Any sources to make electrical relays?
Any sources to make electrical relays?
Author
Discussion

nsa

Original Poster:

1,704 posts

259 months

Wednesday 4th September 2013
quotequote all
Small 12v automotive relay, the currently available product is unreliable and I'd like to have some made up to my specs. Would 1,000 units be too small for an initial order?


spikeyhead

20,660 posts

228 months

Thursday 5th September 2013
quotequote all
I'd find something suitable off the shelf. I'd be amazed if even Zonda use custom relays.

LooneyTunes

9,541 posts

189 months

Thursday 5th September 2013
quotequote all
nsa said:
Small 12v automotive relay, the currently available product is unreliable and I'd like to have some made up to my specs. Would 1,000 units be too small for an initial order?
Yes, unless you're prepared to pay through the nose.

If you're buying from a supplier who also supplies the big boys, then there's a good chance they'll be getting produced to spec in a TS-16949/QS9000 (or whatever the latest standards are) certified facility.

Assuming the spec looks OK on paper, it probably means it's something about your application that's causing failures.

Have you spoken to the manufacturer directly?

elster

17,517 posts

241 months

Sunday 8th September 2013
quotequote all
nsa said:
Small 12v automotive relay, the currently available product is unreliable and I'd like to have some made up to my specs. Would 1,000 units be too small for an initial order?
The number of Relays out there is huge and it is unlikely that yo will find a combination that isn't out there.

The unreliability could be down to manufacturer, there is not a huge amount in a relay.

eliot

12,000 posts

285 months

Sunday 8th September 2013
quotequote all
What is the application? Im sure some electronics could help.

nsa

Original Poster:

1,704 posts

259 months

Tuesday 10th September 2013
quotequote all
It's the Porsche DME relay. From what I've read the solder isn't up to holding the relay pins. When anybody has a fuel supply problem on an old Porsche they suspect the relay and replace it, for £20-30 a go. I'd like to make a guaranteed for life relay, or one that has a green LED inside to show it's working properly.

http://www.clarks-garage.com/shop-manual/fuel-05.h...


eliot

12,000 posts

285 months

Tuesday 10th September 2013
quotequote all
I assume that 85B is not a simple ground and is actually driven [to ground] by the ECU to turn the fuel pump on and off. Because if it was a simple ground, i don't see why you cant replace it with a double pole single throw relay.
You could replace it with a standard 30A relay (for the pump) and a smaller 10A relay for the injectors, but getting in a nice automotive package might be a little trickier.

nsa

Original Poster:

1,704 posts

259 months

Tuesday 10th September 2013
quotequote all
Hi. 85b is grounded by the ECU.

eliot

12,000 posts

285 months

Tuesday 10th September 2013
quotequote all
Is this the part:
http://www.ebay.co.uk/itm/PORSCHE-944-FUEL-PUMP-DM...


£23 for a relay, whilst not the cheapest is probably cheaper than you are going to be able to achieve unless making thousands of them?


LooneyTunes

9,541 posts

189 months

Tuesday 10th September 2013
quotequote all
nsa said:
I'd like to make a guaranteed for life relay
Out of interest, how much are you planning on selling them for?

I ask as the costs associated with testing for extended use may not be insignificant. Without it, if you're just going to over-engineer and take a gamble on it then you could end up on the hook for quite a few warranty claims should they start failing... and asking the manufacturer to carry the risk will result in them adjusting pricing accordingly.

spikeyhead

20,660 posts

228 months

Tuesday 10th September 2013
quotequote all
Has anyone measured the currents that they actually switch, dynamically, spikes and all?

Has anyone stripped a few down to find the failure mode?