Audi A4 2.5 V6 Diesel - Turbo Failure
Audi A4 2.5 V6 Diesel - Turbo Failure
Author
Discussion

flat-planedCrank

Original Poster:

3,697 posts

234 months

Saturday 14th August 2010
quotequote all
Hi all,


Looking for a bit of advice smile


Had a turbo failure on an A4 2.5l V6 Diesel (180ps). Car lost power, was stopped pretty quickly, AA called. Closer inspection relieved that the main shaft in the turbo was loose - pretty sure its not supposed to be... The engine would appear to run ok (massively short on power of course) so I'm guessing its not a failed oil pump causing the issue?

Any idea for cost of replacement / fitting? I know its hard to say without knowing if bits of the blades got sucked into the engine, etc. but ball-park figures?

Would you take it to a main dealer for repair?


Thanks for the help guys smile

Edited by flat-planedCrank on Sunday 15th August 13:30

flat-planedCrank

Original Poster:

3,697 posts

234 months

Sunday 15th August 2010
quotequote all
Sorry to bump this, but we need to make a decision soon frown

Thanks guys.

Cupramax

11,007 posts

283 months

Sunday 15th August 2010
quotequote all
I'd guess you can get a recon turbo or one from a breaker for a couple of hundred notes or so, fitting would be 4 hours ish. Overall cost will be down to where you get it fixed, dealer will be big money, specialist may be do-able for reasonable dosh The problem you may find is the intercooler is likely be full of oil if the turbos fubarred, if the engine sounds OK otherwise its unlikely to have ingested anything.

Justin S

3,658 posts

292 months

Sunday 15th August 2010
quotequote all
quite a long journey from the turbo, through 2 intercoolers and onto the inlet manifold for anything to be ingested. I believe those are variable vane turbo's and would personally get the one you have overhauled at a specialist, as you could get a second hand one in as bad a condition as the one already on the car..................

heebeegeetee

30,257 posts

279 months

Sunday 15th August 2010
quotequote all
I wonder if it would be worth contacting a diesel engine specialist in your area. They would be able to advise on where best to source a replacement turbo - i would have thought a proper car breaker, as opposed to your typical 'scrappy' - but also advise on any possible engine damage and could give yours a compression test, which would need to be the first test to do i would have thought.

Tame Technician

2,467 posts

235 months

Sunday 15th August 2010
quotequote all
Expect to pay approx £1000+ if done at a main dealer.

New warratied part are available from euro car parts GSF etc if the main price is too high.

http://www.eurocarparts.com/ecp/c/Audi_A4_2.5_2002...

http://www.eurocarparts.com/ecp/c/Audi_A4_2.5_2002...

Most important thing is to check the oil feed to the turbo and the rest of the engine. Could be a simple turbo failure, but if the oil feed is blocked or damaged, you will just blow up the new one when fitted.


cptsideways

13,895 posts

283 months

Sunday 15th August 2010
quotequote all
Give Grahame at Universal Turbo's a ring, they have them refurbed in stock for next day delivery, price wise I guess £6-700 ish would be the norm. Mention Declan sent you & that might help smile

http://www.universal-turbos.com/

flat-planedCrank

Original Poster:

3,697 posts

234 months

Sunday 15th August 2010
quotequote all
Thanks for the help and advice guys, appreciated smile


What would you say were the chances that its just a turbo failure rather than the result of an oil issue? (car has done about 70k miles).



Cheers.

istoo

2,365 posts

233 months

Monday 16th August 2010
quotequote all
Agree with TT check the oil feed to the turbo, ie see if they are blocked, poor flow & check the pickup in the sump.
I have blown a K03 on a 1.8T with the feed hoses being nion blocked after 100k. The pickup in the sump was also very nearly blocked with sludge which wasnt helping either. I seem to think its a garrett unit on the AKE/BAU

cptsideways

13,895 posts

283 months

Monday 16th August 2010
quotequote all
It's usually caused by the VATN unit failing & it overboosting/overspooling which craps the bearings or sends it into hyperspace speeds & hence shaft failure. Its rarely an oiling issue on these

Tame Technician

2,467 posts

235 months

Monday 16th August 2010
quotequote all
cptsideways said:
It's usually caused by the VATN unit failing & it overboosting/overspooling which craps the bearings or sends it into hyperspace speeds & hence shaft failure. Its rarely an oiling issue on these
Agree 100% with the above. But while you are replacing it, its strongly advise you "check" the oil delivery is ok.