IT HAS STARTED........
Discussion
The GT3 is now off the road for some TLC, just got back from body shop for front end respray.
Removed the gearbox earlier today.
Items I am going to do:
-gearbox overhaul
-suspension overhaul
-rear brakes
-front bumper mesh out
Will post some pictures over next month or so. (work load permitting)
Mike
Removed the gearbox earlier today.
Items I am going to do:
-gearbox overhaul
-suspension overhaul
-rear brakes
-front bumper mesh out
Will post some pictures over next month or so. (work load permitting)
Mike
David Hype said:
Mike, please do post some pictures during all this. We very rarely get to see inside these beasties and I am sure all the PH boys would really appreciate the insight!
Thanks
Hi,Thanks

I will post some pictures as we progress, I have even got some upgraded steel synchromesh rings for my gearbox....along with a load of bearings
it has always had a slight bearing whine from the input shaft.Will post up when it is stripped down.
Mike
Diesel130 said:
Out of interest, why the gearbox overhaul - did something break, or do GT3 gearboxes wear out after 30K+ miles (that was the mileage of yours wasn't it)?
Hi,everything wears out, GT3/2 and TT boxes have a very small input shaft bearing that wears out quickly.
Will post pictures up.
Mike
Mike
If you're doing overhaul you should REALLY consider welding up your coolant fittings.
There's 7 places on the engine where coolant nipples are just glued in place to the castings.
These seem to be failing now with increasing frequency which would suggest glue is reaching it's lifetime.
Result is catastrophic coolant loss, usually over a rear wheel.
Not good for you and certainly not good for anyone on track at the same time if you are running coolant rather than water.
Another one for the list is to rebuild your diff with motorsport plates. The street diff is terrible as it comes.
I'd have both of these right at the top of any list I was doing.
Ref the trans. Are you going to regear while you are in there or just keep stock?
The street box can only have 3-6 changed so it's not ideal but still gives options. An 8:32 R&P is an alternative to shorten but still leaves you with the big ratio gaps.
Steel syncros are great. Cup also has an oil spray pump for the internals which makes a big difference under hard driving. The gearbox oil is also filtered on the Cup.
If you're doing overhaul you should REALLY consider welding up your coolant fittings.
There's 7 places on the engine where coolant nipples are just glued in place to the castings.
These seem to be failing now with increasing frequency which would suggest glue is reaching it's lifetime.
Result is catastrophic coolant loss, usually over a rear wheel.
Not good for you and certainly not good for anyone on track at the same time if you are running coolant rather than water.
Another one for the list is to rebuild your diff with motorsport plates. The street diff is terrible as it comes.
I'd have both of these right at the top of any list I was doing.
Ref the trans. Are you going to regear while you are in there or just keep stock?
The street box can only have 3-6 changed so it's not ideal but still gives options. An 8:32 R&P is an alternative to shorten but still leaves you with the big ratio gaps.
Steel syncros are great. Cup also has an oil spray pump for the internals which makes a big difference under hard driving. The gearbox oil is also filtered on the Cup.
I don't think it can be shrugged off as a regional variation. It's spread is all across the US and Canada and covers all of the fittings.
The US is usually ahead of these things due to the sheer size of the community and the technical nature of the discussions they have. Both are lacking here.
The only common factor seems to be the glue giving up on the fittings which would suggest either a bad batch or glue getting near it's life.
It's up to owners to work out how they view the risk and if they want to take preventative action.
For anyone tracking their car though my view is that they owe it to other drivers to either take action or run only water/waterwetter on track days.
If it pops you need the engine out anyways so it seems better to do it in a controlled fashion rather than mid season after ending stuck and needing trailered.
The US is usually ahead of these things due to the sheer size of the community and the technical nature of the discussions they have. Both are lacking here.
The only common factor seems to be the glue giving up on the fittings which would suggest either a bad batch or glue getting near it's life.
It's up to owners to work out how they view the risk and if they want to take preventative action.
For anyone tracking their car though my view is that they owe it to other drivers to either take action or run only water/waterwetter on track days.
If it pops you need the engine out anyways so it seems better to do it in a controlled fashion rather than mid season after ending stuck and needing trailered.
Mike
They only have mk2 in the US so no data to contribute for mk1.
I don't have any interaction with the UK GT3 community (is there one in that sense?) so have no idea of failures here.
From an engineering side the spread over there is enough that you can't put it down to extreme summer temps that aren't seen here.
With the factor removed there isn't any logical reason why they are seeing them there other than they have more of them. They run same coolant and same engine temps.
There's obviously plenty of people with no failures, much more than with at the moment but it is happening.
With that in mind it just seems like a smart thing for track users to deal with under the preventative category.
If you track alot or in places far from home I'd say weld them makes sense. It would suck to have one pop and leave you stranded. If you don't then just run water with water wetter over the summer. This will save your own rear if it bursts (water onto a tyre is better than coolant) and save others hitting a slick mess. Once summer and track days are over put coolant/anti freeze back in.
It wasn't meant to be a lecture/preach/rant and certainly wasn't a scaremongering exercise. I just zipped my own up and don't need to think about it again.
It was just merely out there for discussion since you were doing work over the winter to prep and upgrade the car.
They only have mk2 in the US so no data to contribute for mk1.
I don't have any interaction with the UK GT3 community (is there one in that sense?) so have no idea of failures here.
From an engineering side the spread over there is enough that you can't put it down to extreme summer temps that aren't seen here.
With the factor removed there isn't any logical reason why they are seeing them there other than they have more of them. They run same coolant and same engine temps.
There's obviously plenty of people with no failures, much more than with at the moment but it is happening.
With that in mind it just seems like a smart thing for track users to deal with under the preventative category.
If you track alot or in places far from home I'd say weld them makes sense. It would suck to have one pop and leave you stranded. If you don't then just run water with water wetter over the summer. This will save your own rear if it bursts (water onto a tyre is better than coolant) and save others hitting a slick mess. Once summer and track days are over put coolant/anti freeze back in.
It wasn't meant to be a lecture/preach/rant and certainly wasn't a scaremongering exercise. I just zipped my own up and don't need to think about it again.
It was just merely out there for discussion since you were doing work over the winter to prep and upgrade the car.
Gassing Station | Porsche General | Top of Page | What's New | My Stuff




