Quest to improve WiFi - BT Smart Hub + BT Home WiFi mesh?
Quest to improve WiFi - BT Smart Hub + BT Home WiFi mesh?
Author
Discussion

crazy about cars

Original Poster:

4,454 posts

200 months

Sunday 4th November 2018
quotequote all
I currently use BT's Smart Hub (Home Hub 6) and whilst it's a great piece of kit the WiFi coverage is fairly poor.
I don't have a massive house nor concrete floors and brick partition walls however signal upstairs is weak.
I've recently came accross Netgear Pug In Mesh (NETGEAR EX7500-100UKS Nighthawk Mesh X4S Wall-Plug Tri-Band WiFi Range Extender)which is ideal for me as the only viable location for another AP is on a plug.
However the 5GHz band seem to work best on 100+ channel which is not available on my BT router. The main reason I've bought the extender was for my Roku upstairs and it won't connect to the extended network. I also had issues with other devices connecting and had to reboot multiple times.
Device that does connect had worse quality than the BT een though signal strength was better.
Due to this I've requested a refund.
Not sure where to go next, I'm looking at BT's Mesh system which is slightly pricier but hoping would be fully compatible.
One thing I would want is the option to either combine both 2 & 5 GHz bands or to extend them as separate networks. This is something the Netgear does but not too sure about BT Home WiFi.
Anyone here have experience on this kit or any recommendations?
I would consider upgrading the router but don't really want any fuss from BT...


Edited by crazy about cars on Sunday 4th November 16:44

anonymous-user

85 months

Sunday 4th November 2018
quotequote all
I have the bt mesh system

It just works

Straight out of the box, configure once

Job jobbed

I’d get it again

crazy about cars

Original Poster:

4,454 posts

200 months

Sunday 4th November 2018
quotequote all
JPJPJP said:
I have the bt mesh system

It just works

Straight out of the box, configure once

Job jobbed

I’d get it again
Thanks for the feedback.
Do you know if you can set separate bands (2.4 and 5GHZ) instead of just one band?
My understanding is that the BT system replaces the router wifi (which needs to be switched off) and due to legacy devices I require the WiFi to have 2 separate SSIDs showing for 2.4 and 5Ghz.

clockworks

7,818 posts

176 months

Sunday 4th November 2018
quotequote all
Home Hub 5 and BT Whole Home mesh (3 "discs") here. As posted above, it's been 100% rock solid - apart from when I made the mistake of updating the firmware, as suggested by the app. This caused months of problems with discs randomly dropping off the network. To be fair, once I found the right person to speak to, BT sent me a replacement set. I've had no problems since.

crazy about cars

Original Poster:

4,454 posts

200 months

Sunday 4th November 2018
quotequote all
clockworks said:
Home Hub 5 and BT Whole Home mesh (3 "discs") here. As posted above, it's been 100% rock solid - apart from when I made the mistake of updating the firmware, as suggested by the app. This caused months of problems with discs randomly dropping off the network. To be fair, once I found the right person to speak to, BT sent me a replacement set. I've had no problems since.
Thanks for your feedback. Did you upgrade firmware again after the replacement?
Also are you getting close to the max possible WiFi speeds around the house?

anonymous-user

85 months

Sunday 4th November 2018
quotequote all
crazy about cars said:
Thanks for the feedback.
Do you know if you can set separate bands (2.4 and 5GHZ) instead of just one band?
My understanding is that the BT system replaces the router wifi (which needs to be switched off) and due to legacy devices I require the WiFi to have 2 separate SSIDs showing for 2.4 and 5Ghz.
Not sure. Mine have the same name and I don’t see an obvious way to change that

You can set up a guest network - could that be used for some devices?

Bikerjon

2,211 posts

192 months

Sunday 4th November 2018
quotequote all
Why do you need separate SSID's for 2.4 and 5? The whole point of mesh is to reduce all that faffing about! The BT mesh is actually very good for a budget system.

crazy about cars

Original Poster:

4,454 posts

200 months

Sunday 4th November 2018
quotequote all
Bikerjon said:
Why do you need separate SSID's for 2.4 and 5? The whole point of mesh is to reduce all that faffing about! The BT mesh is actually very good for a budget system.
Suppose I like to control which network the devices logs on to. Read good reviews about BT Mesh so after I get the Netgear refunded I might go for the 2 discs package. Shame I can't justify Ubiquiti...

GT03ROB

14,037 posts

252 months

Monday 5th November 2018
quotequote all
I have a problem getting the Wi-Fi signal around the house. I have concrete floors & concrete blockwalls, Hence the signal tends to get blocked. Getting a signal downstairs is not possible & it parts of the upstairs where the signal needs to go through multiple block walls. Is the BT wifi mesh likely to help or should I just go with a powerline Wi-Fi for downstairs?

clockworks

7,818 posts

176 months

Monday 5th November 2018
quotequote all
crazy about cars said:
Thanks for your feedback. Did you upgrade firmware again after the replacement?
Also are you getting close to the max possible WiFi speeds around the house?
The replacement set came with a letter advising against trying a firmware upgrade until I was contacted to say the problem had been fixed.