Draytek configuration help
Discussion
I'm after some pointers on how to configure a Draytek router to deny internet access to a printer. All the fixed netowrk elements are set up with static IP addresses between 192.168.1.2 to .10 & the printer is .2. It's been fine up to now but I want to exclude the printer from internet access so it doesn't go looking for a firmware update.
Can anyone explain how best to go about this - either onthe Draytek or the printer itself.
Can anyone explain how best to go about this - either onthe Draytek or the printer itself.
Your best option would be to set up a filter rule.
- Go to Firewall > Filter Setup > Default Data Filter
- Choose an empty rule
- Enable it at the top
- For the direction, choose LAN > WAN
- For the Source IP, choose the IP of the printer (make sure it is a static IP)
- For the destination IP, choose any
- For the service type, choose any
- For the filter, choose Block Immediately
- Click OK
This should stop the printer from communicating with any external IP on any port therefore restricting it to local LAN access only.
Let me know how you get on.
- Go to Firewall > Filter Setup > Default Data Filter
- Choose an empty rule
- Enable it at the top
- For the direction, choose LAN > WAN
- For the Source IP, choose the IP of the printer (make sure it is a static IP)
- For the destination IP, choose any
- For the service type, choose any
- For the filter, choose Block Immediately
- Click OK
This should stop the printer from communicating with any external IP on any port therefore restricting it to local LAN access only.
Let me know how you get on.
A simple solution would be to manually configure the IP settings on the printer.
And then leave the "Default route" or "Default gateway" blank (no IP address) and that will prevent it from connecting to the internet but still allow local IP connections.
This assumes a basic "flat" network - e.g. no other networks in the house.
If you are unable to leave the above blank, then simply insert an IP address that's relevant to your network, but not the IP of the router.
And then leave the "Default route" or "Default gateway" blank (no IP address) and that will prevent it from connecting to the internet but still allow local IP connections.
This assumes a basic "flat" network - e.g. no other networks in the house.
If you are unable to leave the above blank, then simply insert an IP address that's relevant to your network, but not the IP of the router.
No worries, if it has other web services like apps or anything, try to browse them via the printer. Hopefully it should fail.
On the Draytek, you can turn on Web Syslog (Diagnostics>Syslog Explorer>Firewall) which should show you attempts from the printer to WAN, it should say blocked next to it. That would be conclusive.
Cheers
On the Draytek, you can turn on Web Syslog (Diagnostics>Syslog Explorer>Firewall) which should show you attempts from the printer to WAN, it should say blocked next to it. That would be conclusive.
Cheers
rob_1990 said:
No worries, if it has other web services like apps or anything, try to browse them via the printer. Hopefully it should fail.
On the Draytek, you can turn on Web Syslog (Diagnostics>Syslog Explorer>Firewall) which should show you attempts from the printer to WAN, it should say blocked next to it. That would be conclusive.
Cheers
Thanks for your help, it does indeed show the connections being blocked.On the Draytek, you can turn on Web Syslog (Diagnostics>Syslog Explorer>Firewall) which should show you attempts from the printer to WAN, it should say blocked next to it. That would be conclusive.
Cheers
Bikerjon said:
Alternatively you could simply disable auto-updates of firmware on the printer webpage. My HP has this option.
I think the printer only updates when you tell it to but I was just making sure.All this was triggered by an online article I read about Epson pushing out a firmware update that prevented the use of third party inks & with a set of Epson inks costing far more than a new printer I wanted to avoid the update. I had to ditch a Lexmark laser printer as it became uneconmic to run (the toners were chipped).
Gassing Station | Computers, Gadgets & Stuff | Top of Page | What's New | My Stuff


