Jacking
Author
Discussion

BenRelle

Original Poster:

1,796 posts

205 months

Saturday 30th October 2010
quotequote all
When I was buying my Chim, I jacked from the outriggers either side in line with where the diagonal member goes up to the backbone. Now I want to jack the car up and get it onto axle stands at all 4 corners. Had a peep under the read or the car and can't immediately see where I could jack the car up and have the whole of the rear lift in one go. Haven't looked at the front, but suspect there must be a crossmember somewhere...

Anyone got hints on how to get it up (as it were)?

dog man

552 posts

233 months

Saturday 30th October 2010
quotequote all
Just get right under to the inner box section, use some wood to prevent denting/damage to the chassis. Jack one side and pop your axle stand under then do t'other side (place them well obviously). I have to say I always find it nerve racking doing this so just take it slowly, it should ultimately be fine if done safely!

V8NRG

854 posts

274 months

Sunday 31st October 2010
quotequote all
dog man said:
Just get right under to the inner box section, use some wood to prevent denting/damage to the chassis. Jack one side and pop your axle stand under then do t'other side (place them well obviously). I have to say I always find it nerve racking doing this so just take it slowly, it should ultimately be fine if done safely!
This is what i do.

Front jacked on the front crossmember. Rear jacked on the rear outriger parts either side one at a time. Quite nerve racking but it works!

quattrophenia

1,103 posts

229 months

Sunday 31st October 2010
quotequote all
Are Chims too low to drive onto the sort of standard ramps that are available at Halfrauds? They are about £40 for a pair and would lift one end of your car say 1-2 foot up. This access would seem OK so long as you can get the car up/down the ramp with out ripping off the bumper and dont need to take the wheels off.

BenRelle

Original Poster:

1,796 posts

205 months

Sunday 31st October 2010
quotequote all
Suspect it would work, and i do have a set of ramps, but i want to do this inside the garage (it's chilly/wet outside), and some of my experiences getting cars onto them have been 'interesting' to say the least. You can get hydraulic ramps that you drive onto and then jack up - they're quite smart, and would work well. Don't have any though. One of my first jobs is to change the headlamp bulbs (nearside doesn't have a dipped beam ATM), wheel does need to come off...

pbaker43

268 posts

199 months

Sunday 31st October 2010
quotequote all
As quinny said jack the rear using the diff, for the front end I find driving or putting a house bricks under the wheels gives just enough room to slide a jack under a cross member.

4Lmike

1,910 posts

201 months

Sunday 31st October 2010
quotequote all
quattrophenia said:
Are Chims too low to drive onto the sort of standard ramps that are available at Halfrauds?
I would say so, although I've not actually tried it myself.

storm grey

271 posts

213 months

Sunday 31st October 2010
quotequote all
mine is up on a set of ramps at the mo no problem just put a piece of timber first to give you the height to get on the ramps

BenRelle

Original Poster:

1,796 posts

205 months

Monday 1st November 2010
quotequote all
I got it up in the end (fnarr). Luckily I have 2 trolley jacks, so i jacked one side up on the outrigger at the front(where the triangulation is, as above), got it high enough to get the other jack under the front crossmember and up she went. Because the front was now up, I could get the jack under the back of the car on the chassis near where the wishbone is mounted, and up she went that side too. I stupidly forgot to loosen the wheelnuts before this though, and my air powered impact wrench won't touch them. Someone's obviously used a really high power jobbie to put them on. I don't know what the torque setting is supposed to be for these wheels, but I suspect that these are tightened way over. At least I now know how to do it....

Looking in detail at the outriggers and really digging at them means that shedloads of rust/powdercoat rains down, but no actual penetration as yet. They don't look very nice though, so I'll go back through the waxoyl/por15 etc. type threads...


Cheers for the replies chaps.


spend

12,581 posts

282 months

Monday 1st November 2010
quotequote all
Slice up a few 8x2" lengths to drive up, jacks go straight under the main chassis rails no problem then.