waxoil or not powder coated chassis
waxoil or not powder coated chassis
Author
Discussion

floyd12345

Original Poster:

125 posts

205 months

Saturday 30th October 2010
quotequote all
Just had my chassis zinc primed and powder coated and i have started to rebuild it while its all accessible should i cover in wax oil or leave it all nice and clean?

gadgit

971 posts

298 months

Saturday 30th October 2010
quotequote all
get it waxoiled ASAP. just make sure you have a proper job, and not some half baked effort.

Or coat it every year in old engine oil......which would you rather do??

Gadgit.

anonymous-user

85 months

Saturday 30th October 2010
quotequote all
If you do wax-oil before you rebuild it will get covered in much and cr*P will stick to it as you re assemble.

blitzracing

6,422 posts

251 months

Saturday 30th October 2010
quotequote all
Personally I would not use old engine oil, as apart from the horrible smell its full of acids from the combustion process. If I was in your situation Id put it on discreetly with a paint brush in all the hidden areas and nuts and bolts you wont be able to get at at a later date, but leave the rest as is, it would seem a pity to cover what should be a much better coating than the factory did, and after all if it does start to rust, you can still put Waxoyle on a a later date. It is going to look exceptionly horrible on a white chassis as road dirt sticks to it. The black Waxoyle on a black chassis looks OK.

Defcon5

6,479 posts

222 months

Saturday 30th October 2010
quotequote all
What is the benefit of waxoyling a powdercoated part? There isnt any bare metal for it to cover

ralphy12345

330 posts

196 months

Saturday 30th October 2010
quotequote all
Wouldn't Waxoyl be a good idea for inside the tubular sections?

R

VictorMeldrew

8,293 posts

308 months

Saturday 30th October 2010
quotequote all
Defcon5 said:
What is the benefit of waxoyling a powdercoated part? There isn't any bare metal for it to cover
If you use the waxoyl undercoat it forms a thick self-healing coat over the powdercoat that can help prevent chipping.

V8NRG

854 posts

274 months

Sunday 31st October 2010
quotequote all
I'm just starting a body off chassis job and will not be using waxoil !

I'm going to use stone chip paint on the outriggers and nothing on the rest of the chassis apart form the powder coat.

Ironballs

363 posts

206 months

Sunday 31st October 2010
quotequote all
My 05 Tam has waxoyl covering all the exposed parts underneath, doesn't look as nice as clean chassis tubes but it does protect them from stones and crap

quattrophenia

1,103 posts

229 months

Sunday 31st October 2010
quotequote all
My chassis looks great and has been treated in the past, and so it should for a low mileage cared for dry use car. However I do feel a bit guilty just leaving it over winter. Do most people strip off all the old white powder coat and start again. Having looked at mine it would appear the best way forward by far would be to simply clean the good powdercoat of all dirt and old waxoil and than apply a new sealer product. Any views guys.

TJC46

2,199 posts

237 months

Sunday 31st October 2010
quotequote all
V8NRG said:
I'm just starting a body off chassis job and will not be using waxoil !

I'm going to use stone chip paint on the outriggers and nothing on the rest of the chassis apart form the powder coat.
I.M.O. have to agree. After all the work of doing a bodyoff and chassis refurb, theres no need to cover in waxoil. Top of the outriggers and triangle plates where the body bolts on yes, but the rest of the chassis is best left all shiney. Easier to inspect for stone chips etc and easy to touch up. Im sure there will be plenty of opinions for and against on this topic!

carsy

3,019 posts

196 months

Sunday 31st October 2010
quotequote all
My chassis is just about to have its new outriggers on and then off for new powdercoating. I have to admitt the old waxoil has kept the chassis in decent nick over the last 18yrs, but after the nightmare ive had cleaning it off it will certainly not be going back on. When completed it will only be used on dry summer days so will keep it just the powdercoat bar the outriggers where i will put a stone chip paint or similar.

rb5230

11,657 posts

203 months

Sunday 31st October 2010
quotequote all
slap a few coats of hammerite on it and then waxoyl it to death.

probably crap idea.

Adrian@

4,664 posts

313 months

Sunday 31st October 2010
quotequote all
I have professionally re built TVR's for the last 30 years (some 70 plus cars)and stopped using powder coating in 1991, using Hot zinc spraying/etch/primer/wet painting then a coat of clear waxoyl ...that said, I use powder for all the parts that can come off and touch up the hanging point with 2 part epoxy paint.
IMHO you NEED to go over the new powder coated work and hand paint any dry parts (in tight corners etc) blank off any welded bosses that are not going to be used and use a sealer on the ones that are so that the chassis is airtight ...DO NOT fill the tubes with waxoyl as IF the chassis need to be repaired at any time in the future it is impossible to weld, as all the fumes will not allow the weld to seal (in process of welding the fumes ignite).
Adrian@
PS OP, looks good.

Edited by Adrian@ on Sunday 31st October 14:48

carsy

3,019 posts

196 months

Sunday 31st October 2010
quotequote all
Quinny, Youve set me off again now. For weeks ive been researching between powdercoating and 2 pack paint and just the other day decided on powdercoat. Ill have to do more thinking. Whats your reasoning for not powdercoating. confused

Barkychoc

7,848 posts

235 months

Sunday 31st October 2010
quotequote all
I honestly think theres too much worry about what to coat it with - most of these cars are now in the hands of enthusiasts who keep a close eye on things - and they are more than likely now doing lower annual mileages so any issues are picked up much earlier.

I don't think its any secret that TVR's powder coating process was crap - but if done properly its still a good process in my opinion - there's no right and wrong answer what to coat it with IMHO - each to their own.

I think the problems generally stem from water getting inside the outriggers from a rot hole generally just above the front body mounting plate where you can't see it - rot then sets in from the inside and no amount of waxoyl on the outside is going to help.

There's a few specialists about now who replace outriggers at very reasonable cost - I'd just view it as a major bit of maintenance in the same way you would a replacement cam or something - TVR's were always about low cost performance relatively speaking to there had to be some compromises. At least they are made from simple bits of readily available steel and not some far eastern unobtanium.

I think we also forget the age of a lot of these cars now - anything of similar age will be looking tired underneath TVR or otherwise.