Cam Belt Failure - Audi A3 2.0TDI
Cam Belt Failure - Audi A3 2.0TDI
Author
Discussion

simondr

Original Poster:

5 posts

149 months

Thursday 12th June 2014
quotequote all
I wonder if anyone can offer any advice? I had my cam belt changed at a local Halfords Autocentre back in December and was happily driving home on Sunday and it failed. Called the AA etc etc and had car dropped back at the garage.

Basically they are saying it's parts failure, and I'm sure the parts supplier will say workmanship but I am getting nowhere.

No replacement car and I'm having to constantly chase Halfords to which I now feel I'm being ignored. The parts have apparently been sent away to be x-rayed? and they have also sent away the water pump which wasn't changed when they did replaced cam belt?

Are they going to try and use the water pump as a get out? The initial prognosis from the Autocentre manager was a tensioning bolt snapping?

Thanks in advance guys/girls

anonymous-user

85 months

Thursday 12th June 2014
quotequote all
i would have paid for an independent inspection before sending parts to them.

waterpumps are usually an add on..

simondr

Original Poster:

5 posts

149 months

Thursday 12th June 2014
quotequote all
Thanks for the feedback, the impression I got from the manager was it was definitely a parts failure. They apparently have a "Quality Guarantee" which covers 12,000 miles or 12 months whichever the sooner and I'm well inside those parameters but i've got a very uneasy feeling!

anonymous-user

85 months

Thursday 12th June 2014
quotequote all
they will argue mechanical failure over belt dailure, i would guess considering the price. For a better answer, post this in law section.

But depending how rich you are i would take free/paid legal advice on the matter as it may become messy.

simondr

Original Poster:

5 posts

149 months

Thursday 12th June 2014
quotequote all
Thanks again, I will post in law section as suggested.

mattyc69

337 posts

183 months

Thursday 12th June 2014
quotequote all
I hope they don't but they may go for the water pump seizing up causing the belt to snap! See it happen to a 1.9 PD engine before.

simondr

Original Poster:

5 posts

149 months

Thursday 12th June 2014
quotequote all
That's the only thing I'm concerned about Matty, I did ask them at the time if they would be changing that too but they said only if it needed it? Still not sure about his original comment of a tension bolt snapping though and how this is connected to water pump failure. Then again I'm no expert!


AGK

1,605 posts

186 months

Friday 13th June 2014
quotequote all
I've got a feeling the tensioner bolts are one use and stretch bolts...

cuprabob

19,913 posts

245 months

Friday 13th June 2014
quotequote all
I would have thought if it was the tensioner bolt, the belt would have went slack, sprockets would have jumped knocking the timing out and possibly a few valves into the piston.

cuprabob

19,913 posts

245 months

Friday 13th June 2014
quotequote all
I would have thought if it was the tensioner bolt, the belt would have went slack, sprockets would have jumped knocking the timing out and possibly a few valves into the piston.

toerag

758 posts

163 months

Friday 13th June 2014
quotequote all
simondr said:
I had my cam belt changed at a local Halfords Autocentre

Spangles

1,441 posts

216 months

Sunday 15th June 2014
quotequote all
It is no doubt the tensioner stud that has snapped. It is a common failure with these engines, usually not long after a cambelt change. The bolt on the stud should be tightened to 25Nm plus 45 degrees, fine for a brand new stud, possibly too much the second time. VW didn't used to include a new stud with their kit, apparently they now do. Gates have supplied one for ages.

RammyMP

7,750 posts

184 months

Sunday 15th June 2014
quotequote all
toerag said:
simondr said:
I had my cam belt changed at a local Halfords Autocentre
+1 my local one couldn't fit my windscreen wipers!

rsv696

474 posts

174 months

Sunday 15th June 2014
quotequote all

Tame Technician

2,467 posts

235 months

Sunday 15th June 2014
quotequote all



http://www.audi.co.uk/owners-area/servicing-mainte...

Audi dealer fixed price cam belts for cars over 3 years old and 2.0L or less, inc 2.0TDI

Free MOT for life if we do your belt

2 Years parts warranty.

£449

Tame Technician

2,467 posts

235 months

Sunday 15th June 2014
quotequote all
That tensioner stud (not bolt) can cause the tensioner to go slack if it fails.

Damage varies from none at all, new parts on time up and all is well, to needing a rebuilt cyclinderhead.

Hope they find a part failure and you get it all fixed for free.

If the stud has failed and they didnt replace it, and they suggest its not their doing because they didnt replace that part, you need to imply they overtightened the nut and caused the stud to fail.


simondr

Original Poster:

5 posts

149 months

Sunday 15th June 2014
quotequote all
Thanks for all your comments guys....helpful or otherwise!

Have now heard back and I'm apparently getting new engine at no cost to me! Guessing it's a re-manufactured one but it'll be one I won't be paying for :-)

thanks again!

anonymous-user

85 months

Sunday 15th June 2014
quotequote all
simondr said:
Thanks for all your comments guys....helpful or otherwise!

Have now heard back and I'm apparently getting new engine at no cost to me! Guessing it's a re-manufactured one but it'll be one I won't be paying for :-)

thanks again!
good result

Sheepshanks

41,366 posts

150 months

Sunday 15th June 2014
quotequote all
simondr said:
Thanks for all your comments guys....helpful or otherwise!

Have now heard back and I'm apparently getting new engine at no cost to me! Guessing it's a re-manufactured one but it'll be one I won't be paying for :-)

thanks again!
They are fairly well known for paying out when they mess up. I wouldn't dream of having work done there, but it is an advantage of a large corporate that it's not a big deal to them to put it right.

mattyc69

337 posts

183 months

Monday 16th June 2014
quotequote all
Sorry never read the post properly missed the bit about the stud, but a very good result indeed! Please for you.