08 facelift b8 audi a4- rear bulb holder corroded - outofwar
Discussion
Hi
My audi 08 (facelift - 2009+ model )rear bulb holder has corroded - the bulb holder that holds the reverse light which is fitted in the boot lid - not where boot well is with the side indicators/main light
Surely this is a design fault by audi? the car is out of warranty - granted but never had this
issue on any car I've ever owned.
Also appears water of got in there? how???
Has there been any factory recalls for this issue?
Absolute joke to be honest.
Thoughts and cheapest place to get the part/ number etc?
Thanks everyone
My audi 08 (facelift - 2009+ model )rear bulb holder has corroded - the bulb holder that holds the reverse light which is fitted in the boot lid - not where boot well is with the side indicators/main light
Surely this is a design fault by audi? the car is out of warranty - granted but never had this
issue on any car I've ever owned.
Also appears water of got in there? how???
Has there been any factory recalls for this issue?
Absolute joke to be honest.
Thoughts and cheapest place to get the part/ number etc?
Thanks everyone
Edited by mikiesb on Sunday 2nd March 16:57
Edited by mikiesb on Sunday 2nd March 17:06
contacted audi uk - useless.
Told them i've never had a car with this issue.
Went to audi dealership today, bought a new bulbhoder - £18, fitted a new reverse light bulb and all error codes on dash have gone..
But..on further inspection the rubber seals seem to be the problem but i haven't stripped out the boot lid lights yet. Rubber seals £6 each per side so doing them both as a precaution.
There is condensation in the lights, so looks like i will have to remove them, dry them out (airing cupboard or hairdryer?), refit the rubber seals.
How easy is it to the rubber seals? I presume even for a rubbish DIYer like me even I should be able to do it?
Told them i've never had a car with this issue.
Went to audi dealership today, bought a new bulbhoder - £18, fitted a new reverse light bulb and all error codes on dash have gone..
But..on further inspection the rubber seals seem to be the problem but i haven't stripped out the boot lid lights yet. Rubber seals £6 each per side so doing them both as a precaution.
There is condensation in the lights, so looks like i will have to remove them, dry them out (airing cupboard or hairdryer?), refit the rubber seals.
How easy is it to the rubber seals? I presume even for a rubbish DIYer like me even I should be able to do it?
As in the rubber seal that sandwiches between the bulb holder and the light housing?
If so they just pull out and push back in. The new ones will be a tight fit, when I did mine the old ones had gone sort of soft and the seal was a bit pants. I used a hair dryer to get rid of the condensation and when reassembling you can tell the seal is better because the bulb holder is much tougher to click back into place with the new rubbers in.
If so they just pull out and push back in. The new ones will be a tight fit, when I did mine the old ones had gone sort of soft and the seal was a bit pants. I used a hair dryer to get rid of the condensation and when reassembling you can tell the seal is better because the bulb holder is much tougher to click back into place with the new rubbers in.
You get v. similar problems on the A6.
The only solution that works on is to drill a series of holes along the bottom edge of the light cluster to improve ventilation. The A8 may have the same solution?
http://www.vwaudiforum.co.uk/forum/showthread.php?...
I've done the drill-holes fix in this thread and it worked.
The only solution that works on is to drill a series of holes along the bottom edge of the light cluster to improve ventilation. The A8 may have the same solution?
http://www.vwaudiforum.co.uk/forum/showthread.php?...
I've done the drill-holes fix in this thread and it worked.
Hi
Thanks for the replies.
Car has never been in an accident (touchwood), bought it from a friend who had it as a company car - so bought it from his company - FASH unti I bought it a year ago ish.
The bulb holder in the boot lid was corroded.
I have left open the carpet to the bulb holder and the condensation/water has now gone (dried out naturally)
Audi dealers said the rubber seals had more than likely gone round the cluster that holds the reverse light bulb etc.
But to confirm this it would cost £80/100 to confirm what I know already... excuse my french ... f.f.sake.
Then the dealers (who were not the dealers who carried out the service during it's life) say car has not been serviced recently at an audi dealers so then audi uk will definitely not give me any "goodwill".
