NAT Settings??
Author
Discussion

GreigR

Original Poster:

765 posts

237 months

Wednesday 27th June 2007
quotequote all
Hi Guys

Just a quick question, how do I change my NAT settings?


ThePassenger

6,962 posts

266 months

Wednesday 27th June 2007
quotequote all
To do what exactly?

For the most part NAT (Network Address Translation) is the router translating 192.168.0.x to <outbound IP> and tracking connections to punt the right data to the right machine. Usually it only has on/off as settings.

GreigR

Original Poster:

765 posts

237 months

Wednesday 27th June 2007
quotequote all
At the moment I use my Xbox 360 wireless with my router, I cannot join any other games online but I can create new ones fine. I've been told that my NAT setting is likely to be set on strict which is causing the problems.

Hope that makes a little sense?

Thanks

Brink

1,505 posts

239 months

Wednesday 27th June 2007
quotequote all
Some routers are more configurable than others. Having said that, you might have to buy a more expensive one!

Brink

1,505 posts

239 months

Wednesday 27th June 2007
quotequote all
Just checked my own router and yes, I can change mine; but it's buried rather deep in the config pages.

malman

2,258 posts

290 months

Wednesday 27th June 2007
quotequote all
most home routers allow all outbound traffic - I would be surprised if your xbox360 required any inbound port forwards to join an external game.

Network Address Translation basically translates your xbox360 internal IP address to an ISP assigned internet ipaddress at your router. It works for multiple devices at the same time (PC etc) thus allowing you to have lots of things on 1 single IP address as far as the internet is concerned.

what make/model of router is it?


GreigR

Original Poster:

765 posts

237 months

Wednesday 27th June 2007
quotequote all
Thanks for the advise. It's a Zyxel prestige 600 series.


malman

2,258 posts

290 months

Wednesday 27th June 2007
quotequote all
try this from here


ZyXEL Prestige 600 Series

You need to enable UPnP to ensure this router has an Open NAT, there are three options to use and you need to use them all as follows:-

* http://192.168.1.1/
* Find the "UPnP" settings.
* Enable the Universal Plug and Play(UPnP) Service
* Enable Allow users to make configuration changes through UPnP
* Enable Allow UPnP to pass through Firewall
* Save the settings, Reboot the router and try again

GreigR

Original Poster:

765 posts

237 months

Wednesday 27th June 2007
quotequote all
Thanks, I'll give that a try.


GreigR

Original Poster:

765 posts

237 months

Wednesday 27th June 2007
quotequote all
malman said:
try this from here


ZyXEL Prestige 600 Series

You need to enable UPnP to ensure this router has an Open NAT, there are three options to use and you need to use them all as follows:-

* http://192.168.1.1/
* Find the "UPnP" settings.
* Enable the Universal Plug and Play(UPnP) Service
* Enable Allow users to make configuration changes through UPnP
* Enable Allow UPnP to pass through Firewall
* Save the settings, Reboot the router and try again
Strange, even when I click on the link http://192.168.1.1/, all I get is "This page cannot be displayed"

Help....

Leithen

14,167 posts

298 months

Wednesday 27th June 2007
quotequote all
The comma at the end of the link is the problem - enter 192.168.1.1 into your url address bar.

GreigR

Original Poster:

765 posts

237 months

Thursday 28th June 2007
quotequote all
Leithen said:
The comma at the end of the link is the problem - enter 192.168.1.1 into your url address bar.
No, same problem.


Leithen

14,167 posts

298 months

Thursday 28th June 2007
quotequote all
Go to the Edit Network Setting screen in the xbox - what does the Gateway IP read as?

neil_bolton

17,113 posts

295 months

Thursday 28th June 2007
quotequote all
GreigR said:
malman said:
try this from here


ZyXEL Prestige 600 Series

You need to enable UPnP to ensure this router has an Open NAT, there are three options to use and you need to use them all as follows:-

* http://192.168.1.1/
* Find the "UPnP" settings.
* Enable the Universal Plug and Play(UPnP) Service
* Enable Allow users to make configuration changes through UPnP
* Enable Allow UPnP to pass through Firewall
* Save the settings, Reboot the router and try again
Strange, even when I click on the link http://192.168.1.1/, all I get is "This page cannot be displayed"

Help....
Thats the default router settings for the IP range - if you/someone have changed it then you need to figure out what it is using.

