Brrrmmm....tschhh!
Author
Discussion

HereBeMonsters

Original Poster:

14,180 posts

213 months

Wednesday 13th October 2010
quotequote all
Due to remap on my Mk1 Octavia vRS (1.8T) I apparently need a better dump valve. Any recommendations? I need a place who can fit it as well, in the Southampton area.

7heo

331 posts

229 months

Wednesday 13th October 2010
quotequote all
JKM Down in Porsmouth. Give them call and they should be able to sort you out with a DV and fitting - 02392 639933 http://www.jkm.org.uk Have used them on several occasions now and always found them to be very professional and helpful.

HereBeMonsters

Original Poster:

14,180 posts

213 months

Wednesday 13th October 2010
quotequote all
7heo said:
JKM Down in Porsmouth. Give them call and they should be able to sort you out with a DV and fitting - 02392 639933 http://www.jkm.org.uk Have used them on several occasions now and always found them to be very professional and helpful.
Oh cheers for that, I think I've got a rolling road session booked with them soon. Didn't realise they were VAG tuners...

7heo

331 posts

229 months

Wednesday 13th October 2010
quotequote all
I'm down there on Saturday for an RR day with my golf.

Jim one of the owners has a Mk2 Octavia VRS as a project car.

Cupramax

11,007 posts

283 months

Wednesday 13th October 2010
quotequote all
HereBeMonsters said:
Due to remap on my Mk1 Octavia vRS (1.8T) I apparently need a better dump valve.
You dont, I ran a remapped Leon Cupra R remapped by Revo for 3 years with zero dv problems. You'd be best advised to fit a new OEM one to remove the chance that the increased boost will cause problems with a worn old unit.

HereBeMonsters

Original Poster:

14,180 posts

213 months

Wednesday 13th October 2010
quotequote all
Cupramax said:
HereBeMonsters said:
Due to remap on my Mk1 Octavia vRS (1.8T) I apparently need a better dump valve.
You dont, I ran a remapped Leon Cupra R remapped by Revo for 3 years with zero dv problems. You'd be best advised to fit a new OEM one to remove the chance that the increased boost will cause problems with a worn old unit.
From what I've read the OEM unit uses a rubber diaphragm and is prone to failure. The Forge unit I've seen is only a little bit more expensive, has a proper piston arrangement and apparently gives better performance as well.

Dr G

16,014 posts

273 months

Wednesday 13th October 2010
quotequote all
Have Regal (Southampton) fit a Forge one for you; the small extra spend is worth it for peace of mind.

HereBeMonsters

Original Poster:

14,180 posts

213 months

Wednesday 13th October 2010
quotequote all
Dr G said:
Have Regal (Southampton) fit a Forge one for you; the small extra spend is worth it for peace of mind.
Do you rate Regal? I've only ever seen them driving around in Barry Vauxhalls. They were also rude to me on the phone when I was asking about Corsa suspension upgrades. That was years ago though.

FamilyDub

3,587 posts

196 months

Wednesday 13th October 2010
quotequote all
Be careful on your terminology, here.

Is it a diverter valve you are talking about - i.e. references to torn diaphragms - or a noisy dump valve?

A diverter valve manages boost pressure, but is actually quite silent. If you want the whole McDonalds car park 'brrrreemmm, paaaarrrp, tssschhh!' effect, then it's a dump valve you want.

HereBeMonsters

Original Poster:

14,180 posts

213 months

Wednesday 13th October 2010
quotequote all
FamilyDub said:
Be careful on your terminology, here.

Is it a diverter valve you are talking about - i.e. references to torn diaphragms - or a noisy dump valve?

A diverter valve manages boost pressure, but is actually quite silent. If you want the whole McDonalds car park 'brrrreemmm, paaaarrrp, tssschhh!' effect, then it's a dump valve you want.
I thought there were two types of dump valve - atmospheric and recirculating? The Forge I'm looking at is a recirc. kind I believe, but I hear still produces a small "tssch" noise when operating.

Certainly not looking for the Barry effect. Doubt a 1.8 making in the region of 210-220bhp needs an atmospheric DV!

FamilyDub

3,587 posts

196 months

Wednesday 13th October 2010
quotequote all
^^^ Yep, you're right.

Most people don't know this difference exists, though. thumbup


Dr G

16,014 posts

273 months

Wednesday 13th October 2010
quotequote all
HereBeMonsters said:
Dr G said:
Have Regal (Southampton) fit a Forge one for you; the small extra spend is worth it for peace of mind.
Do you rate Regal? I've only ever seen them driving around in Barry Vauxhalls. They were also rude to me on the phone when I was asking about Corsa suspension upgrades. That was years ago though.
Barrying Vauxhalls is indeed a large chunk of their market but they do good work and I know a few of the guys down there quite well.

