DVD/CD Writer
Author
Discussion

Scooby_snax

Original Poster:

1,279 posts

285 months

Friday 29th June 2007
quotequote all
How easy is it to replace an internal DVD/CD writer, the easy option is to buy an external one and connect to USB port but if it is a straightforward job replacing the internal one may have a go at that.
Any recommendations on model?
Thanks
Steve

Trooper2

6,676 posts

262 months

Friday 29th June 2007
quotequote all
Hi Scooby, I replaced an internal CD ROM drive with a DVD ROM in my HP w/windows XP about 2 years ago and found it to be very easy. There were just a few screws and one connector to deal with and my DVD writer was already set up as master so just had to plug the new drive in to make it a slave. I think that all optical drives these days are "plug & play" at least this one was, so no Drivers to install before I put the new drive in.

Here is the instruction manual that came with my drive, if you want to look it over for ease of installation:

http://www.btc.com.tw/user_manual/osd/BDV316E-e.pd...


I don't have any experience with the quality of different brands of optical drives but have heard alot of good comments on "Lite-On's" middle to upper end drives. Lite-On is supposed to make a long lasting, trouble free and quiet drive that is good value for the money.

Hope this is helpful info...smile

Edit to add: VideoHelp.com has a huge, searchable list of DVD writers that have been tested and commented on by consumers if you want to read up on a model before you buy:

http://www.videohelp.com/dvdwriters



Edited by Trooper2 on Friday 29th June 15:17

Scooby_snax

Original Poster:

1,279 posts

285 months

Friday 29th June 2007
quotequote all
Thanks Trooper...think I will give it a go

colinjm

937 posts

249 months

Friday 29th June 2007
quotequote all
Yep, very easy job. They are mostly all a standard size, so a new one should just fill the gap the old one left if your swapping them out.

Check the jumpers are right on the back of the unit, just make sure they match the old one.

tigger1

8,485 posts

252 months

Friday 29th June 2007
quotequote all
Piece of pi**.

10 miutes, max, including getting a screwdriver from the shed and putting it back.

Scraggles

7,619 posts

255 months

Friday 29th June 2007
quotequote all
Scooby_snax said:
How easy is it to replace an internal DVD/CD writer, the easy option is to buy an external one and connect to USB port but if it is a straightforward job replacing the internal one may have a go at that.
Any recommendations on model?
Thanks
Steve
upto 4 screws, usually 2 either side, remove them

remove the power lead and the data lead, slide out the drive.

take new one and do the reverse...

as for model, bought some asus one from shop for £30, most seem to be the same, find it better to run at less than the 16x, but never usually in a rush smile

Stuart G Gray

7,703 posts

259 months

Saturday 30th June 2007
quotequote all
As above, piece of piss. Get new drive, take cover off PC, see what is plugged/screwed into old drive, replace with old drive. Check jumper on back of drive for Master/slave/cable select setting is same as old drive.
Treat it as replacing throttle stepper, and you won't go far wrong. biggrin

mcflurry

9,192 posts

284 months

Saturday 30th June 2007
quotequote all
svp have the Pioneer 112D or LiteOn 20A1* drives for a tad over £20, and both come recommended smile

ThePassenger

6,962 posts

266 months

Saturday 30th June 2007
quotequote all
colinjm said:
Yep, very easy job. They are mostly all a standard size, so a new one should just fill the gap the old one left if your swapping them out.
Even laptops take a standard (albeit laptop sized) unit these days.

I'd call it a 30min job for someone who's never done it before. Most of that will be "Where did I put that bastard screw????" time biggrin