Go to Start/Run, type cmd, and then in the black box type ipconfig and press enter. The default gateway should be your router. Whack this into your web browser and configure away.

I can confirm that a Zyxel Prestige works a treat on XBox live if you enable all the PnP options within that part of the menu on the router - I have one and had exactly the same problem.

Hope that helps.

Edited by neil_bolton on Thursday 28th June 08:08

GreigR

Original Poster:

765 posts

237 months

Thursday 28th June 2007
quotequote all
neil_bolton said:
GreigR said:
malman said:
try this from here


ZyXEL Prestige 600 Series

You need to enable UPnP to ensure this router has an Open NAT, there are three options to use and you need to use them all as follows:-

* http://192.168.1.1/
* Find the "UPnP" settings.
* Enable the Universal Plug and Play(UPnP) Service
* Enable Allow users to make configuration changes through UPnP
* Enable Allow UPnP to pass through Firewall
* Save the settings, Reboot the router and try again
Strange, even when I click on the link http://192.168.1.1/, all I get is "This page cannot be displayed"

Help....
Thats the default router settings for the IP range - if you/someone have changed it then you need to figure out what it is using.

Go to Start/Run, type cmd, and then in the black box type ipconfig and press enter. The default gateway should be your router. Whack this into your web browser and configure away.

I can confirm that a Zyxel Prestige works a treat on XBox live if you enable all the PnP options within that part of the menu on the router - I have one and had exactly the same problem.

Hope that helps.

Edited by neil_bolton on Thursday 28th June 08:08
Hi Neil, I was looking forward to trying that to hopefully get it fixed but I still can't even reach the configuration page.
My settings are the following:
IP Address: 192.168.1.34
Subnet mask: 255.255.255.0
Default gateway: 192.168.1.1

When I type these into the browser all I get is "This page cannot be displayed"

Greig

Leithen

14,167 posts

298 months

Thursday 28th June 2007
quotequote all
Could be something to do with the browser perhaps? Try using a different one, or a different computer to access 192.168.1.1

If you've only got IE6 or 7 , try downloading Firefox.

If that doesn't work I'm stumped..... Perhaps connect the router directly into the back of your PC via ethernet and try creating a new network connection?

neil_bolton

17,113 posts

295 months

Friday 29th June 2007
quotequote all
GreigR said:
neil_bolton said:
GreigR said:
malman said:
try this from here


ZyXEL Prestige 600 Series

You need to enable UPnP to ensure this router has an Open NAT, there are three options to use and you need to use them all as follows:-

* http://192.168.1.1/
* Find the "UPnP" settings.
* Enable the Universal Plug and Play(UPnP) Service
* Enable Allow users to make configuration changes through UPnP
* Enable Allow UPnP to pass through Firewall
* Save the settings, Reboot the router and try again
Strange, even when I click on the link http://192.168.1.1/, all I get is "This page cannot be displayed"

Help....
Thats the default router settings for the IP range - if you/someone have changed it then you need to figure out what it is using.

Go to Start/Run, type cmd, and then in the black box type ipconfig and press enter. The default gateway should be your router. Whack this into your web browser and configure away.

I can confirm that a Zyxel Prestige works a treat on XBox live if you enable all the PnP options within that part of the menu on the router - I have one and had exactly the same problem.

Hope that helps.

Edited by neil_bolton on Thursday 28th June 08:08
Hi Neil, I was looking forward to trying that to hopefully get it fixed but I still can't even reach the configuration page.
My settings are the following:
IP Address: 192.168.1.34
Subnet mask: 255.255.255.0
Default gateway: 192.168.1.1

When I type these into the browser all I get is "This page cannot be displayed"

Greig
Sounds like you have the default settings still on the router which is fine.

However as to why you are not getting to the router?

I'm assuming your connected to the internet ok?

Can you ping 192.168.1.1?

Please check that you haven't got 'Work Offline' enabled in the IE Tools menu...

Other than that...not sure without being in front of the machine - I'm assuming that you are posting using this machine?

GreigR

Original Poster:

765 posts

237 months

Friday 29th June 2007
quotequote all
Yes I can do all that and I'm using this machine to post from.

Thanks anyway.