Glue for roof lining
Discussion
Hi Chaps
About 9 months ago I retrimed my Cerb to get rid of the nasty "carpet" that was my old roof lining. It had held well for a time but the spray on carpet adhesive I used has lost its effectiveness in the face of the "searing" temperatures we have been having recently (well that and driving with the windows down everywhere!).
Does anyone have any suggestions for a glue that would be better suited for this?
Thanks in advance!
Barry
About 9 months ago I retrimed my Cerb to get rid of the nasty "carpet" that was my old roof lining. It had held well for a time but the spray on carpet adhesive I used has lost its effectiveness in the face of the "searing" temperatures we have been having recently (well that and driving with the windows down everywhere!).
Does anyone have any suggestions for a glue that would be better suited for this?
Thanks in advance!
Barry
Having tried all the usual glues when I did my retrim, including the expensive high temperature impact adhesives designed for the job, the only thing I have found that has held my perforated leather (therefore heavy) headlining up on a hot day is No More Nails.
Spread it with a rake/comb spreader as you would for tile adhesive and be very careful to get your positioning right as you only get one go, but it will hold permanently.
It sounds odd but the tip was given to me by a very experienced professional upholsterer.
Spread it with a rake/comb spreader as you would for tile adhesive and be very careful to get your positioning right as you only get one go, but it will hold permanently.
It sounds odd but the tip was given to me by a very experienced professional upholsterer.
Edited by Tanguero on Friday 15th July 09:18
I foam lined my leather for a smooth finish. I found that because no more nails isn't very liquid - its more of a paste consistency - it didn't sink into the foam at all. If you need to glue upholstery foam to alcantara then you want to use a spray contact adhesive to sandwich them together first. That will hold fine because the foam layer insulates it from the direct heat of he roof. The no more nails is to then glue the foam side of the foam/alcantara sandwich to the fibreglass.
If the old foam is stuck to the roof and the alcantara has come off that, then personally I would scrape the old foam off and start again with fresh foam.
If the old foam is stuck to the roof and the alcantara has come off that, then personally I would scrape the old foam off and start again with fresh foam.
Edited by Tanguero on Friday 15th July 21:32
I had exactly the same problem last year. I tried various 'high' temp sprays for interior with no luck. the best was Evo stick which lasted the winter but as soon as the sun came out it became Evo Un-stuck lol
So following Tanguero's advice I used No Nails or a cheaper equivalent and it worked a treat. I too have the foam backed velour. Get the stuff in the plastic tube where you have to use the 'gun' adaptor thingy as its easier to control.
So following Tanguero's advice I used No Nails or a cheaper equivalent and it worked a treat. I too have the foam backed velour. Get the stuff in the plastic tube where you have to use the 'gun' adaptor thingy as its easier to control.
I didn't take mine off. I left it fixed round the front and two sides I pulled the rollbar cover off and went in through there.
It's a little more awkward applying the glue this way which is why its easier to use the tubes as you can get it in to the corners easier. But it means the lining is already positioned correctly and makes it easier to get it right first time.
After spreading the no nails about as evenly as possible use the side of spray can and working from front middle backwards and outwards pressing the lining up to the roof.
It's a little more awkward applying the glue this way which is why its easier to use the tubes as you can get it in to the corners easier. But it means the lining is already positioned correctly and makes it easier to get it right first time.
After spreading the no nails about as evenly as possible use the side of spray can and working from front middle backwards and outwards pressing the lining up to the roof.
Mad Mark said:
I didn't take mine off. I left it fixed round the front and two sides I pulled the rollbar cover off and went in through there.
It's a little more awkward applying the glue this way which is why its easier to use the tubes as you can get it in to the corners easier. But it means the lining is already positioned correctly and makes it easier to get it right first time.
After spreading the no nails about as evenly as possible use the side of spray can and working from front middle backwards and outwards pressing the lining up to the roof.
Thanks.It's a little more awkward applying the glue this way which is why its easier to use the tubes as you can get it in to the corners easier. But it means the lining is already positioned correctly and makes it easier to get it right first time.
After spreading the no nails about as evenly as possible use the side of spray can and working from front middle backwards and outwards pressing the lining up to the roof.
Gassing Station | Cerbera | Top of Page | What's New | My Stuff