So..
£6 x 2 = £12 new rubber seals
£20 = new bulb holder
£3 = new reverse bulb
£36 for parts vs £100 "sucking eggs exercise by local audi dealers" to then send onto audi uk to then
be kicked in the nuts ????
No brainer.
No common sense.
Even Honda UK were fantastic to me when I had consistent type r issues that were out of warranty years ago and the "goodwill" was in the £1000's. - but that's another story.
Anyway shtu please please! can you tell me the page number of the drill holes fix for audi a6.
Many many thanks everyone !
Thanks for the replies.
Car has never been in an accident (touchwood), bought it from a friend who had it as a company car - so bought it from his company - FASH unti I bought it a year ago ish.
The bulb holder in the boot lid was corroded.
I have left open the carpet to the bulb holder and the condensation/water has now gone (dried out naturally)
Audi dealers said the rubber seals had more than likely gone round the cluster that holds the reverse light bulb etc.
But to confirm this it would cost £80/100 to confirm what I know already... excuse my french ... f.f.sake.
Then the dealers (who were not the dealers who carried out the service during it's life) say car has not been serviced recently at an audi dealers so then audi uk will definitely not give me any "goodwill".
So..
£6 x 2 = £12 new rubber seals
£20 = new bulb holder
£3 = new reverse bulb
£36 for parts vs £100 "sucking eggs exercise by local audi dealers" to then send onto audi uk to then
be kicked in the nuts ????
No brainer.
No common sense.
Even Honda UK were fantastic to me when I had consistent type r issues that were out of warranty years ago and the "goodwill" was in the £1000's. - but that's another story.
Anyway shtu please please! can you tell me the page number of the drill holes fix for audi a6.
Many many thanks everyone !
hi shtu
found this link in the thread your on about
http://s140.photobucket.com/user/jaycam0802/media/...
so i presume i take the cluster out of my bootlid, dry out, then drill 10 holes along the bottom of the cluster from left to right with the drill bit facing upwards? so the holes create mini holes at the bottom of the cluster?
Thanks
found this link in the thread your on about
http://s140.photobucket.com/user/jaycam0802/media/...
so i presume i take the cluster out of my bootlid, dry out, then drill 10 holes along the bottom of the cluster from left to right with the drill bit facing upwards? so the holes create mini holes at the bottom of the cluster?
Thanks
Edited by mikiesb on Thursday 6th March 22:25
Edited by mikiesb on Thursday 6th March 22:25
just to add, I had the same problem late last year with my 2008 A4, dash warnings of the reverse light being out and the whole thing being temperamental. The bulb-holders were corroded, I got my indy to sort it while it was in for other work, so they only charged £15 for the new holder, not had a problem since.
I understand it may be a poor design, but a £15 bill every 5 years isn't too bad so just paid it and moved on really.
I understand it may be a poor design, but a £15 bill every 5 years isn't too bad so just paid it and moved on really.
mikiesb said:
http://s140.photobucket.com/user/jaycam0802/media/...
so i presume i take the cluster out of my bootlid, dry out, then drill 10 holes along the bottom of the cluster from left to right with the drill bit facing upwards? so the holes create mini holes at the bottom of the cluster?
That's the idea.so i presume i take the cluster out of my bootlid, dry out, then drill 10 holes along the bottom of the cluster from left to right with the drill bit facing upwards? so the holes create mini holes at the bottom of the cluster?
You don't have to have the exact same number of holes as the diagram, but I marked out some thing similar with pencil, "pilot" drilled with a 1mm bit, then followed that with a 3mm bit.
Use brand-new drill bits, and go gently - on the A6, it's easy to drill past the outer housing and damange the inner if you're not careful, so you stop as soon as you feel the drill push through. I've no idea of the layout of the A8 lights, so it's definitely something to look at and decide if it's suitable.
You can *just* see the holes on the A6 lights if you know where to look, but it's better than the light being full of condensation.
Also, tke a look at the connector and multi-plug that connects the light to the car - on mine, the earth connector showed signs of overheating and pitting, which caused several bulb "failures" on the cluster.
