partition software
Author
Discussion

munky

Original Poster:

5,328 posts

279 months

Sunday 10th June 2007
quotequote all
Afternoon,
Is there any free software out there that I can use to create a partition.. after scary blue screen moment after hard drive corruption (she turned the power off accidentally when machine was running), I bought a spare HDD for the girlfriend's PC, repaired XP on the original drive but now want to partition the new (bigger) drive, install XP on the partition, use another partition for essential data and then back up that section regularly to the old drive, which seems to be working again.. and while we're here what's the easiest way of mirroring the data partition onto the old drive? thanks!

Edited by munky on Sunday 10th June 12:10

ThePassenger

6,962 posts

266 months

Sunday 10th June 2007
quotequote all
I think, gparted will resize NTFS volumes. Do a google for "gparted livecd" and you should find one.
It is best to defrag (twice knowing Windows) and run a chkdsk before resizing/paritioning, this allows for the maximum shrinkage and makes sure the volume is in no way damaged (which will really spaz Windows out if you resize).

tank slapper

7,949 posts

314 months

Sunday 10th June 2007
quotequote all
ThePassenger said:
I think, gparted will resize NTFS volumes. Do a google for "gparted livecd" and you should find one.
It is best to defrag (twice knowing Windows) and run a chkdsk before resizing/paritioning, this allows for the maximum shrinkage and makes sure the volume is in no way damaged (which will really spaz Windows out if you resize).
Yes, it definately does. I have used it to resize XP partitions with no problems.

sadako

7,080 posts

269 months

Sunday 10th June 2007
quotequote all
The only thing i've found is, gparted is good at making the ntfs partitions smaller but not at making them bigger.

munky

Original Poster:

5,328 posts

279 months

Tuesday 12th June 2007
quotequote all
Thanks.. chkdsk / defrag shouldn't be necessary as it's a new disk. SO far it's still empty, as an interim measure I repaired XP on the old disk, which left me back at SP1 and had quite a lot of trouble getting SP2 to install but done now. Oddly then IE6 wouldn't work, displaying "application error" when attempting to load any other site other than that named as the homepage. Fixed that, then got IE7 installed again. PITA, windows.

Anyway, follow-up question, how would I install windows on the new disk.. say I install on F:, how do I ensure it then loads windows from F: and not C: (wouldn't want to wipe XP from c: until I know it's working ok from Fsmile - do I need to change any .ini files or will it realise there are 2 installations and give me a choice on boot? Or should I install on F:, disable C: in bios and hope for the best?

Next question - how do I reassign drive letters?
thanks!

slapmatt

1,132 posts

253 months

Tuesday 12th June 2007
quotequote all
munky said:
Anyway, follow-up question, how would I install windows on the new disk.. say I install on F:, how do I ensure it then loads windows from F: and not C: (wouldn't want to wipe XP from c: until I know it's working ok from Fsmile - do I need to change any .ini files or will it realise there are 2 installations and give me a choice on boot? Or should I install on F:, disable C: in bios and hope for the best?

Next question - how do I reassign drive letters?
thanks!
Take your old HD out. Set your new HD to "master" on the jumper setting and put it in your PC. Boot up from a Windows CD and install it onto your new HD in the partition you want.

Then...

Set your old HD to "slave" put that in your PC along side of your new HD and Windows will assign drive letters based upon the HDs being set as slave and master.

munky

Original Poster:

5,328 posts

279 months

Tuesday 12th June 2007
quotequote all
Will give that a go - thanks. Had set both drives to "cable select" and put new drive in position 0 and new one in position 1 but it didn't like that when trying to boot from XP CD.. but then I realised the new drive wasn't formatted so now it is, it could well work..

munky

Original Poster:

5,328 posts

279 months

Saturday 30th June 2007
quotequote all
downloaded gparted, how on earth do I run it? Downloaded one version, as a bz2 file, found some software to open that, which produced a tar file, got some software to unzip that, only to find a bunch of files, none of them executable. Then tried the livecd version, which downloads as an ISO file which, when run, insists on burning some files onto a CDR, which again don't turn out to be executable files so I've absolutely no idea what to do with it?

ThePassenger

6,962 posts

266 months

Saturday 30th June 2007
quotequote all
munky said:
downloaded gparted, how on earth do I run it? Downloaded one version, as a bz2 file, found some software to open that, which produced a tar file, got some software to unzip that, only to find a bunch of files, none of them executable. Then tried the livecd version, which downloads as an ISO file which, when run, insists on burning some files onto a CDR, which again don't turn out to be executable files so I've absolutely no idea what to do with it?
Yes, let it burn the ISO to a CDR. Then reboot the computer and boot from the CD you just created. It should jump up and go 'hello'.

munky

Original Poster:

5,328 posts

279 months

Sunday 1st July 2007
quotequote all
Ah, righty ho. was about to try that but then re-discovered XP's built-in partitioning tool. Had seen it before years ago but forgotten where it was.

Seems the old HDD has a 39Mb partition without a drive letter used for recovery, called 'EISA configuration' but I can't find any way of re-creating that on the new drive - well, I can create a partition of course but don't see how to make it a recovery disk. Think I'll just leave that partition intact on the old drive (now the slave) just in case.