ESP Problem on A6 Quattro (2002)
Discussion
For some reason my ESP (possibly EDL) keeps kicking in and trying to brake the front passenger wheel.
All 4 tyres are new so I don't think it can be an uneven tyre wear issue.
Does anyone know how I might be able to fix it or at least disable the ESP/EDL until I can get to a garage to have it sorted?
All 4 tyres are new so I don't think it can be an uneven tyre wear issue.
Does anyone know how I might be able to fix it or at least disable the ESP/EDL until I can get to a garage to have it sorted?
Cupramax said:
ABS wheel sensors on that wheel would be the first place I'd look, but you'd be well advised to get someone with VAGCOM to see if its logging errors first.
Thanks will pop into my local garage and see if they can see any.944fan said:
There is a button on the centre console to switch of the ESP. Does that not work?
No it doesn't solve it at all.so when you say your ESP keeps trying to brake that wheel do you mean it is flashing the light up on the dash to say it is stepping in, or is it your assumption that because that corner is braking without any effort from yourself that it is the ESP?
personally, I wouldn't pay someone to bleed my brakes if they were binding, never heard of that as a cure before. Disassemble the brakes, clean the carriers, slides and pads (where they sit in the carrier not the friction surface) with a wire brush, push the pistons back the hole way and then reassemble with plenty of the relevant greases/copper slip etc.
as for a new servo.... hhmm... all a servo does it aid the effort you apply when pressing the brake pedal, so i can't see how a servo could cause brakes to bind. especially considering a servo won't provide any assistance when the throttle isn't closed (that is only relevant to petrol models) so if it is binding when you are using any throttle, it surely can't be the servo!
personally, I wouldn't pay someone to bleed my brakes if they were binding, never heard of that as a cure before. Disassemble the brakes, clean the carriers, slides and pads (where they sit in the carrier not the friction surface) with a wire brush, push the pistons back the hole way and then reassemble with plenty of the relevant greases/copper slip etc.
as for a new servo.... hhmm... all a servo does it aid the effort you apply when pressing the brake pedal, so i can't see how a servo could cause brakes to bind. especially considering a servo won't provide any assistance when the throttle isn't closed (that is only relevant to petrol models) so if it is binding when you are using any throttle, it surely can't be the servo!
Cost Captain said:
so when you say your ESP keeps trying to brake that wheel do you mean it is flashing the light up on the dash to say it is stepping in, or is it your assumption that because that corner is braking without any effort from yourself that it is the ESP?
I initially said it was the ESP braking one wheel as that was how it felt when I was driving and no there was no light on the dash flashing. Upon investigation when the car was on the lift reality was that it was not possible to turn any of the wheels by hand.Cost Captain said:
personally, I wouldn't pay someone to bleed my brakes if they were binding, never heard of that as a cure before. Disassemble the brakes, clean the carriers, slides and pads (where they sit in the carrier not the friction surface) with a wire brush, push the pistons back the hole way and then reassemble with plenty of the relevant greases/copper slip etc.
Perhaps my bad explanation, during investigation they removed the ESP controller completely and the brakes were still "binding". They then dismantled one of the calipers (front passenger side as that in my non-technical oppinion was the worst offender and I was needing to get to London last night) they cleaned and greased it up and put it back on with a view that if they cured the binding on one wheel then that was the solution on the other three. It didn't.Cost Captain said:
as for a new servo.... hhmm... all a servo does it aid the effort you apply when pressing the brake pedal, so i can't see how a servo could cause brakes to bind. especially considering a servo won't provide any assistance when the throttle isn't closed (that is only relevant to petrol models) so if it is binding when you are using any throttle, it surely can't be the servo!
Their thoughts/my non technical understanding/interpretation is that; when you push the brake pedal the servo creates a vacuum which aids braking by forcing more brake fluid down the lines to the caliper pistons and when you lift off the pedal the vacuum is reversed effectively sucking the brake fluid back. Therefore if the servo has a problem (with vacuum) when you brake it helps but if not functioning correctly doesn't suck back the fluid. The way they could release the pressure in the braking system was by having the fluid resevoir open and cracking the bleed nipple on one of the calipers.Does this sound plausible?
(They did say that in their experience this wasn't an uncommon issue with the server but I did take that with a pinch of salt... but perhaps if cammy33 has heard of same symptoms, cause and fix then perhaps I should get the salt jar back out and replace the pinch!!)
Gassing Station | Audi, Seat, Skoda & VW | Top of Page | What's New | My Stuff