(Edit - Page 18 onwards.)
Edited by shtu on Friday 14th March 11:39
Folks, exact same issue for me with corroded inner bulb holder on both sides though left is worst. Does anyone have the Audi part numbers for the bulb holders and the rubber seals please. Number printed on the Hella bulb holder did not seem to bring up anything when I Googled it. Cheers.
shtu -
the connector cable that powers up bulb holder has slightly corroded contacts - i have tried a cotton bud and a small bit of wd40 - this cleared the problem for a while..but thankfully no more irratating beebs !!!
my new bulb holder contacts are fine (there's 4 small prongs)
Should i try cleaning the contacts with a brillo pad or wire wool or something "abrasive" - sandpaper?
les...
I am going to audi parts dept tomorrow - i will get both part numbers for you - again another 1 of my pet "hates" no part number unless you buy parts... another story.
my diy is useless on cars but even i have managed to remove the rear cluster - remove bulb holder then 1 x 10mm bolt and viola out it pops.
tbh - i've looked at the rubber seals and they look fine..
there doesn't seem to be any special way of fitting these because i've removed and refitted them - and they look flush when re-seated.
Believe me if I strip these down and replace the seals and it doesn't work out I will be driving to audi hq in milton keynes and going mental BIGTIME.
I will say it again - Audi customer care/uk could learn alot from Honda in regards to common sense/respect of their customers...
the connector cable that powers up bulb holder has slightly corroded contacts - i have tried a cotton bud and a small bit of wd40 - this cleared the problem for a while..but thankfully no more irratating beebs !!!
my new bulb holder contacts are fine (there's 4 small prongs)
Should i try cleaning the contacts with a brillo pad or wire wool or something "abrasive" - sandpaper?
les...
I am going to audi parts dept tomorrow - i will get both part numbers for you - again another 1 of my pet "hates" no part number unless you buy parts... another story.
my diy is useless on cars but even i have managed to remove the rear cluster - remove bulb holder then 1 x 10mm bolt and viola out it pops.
tbh - i've looked at the rubber seals and they look fine..
there doesn't seem to be any special way of fitting these because i've removed and refitted them - and they look flush when re-seated.
Believe me if I strip these down and replace the seals and it doesn't work out I will be driving to audi hq in milton keynes and going mental BIGTIME.
I will say it again - Audi customer care/uk could learn alot from Honda in regards to common sense/respect of their customers...
ok les here's the part numbers for you.
bulb holder - PA8K5 945 258 B = right side bulb holder £17.56 total
PA8K5 945 191 A - gasket (rubber seal)
PA8K5 945 191 B - gasket (rubber seal)
Must say stripping away the existing rubber and refitting this rubber it seemed to be a more "tight" feeling
when bolting back in...
bulb holder - PA8K5 945 258 B = right side bulb holder £17.56 total
PA8K5 945 191 A - gasket (rubber seal)
PA8K5 945 191 B - gasket (rubber seal)
Must say stripping away the existing rubber and refitting this rubber it seemed to be a more "tight" feeling
when bolting back in...
mikiesb said:
Should i try cleaning the contacts with a brillo pad or wire wool or something "abrasive" - sandpaper?
What I did was remove the pin from the connector, and use very fine wet and dry paper to clean it up, then tightened it up a bit.iirc the purple plastic "clip" just slides out, and then carefully push the pin's locking lugs back with a paperclip bent to suit. Fiddly, but not impossible.
Well I finally pressure tested these on sat - took my car to the jetwash (removed bulb holders before jetwashing wrapped plastic bags round bulb holders then re-seated) and now no leaks - so in a nutshell worth £12 for the replacement seals.
10mm spanner to remove, sharp knife to clean the seals down, replace seals, then refit.
If I can do it - anyone can !
10mm spanner to remove, sharp knife to clean the seals down, replace seals, then refit.
If I can do it - anyone can !
Gassing Station | Audi, Seat, Skoda & VW | Top of Page | What's New | My Stuff



