Passat 2.0TDI Running rough after new injector
Passat 2.0TDI Running rough after new injector
Author
Discussion

armada

Original Poster:

4 posts

196 months

Sunday 25th July 2010
quotequote all
Morning all,
First post so be gentle!
`56 Passat Est 140 (bkp engine)

Ive just had a new injector fitted after a breakdown last weekend and since then engine is not running right.
Tick over is fine but when starting out from cold the engine is very rough, very much like misfiring. This continues up til 2000rpm.
When the engine is warm pulling away is fine but when traveling at a constant speed at around 1500 to 2000rmp the engine feels rough and unbalanced.

Before the injector went the car ran perfectly and smooth. Doubt anything to do with DMF.

Took the car back to the indi VW garage. Put it on the very posh laptop. No fault codes. Ran compression test - fine, Tested injectors at idle - came out as-
1 = -1.54
2 = -1.20
3 = 0.30
4 = 1.52(no4 was new injector)

They are within spec but to my mind ther is some big difference between 1 and 4.

As the problem is only when the engine is under load this is when it needs testing but mec says he cant!!

Thanks

Chris


Edited by armada on Sunday 25th July 02:01

Tame Technician

2,467 posts

235 months

Sunday 25th July 2010
quotequote all
I've had this before when I've done an injector on a PD engine.

Remove and refit the injector again, its either not seated properly, or the rocker shaft wasnt adjusted properly.

There is a special tool that presses the injector hard into potision and holds them down while you torque up the bolts (there really thins bolts only about 5nm)

Most people dont use the tool, which is ok, but you have to be sure the injector is fully pushes down before tightening up the bolts.



armada

Original Poster:

4 posts

196 months

Sunday 25th July 2010
quotequote all
Thanks for your reply. I was hoping you would see my post as you seem to know a fair bit about these engines.

So how does it effect the engine if not seated properly? I have to drive to the airport on monday and i dont want to damage the engine.
Regarding the injector values i posted, could the higher reading on inj 4 just be because it is new?


Thanks agian for you help. Im away for a couple of weeks but will post back when i take it in ang try to get it fixed.

Chris


Gurbinder

241 posts

232 months

Sunday 25th July 2010
quotequote all
I would have changed the injector wiring loom at the same time as this breaks up when being moved to have the injector replaced.

armada

Original Poster:

4 posts

196 months

Sunday 25th July 2010
quotequote all
Yeah the loom was changed at the same time. Whoever thought that putting the loom in with all that hot oil wants shooting.
The cars going in when i get back off holiday, ill post back when i get some news

Chris

Tame Technician

2,467 posts

235 months

Monday 26th July 2010
quotequote all
armada said:
Thanks for your reply. I was hoping you would see my post as you seem to know a fair bit about these engines.

So how does it effect the engine if not seated properly? I have to drive to the airport on monday and i dont want to damage the engine.
Regarding the injector values i posted, could the higher reading on inj 4 just be because it is new?


Thanks agian for you help. Im away for a couple of weeks but will post back when i take it in ang try to get it fixed.

Chris
Reading number 4 is higher because its working harder to compensate for not being in propperly. I'm sure it will be fine to use for a few weeks.

The only possible problem of running it like this is the fuel tank will get some engine oil in it, Exhaust may blue smoke as it burns this oil (isnt concentraite enough to cause any read harm). Keep an eye on the oil level, if its start to rise, then diesel is getting in the oil, this is alot more serious, but alot less common, just keep an eye on the level.

If none of this is making any scence I'll do a big explanation of PD injection when I get a bit more time.

bit back ground info here
http://www.pistonheads.com/gassing/topic.asp?h=0&a...

http://www.pistonheads.com/gassing/topic.asp?h=0&a...


armada

Original Poster:

4 posts

196 months

Wednesday 18th August 2010
quotequote all
Well. Took the car in on Monday evening and picked it up early this morning, all fixed and running well. Aparantly TPS had sent the wrong injector but in the right box!?!
Considering it took TPS 2 days to send out the original injector, the garage did very well in removing old injector, requesting new injector, getting it fitted and tested in a day when they are snowed under!

My money is on the injector wasnt seated correctly and they refitted it properly!

Cheers for the help.

Chris

extra230

3 posts

194 months

Saturday 25th September 2010
quotequote all
i have a problem with my 2006 passat, diagnostics are showing no3 injector fault, the signal to it is quite distorted, any ideas? only symptom is a slight misfire.

extra230

3 posts

194 months

Thursday 21st October 2010
quotequote all
extra230 said:
i have a problem with my 2006 passat, diagnostics are showing no3 injector fault, the signal to it is quite distorted, any ideas? only symptom is a slight misfire.
injector loom replaced, problem still exists ie slight misfire between 1000-2000 rpm