinny said:
Would love to, but I'm doing my hair next weeksmile
Is that a back, sac and crack Quinny me old fker?

Edited by Chimjunkie on Sunday 24th October 19:08

chimaera1855

334 posts

199 months

Sunday 24th October 2010
quotequote all
hi (apply high temperature paint to manifolds & cat/ y-piece.)was wondering what do u use???and does it really work???i am trying to cool my lady as much as i can.tks

TJC46

2,199 posts

237 months

Sunday 24th October 2010
quotequote all
chimaera1855 said:
hi (apply high temperature paint to manifolds & cat/ y-piece.)was wondering what do u use???and does it really work???i am trying to cool my lady as much as i can.tks
I painted my manifolds and full exhaust system with a high temp aluminium paint from Stokes of sheffield. 2000 miles later and the only places that needed touching up were the manifolds.

ralphy12345

330 posts

196 months

Sunday 24th October 2010
quotequote all
TJC46 said:
chimaera1855 said:
hi (apply high temperature paint to manifolds & cat/ y-piece.)was wondering what do u use???and does it really work???i am trying to cool my lady as much as i can.tks
I painted my manifolds and full exhaust system with a high temp aluminium paint from Stokes of sheffield. 2000 miles later and the only places that needed touching up were the manifolds.
That looks the business!!! Any chance of a pic of the engine bay with them back in?

R


ralphy12345

330 posts

196 months

Sunday 24th October 2010
quotequote all
TJC46 said:
chimaera1855 said:
hi (apply high temperature paint to manifolds & cat/ y-piece.)was wondering what do u use???and does it really work???i am trying to cool my lady as much as i can.tks
I painted my manifolds and full exhaust system with a high temp aluminium paint from Stokes of sheffield. 2000 miles later and the only places that needed touching up were the manifolds.
That looks the business!!! Any chance of a pic of the engine bay with them back in?

R


TJC46

2,199 posts

237 months

Sunday 24th October 2010
quotequote all
ralphy12345 said:
TJC46 said:
chimaera1855 said:
hi (apply high temperature paint to manifolds & cat/ y-piece.)was wondering what do u use???and does it really work???i am trying to cool my lady as much as i can.tks
I painted my manifolds and full exhaust system with a high temp aluminium paint from Stokes of sheffield. 2000 miles later and the only places that needed touching up were the manifolds.
That looks the business!!! Any chance of a pic of the engine bay with them back in?

R

[/quote
Yes no problem.



Left click on either pic for a larger view.

Edited by TJC46 on Sunday 24th October 22:13

ralphy12345

330 posts

196 months

Sunday 24th October 2010
quotequote all
TJC46 said:

Yes no problem.

Wow! I can see I've got some way to go yet! biggrin

R

Iain328

15,120 posts

237 months

Sunday 24th October 2010
quotequote all
chimaera1855 said:
hi (apply high temperature paint to manifolds & cat/ y-piece.)was wondering what do u use???and does it really work???i am trying to cool my lady as much as i can.tks
If you really want to drop the engine bay temperatures then Zircotec or some other kind of ceramic coating is the way to go. http://www.zircotec.com/

Not cheap but its the best way.

haircutmike

22,511 posts

235 months

Monday 25th October 2010
quotequote all
ralphy12345 said:
TJC46 said:

Yes no problem.

Wow! I can see I've got some way to go yet! biggrin

R
Is this a test?

Do I win the prize for noticing you have invisible HT leads?

Nice bay!

darkcat

Original Poster:

2,354 posts

201 months

Monday 25th October 2010
quotequote all
Chimaera1855 - Actually i was going to do it purely for aesthetics, not for keeping temperatures down, tho any effect would be nice.

Right then, off to buy some gaskets....

oh - question - is there supposed to be any sort of gasket between the manifolds and the y-piece? when i took the clamps off there was just a load of exhaust sealant in there. they didnt blow at all but thought i should ask.

haircutmike

22,511 posts

235 months

Monday 25th October 2010
quotequote all
Mine has no gaskets and no sealent either and doesn't leak.

I would scape off all the sealent prior to assembly.

This weekends work included;

New P/S steering rack fitted.
New Superflex ARB mounts.
Rebuilt diff fitted.
New monotube dampers fitted.

All went reasonably to plan, (thanks Alex), apart from the rear damper spacers being a couple of mm to wide mad and Kielly & Clinton didn't send back my locking nuts for the track rod ends when they returned my old "crap" rack!madmad

Oh well, another couple of days won't hurt I guessrolleyes

darkcat

Original Poster:

2,354 posts

201 months

Monday 25th October 2010
quotequote all
stumped at the first hurdle......

eventually managed to track down a suitable spanner to get at the top manifold bolts, they are now all out.
but the bottom ones??? jesus! im really struggling to get at them from the top or underneath...
am i missing something??

STEV8E

635 posts

240 months

Monday 25th October 2010
quotequote all
darkcat said:
am i missing something??
Dont think so, I found it a real pain. Good feeling when its all back together again though!

edward1

839 posts

297 months

Monday 25th October 2010
quotequote all
I remember trying to tighten my manifold bolts when i thought it was blowing, I found that from the bottom with an open ended spanner I could only turn about 1/4 turn a time. I was glad I wasn't trying to remove them, and have always paid someone to do that job since!

darkcat

Original Poster:

2,354 posts

201 months

Monday 25th October 2010
quotequote all
edward1 said:
I remember trying to tighten my manifold bolts when i thought it was blowing, I found that from the bottom with an open ended spanner I could only turn about 1/4 turn a time. I was glad I wasn't trying to remove them, and have always paid someone to do that job since!
yes thats the problem im having, ive given up now, getting too cold. got 2 of them out now, i can see this being one of those "i wish i hadnt started" things....!

darkcat

Original Poster:

2,354 posts

201 months

Monday 1st November 2010
quotequote all
well im winning!! FINALLY got the right manifold off, and have only one nukkle missing.

how do i get the lambda sensor out?


SILICONE KID

14,997 posts

262 months

Monday 1st November 2010
quotequote all
Cut a slit in a socket then you can push the cable through,if it trys to open up use a Jubilee Clip..

edward1

839 posts

297 months

Tuesday 2nd November 2010
quotequote all
I found to my expense (after buying the socket) that the lambda sensors are not the same size socket as what most vehicles must be. I bought a cheap box spanner and cut a slot in it. I wasn't trying to extert too much force though as all I wanted to to tighten one up that had come loose. For a couple of quid from a second hand tool shop it woked well.