vw 1.8 turbo engine aum
Author
Discussion

sparkieboy29

Original Poster:

5 posts

198 months

Sunday 23rd May 2010
quotequote all
Hi all im new to the site so a big hello :-),ive a problem with my 1.8 turbo golf, my dad has been using it and has blown the engine up through lack of servicing !... the engine code is AUM can i replace the engine with a diffrent coded engine as im having problems sourcing AUM engine,and the cost of a rebuild in not worth doing on the car due to its value ?
cheers
All help would be greatly recieved
cheers
Andy

aka_kerrly

12,506 posts

241 months

Monday 24th May 2010
quotequote all
Yo,
Have a look at this guide and you can figure out which other 20vt engines are compatible. When he killed the engine, what exactly happened, are you after a long block or do you need the turbo set up to as this will have massive impact on the price.

dave

sparkieboy29

Original Poster:

5 posts

198 months

Tuesday 25th May 2010
quotequote all
I've been told unless the car is serviced properly the oil feed th the cams fail ie lack of oil at the top of the engineand seized up I'm think turbo etc is all good as there was oil in the car just not at the top of the engine !..

Matt_N

9,045 posts

233 months

Tuesday 25th May 2010
quotequote all
Oil pumps can sludge up on these engines if regular oil changes aren't done, so maybe this was the cause.

Sign up to www.edition38.com/forums there are normally a few 1.8T engines for sale.

AUM is drive by wire throttle so you'll be needing an AUM / AUQ. Not sure if ealier engines can be converted to DBW?

aka_kerrly

12,506 posts

241 months

Tuesday 25th May 2010
quotequote all
just realised i didnt actually post the link in my first reply....
search "QPENG" they have a table that shows all the 20vt applications and details which are DBW which arent which are VVT which arent etc.

Oh and you can convert non DBW to DBW by fitting the correct throttle body. AGU 150hp early 20vt engines were NOT DBW and have the bigger inlet/exhaust ports and better head design than later models.

dave

Tame Technician

2,467 posts

235 months

Tuesday 25th May 2010
quotequote all
Turbo is always the first thing to fail in a no oil pressure situation, cams nip up just after that. Make sure you check the Turbo before you fit the engine.


sparkieboy29

Original Poster:

5 posts

198 months

Tuesday 25th May 2010
quotequote all
Thanks for all the advice I'm not sure how to check the turbo in the current state of the engine, as I was not driving the car at the time and asking my dad what happened I may as well be speaking Chinese !.. As he knows nothing about cars

Tame Technician

2,467 posts

235 months

Tuesday 25th May 2010
quotequote all
Only way to test the turbo with the engine not drivable is to take a boost pipe off, the one that goes to the inlet part of the turbo, and feel the shaft, should rotate freely with no significant up/down play.

With no oil pressure long enough to nip up the cams, I would expect its either siezed solid and wont rotate or to have about 10mm of up and down movement.

As you say it may have been only the oil ways to the cams that were clogged, but thats not normally what happens in my experience.

Ask you dad, did a red picture of an oil-can come up on the dash.

Then show him this http://www.pistonheads.com/gassing/topic.asp?h=0&a...


sparkieboy29

Original Poster:

5 posts

198 months

Tuesday 25th May 2010
quotequote all
Yes the red oil light come up on the dash and it told him to stop but did he !..... His excuse how was I going to get home ! Could of called me and the Rac would of done that !

sparkieboy29

Original Poster:

5 posts

198 months

Sunday 12th September 2010
quotequote all
So other than fitting an aum engine back in the car,can i look for another engine code which is diffrent and fit it straight in place of the knackered aum unit ?
cheers
Andy