Audi Q5 Wing Mirror Question
Discussion
Morning all.
The wing mirror on my wife's Q5 has experienced a rather annoying incident. The thin, clear plastic indicator lens has cracked and a 2 inch section has fallen out - it's the section that looks orange in the image below.
Does anyone know whether or not this is an individual part? Is it possible to simply dismantle the housing, remove the broken part and install the new one?
Any help greatly appreciated - thanks.

The wing mirror on my wife's Q5 has experienced a rather annoying incident. The thin, clear plastic indicator lens has cracked and a 2 inch section has fallen out - it's the section that looks orange in the image below.
Does anyone know whether or not this is an individual part? Is it possible to simply dismantle the housing, remove the broken part and install the new one?
Any help greatly appreciated - thanks.

You need skinny fingers and patience.
Push the bottom of the glass as far in as you go (i.e. make the glass point down). Then get your fingers in behind the glass as close to the middle as possible and pull it away from the centre. Try not to 'bend' the glass as this will make it snap, the further you can get your fingers behind the glass the easier it is. The spade connectors on the heating elements are a bit fiddly too.
Push the bottom of the glass as far in as you go (i.e. make the glass point down). Then get your fingers in behind the glass as close to the middle as possible and pull it away from the centre. Try not to 'bend' the glass as this will make it snap, the further you can get your fingers behind the glass the easier it is. The spade connectors on the heating elements are a bit fiddly too.
Quick update should this happen to anyone in the future.
Firstly, check ebay for parts. I found the genuine part in Germany and paid £17 delivered, which is obviously way cheaper the the c.£50 I was quoted from Audi.
Regarding the install, mirror removal is a mentioned above; point the mirror as far down as possible and get your fingers behind it from the top. Pull from the centre without trying to 'bend' the glass. This is the least comfortable step in the process.
Remove the heating element connectors and put the glass to one side, somewhere safe so you don't step on it. There's alot going on in the wing mirror but don't be tempted to remove the torx screws you see before you as it is not required. The top piece of the wing mirror housing (the body coloured bit) pops off and the indicator lens is bolted to it. This is the second least comfortable step of the process as you have to simply work the top piece off by pulling where you can feel the resistance of clips. Remember the indicator lens clip needs to be unclipped, once the housing has come free.
From there it is easy; remove the indicator lens from the housing and fit the new one. Follow the steps above in reverse order, remembering to reconnect the indicator lens and heating elements as you go... and probably worth checking your indicator lens works before re-fitting the mirror.
Good luck if you try it, although hopefully you won't need to.
Firstly, check ebay for parts. I found the genuine part in Germany and paid £17 delivered, which is obviously way cheaper the the c.£50 I was quoted from Audi.
Regarding the install, mirror removal is a mentioned above; point the mirror as far down as possible and get your fingers behind it from the top. Pull from the centre without trying to 'bend' the glass. This is the least comfortable step in the process.
Remove the heating element connectors and put the glass to one side, somewhere safe so you don't step on it. There's alot going on in the wing mirror but don't be tempted to remove the torx screws you see before you as it is not required. The top piece of the wing mirror housing (the body coloured bit) pops off and the indicator lens is bolted to it. This is the second least comfortable step of the process as you have to simply work the top piece off by pulling where you can feel the resistance of clips. Remember the indicator lens clip needs to be unclipped, once the housing has come free.
From there it is easy; remove the indicator lens from the housing and fit the new one. Follow the steps above in reverse order, remembering to reconnect the indicator lens and heating elements as you go... and probably worth checking your indicator lens works before re-fitting the mirror.
Good luck if you try it, although hopefully you won't need to.
Edited by mab13 on Tuesday 12th November 09:46
Gassing Station | Audi, Seat, Skoda & VW | Top of Page | What's New | My Stuff




