Radio signal maths question
Author
Discussion

SystemParanoia

Original Poster:

14,343 posts

229 months

Monday 3rd May 2010
quotequote all
im trying to calculate ranges and related signal level at various ranges and through varying mediums.

anyone know how to calculate these ?

for instance, if a radio signal was broadcast from geo-stationary orbit ( ~20,000miles ) how do i calculate what power i would need to signal the ground with a signal strength of at least 55 dBu


( not for any real reason, just me any my eternal quest for knowledge lol )

crmcatee

5,808 posts

258 months

Monday 3rd May 2010
quotequote all
OOooooo flashback to degree time..


Geo stationery is 36000Km.

To calculate the path loss (assuming it's not raining etc and you've got ideal transponders with no loss etc)..

link loss(down) = 20 log (4*Pi*Dist/(3/10*Freq)

This will give you what you're losing on the downward link so you can calculate what you need to be pushing out of the transponder.

Now you've that, you need to calculate what the transponders losing and then you've got to calculate the uplink loss to figure out how much signal you need to be pushing out so the satellite can actually try relay it so you can get your 55db on the ground.

All of course excluding any noise from rain etc...

dilbert

7,741 posts

262 months

Monday 3rd May 2010
quotequote all
AFAIK, in free space, it's just an inverse square law, but you'll also need to take into account antenna gains.

As for attenuation in cloud, it's going to depend on many things. Not least the frequency of transmission. To do it well, you'll need a decent cloud model.

SystemParanoia

Original Poster:

14,343 posts

229 months

Monday 3rd May 2010
quotequote all
thanks for the answers guys biggrin

would the antenna shape/size/amplification make any difference ?

dilbert

7,741 posts

262 months

Monday 3rd May 2010
quotequote all
SystemParanoia said:
thanks for the answers guys biggrin

would the antenna shape/size/amplification make any difference ?
Definitely.

What you will need to know is the antenna beamwidth, in degrees.
There is a direct relationship between the beamwidth, and the antenna gain.
I'd have to dig out a book to give you something hard and fast, and I can't be bothered to derive it. If you think about it it's obvious how the relationship works. I guess you'd not be asking the question if you didn't have it to work out the answer.

Edited by dilbert on Monday 3rd May 18:04

SystemParanoia

Original Poster:

14,343 posts

229 months

Monday 3rd May 2010
quotequote all
yeah, im just doing some calcs as i have done any maths at all since leaving college and need to get the ol grey matter moving again smile

if the info isnt immediately to hand for you.. dont worry smile

dilbert

7,741 posts

262 months

Monday 3rd May 2010
quotequote all
In practice the beamwidth is hard to measure, and important to know. It is therefore critical to be able to relate beamwidth to antenna gain. The antenna gain is easy to measure, but pretty nearly useless on it's own.

Edited by dilbert on Monday 3rd May 18:09

dilbert

7,741 posts

262 months

Monday 3rd May 2010
quotequote all
The other thing, is that the beamwidth is quite strongly related to the antenna design. So for example, if the antenna is a dish, then the beam "should" be fairly well collimated. If it's a horn, then the beam will be much wider.

The point is that there is no hard and fast rule. It all depends.

Zad

13,024 posts

267 months

Monday 3rd May 2010
quotequote all
Compared to digital and low frequency analogue, RF electronics is often akin to Voodoo. Having been a radio amateur for umpty years, and having done an electronics Masters, it still leaves me a gibbering wreck at times.

First of all, you need to know the radiating power (usually in dBm).
Then you need to know the gain from the 2 antennas in the system (in dB).
Add these together to get the effective radiated power (ERP) in dBm.
Subtract from this the path loss (in dB) due to the distance between the TX/RX.
This gives you the received power.

This ignores losses between the transmitter/receiver and antennae, and effects due to atmospherics or terrain.



This might help explain the loss as the signal propagates through space: http://en.wikipedia.org/wiki/Free-space_path_loss

dilbert

7,741 posts

262 months

Monday 3rd May 2010
quotequote all
Zad said:
Compared to digital and low frequency analogue, RF electronics is often akin to Voodoo. Having been a radio amateur for umpty years, and having done an electronics Masters, it still leaves me a gibbering wreck at times.

First of all, you need to know the radiating power (usually in dBm).
Then you need to know the gain from the 2 antennas in the system (in dB).
Add these together to get the effective radiated power (ERP) in dBm.
Subtract from this the path loss (in dB) due to the distance between the TX/RX.
This gives you the received power.

This ignores losses between the transmitter/receiver and antennae, and effects due to atmospherics or terrain.



This might help explain the loss as the signal propagates through space: http://en.wikipedia.org/wiki/Free-space_path_loss
I'm not sure that's quite right, but I do take your point.

What I mean, is that the antenna gain for a horn or a dish, is reasonable to calculate by geometry.
The gain of a ferrite rod antenna, that's fiendish by comparison. You could never make a dish for say 60KHz, but it's used nearly constantly for RF transmission. To receive, at least practically, it has to be a ferrite rod.

Edited by dilbert on Monday 3rd May 19:48