Their MK5 GTI won the VWDRC a couple of years ago and their blue MK5 is utterly and absolutely terrifying, it makes RS6 type power.

FamilyDub

3,587 posts

196 months

Wednesday 13th October 2010
quotequote all
Dr G said:
...their blue MK5 is utterly and absolutely terrifying, it makes RS6 type power.
^^^ yum

snowmuncher

786 posts

194 months

Thursday 14th October 2010
quotequote all
HereBeMonsters said:
... Doubt a 1.8 making in the region of 210-220bhp needs an atmospheric DV!
For the 1.8T 20v you want a Diverter Valve - recirculating type

As well as the Forge 007P, there is also the CompBrake unit (which comes with tuning 2x springs).

briskoda.net thread

JB!

5,255 posts

211 months

Thursday 14th October 2010
quotequote all
I shat 2x rubber diaphram units when running 18 psi.

A forge 007p is a nice upgrade, get the right spring for your boost pressure. It will make a small atmospheric noise if you run an open filter.

You CANNOT run full atmospheric units with factory management and sensors. The system relies on the air being recirculated back past certain sensors.

You can fit a forge in 5-10 mins, it's 2 jubilee clips and some vacum pipe. The hardest part is replacing the vacum pipe, use boiling water to heat the ends to help push it over the required fittings.

HereBeMonsters

Original Poster:

14,180 posts

213 months

Thursday 14th October 2010
quotequote all
snowmuncher said:
HereBeMonsters said:
... Doubt a 1.8 making in the region of 210-220bhp needs an atmospheric DV!
For the 1.8T 20v you want a Diverter Valve - recirculating type

As well as the Forge 007P, there is also the CompBrake unit (which comes with tuning 2x springs).

briskoda.net thread
Cheers, briskoda's search function is rubbish - I've been looking all over there for advice!

So am I right in that a recirc dump valve can also be called a diverter valve? One and the same thing? I'm new to forced induction!

snowmuncher

786 posts

194 months

Thursday 14th October 2010
quotequote all
HereBeMonsters said:
... briskoda's search function is rubbish ...
Indead it is - so use google to search briskoda instead

In the google search box use the following format:

example said:
diverter+valve site:briskoda.net
Example

FamilyDub

3,587 posts

196 months

Thursday 14th October 2010
quotequote all
HereBeMonsters said:
So am I right in that a recirc dump valve can also be called a diverter valve? One and the same thing?
^^^ Yes, hence my first post in this thread. thumbup

Loads of people - even at stage 2+! - still run an OEM valve on the 2.0T, rather than the Forge one. Just make sure it's a piston type valve.

It's your choice, but as I said earlier, the OEM part will be half the price and just as effective.

I did this upgrade on my 2.0T and the OEM part was £46 + VAT. The forget part is over £100.

HereBeMonsters said:
I'm new to forced induction!
^^^ turbos, FTMFW!

snowmuncher

786 posts

194 months

Thursday 14th October 2010
quotequote all
FamilyDub said:
Loads of people - even at stage 2+! - still run an OEM valve on the 2.0T, rather than the Forge one. Just make sure it's a piston type valve.
The piston type can be found on the BAM engined vehicles such as the S3, TT (225bhp) and Leon Cupra-R

Yep its cheaper than the Forge, not that much cheaper than the CompBrake, and cann't be tuned.
Its also not as physically strong as the metal ones.

Just be careful with "recirc dump valve" - forge do a unit which is both circ and dump (I believe Bailey do a similar unit - both designed to make noise, not performance).
"Diverter Valve" is the correct terminology - "dumping" means to atmosphere - "recirc" means back into the system.


JB!

5,255 posts

211 months

Thursday 14th October 2010
quotequote all
FamilyDub said:
HereBeMonsters said:
So am I right in that a recirc dump valve can also be called a diverter valve? One and the same thing?
^^^ Yes, hence my first post in this thread. thumbup

Loads of people - even at stage 2+! - still run an OEM valve on the 2.0T, rather than the Forge one. Just make sure it's a piston type valve.

It's your choice, but as I said earlier, the OEM part will be half the price and just as effective.

I did this upgrade on my 2.0T and the OEM part was £46 + VAT. The forget part is over £100.

HereBeMonsters said:
I'm new to forced induction!
^^^ turbos, FTMFW!
turbos rule!

The forge part is £70-90, shop around.

It will change the behaviour of the car. It's much more on/off boost rather than the graduation of the diaphragm ones, I prefer it.