GT Engine Cooling Pipework...
Discussion
So after trawling the net for hours I have seen this is a worldwide fault, just not seen many reported cases in u.k....
I have decided to do my own set of pipes as a preventative measure.
Out of interest how many owners would want this mod doing ?
We have aluminium welding facilities on site.
Mike
I have decided to do my own set of pipes as a preventative measure.
Out of interest how many owners would want this mod doing ?
We have aluminium welding facilities on site.
Mike
I might be picking up a spare cup engine in which case I'll have a set needing welded somewhere.
Won't need engine dismantled in my case. I can pull the pipes off.
Fwiw I believe it's a tricky weld due to the cast alu and the glue. Folks who have welded round without pulling and cleaning up first have had the glue contaminate the weld at times apparently.
I can't weld, I just make big holes so this is purely a regurgitation. Maybe others can chime in with actual thoughts
Won't need engine dismantled in my case. I can pull the pipes off.
Fwiw I believe it's a tricky weld due to the cast alu and the glue. Folks who have welded round without pulling and cleaning up first have had the glue contaminate the weld at times apparently.
I can't weld, I just make big holes so this is purely a regurgitation. Maybe others can chime in with actual thoughts

Hi,
You would really need to remove the pipes first as said the adhesive will come to the surface and contaminate the weld pool for sure. I am no alloy welder but lucky for me my dad is!
I can manage stainless and mild steels but am still learning ally welding.
Cast welding is the worst type too as it is full of impurities so added with glue and coolant residue it will not be the nicest material to weld, but sure it will be fine.
Have you seen the pipes ? Do they just have a few mm thick wall thickness ?
Mike
You would really need to remove the pipes first as said the adhesive will come to the surface and contaminate the weld pool for sure. I am no alloy welder but lucky for me my dad is!
I can manage stainless and mild steels but am still learning ally welding.
Cast welding is the worst type too as it is full of impurities so added with glue and coolant residue it will not be the nicest material to weld, but sure it will be fine.
Have you seen the pipes ? Do they just have a few mm thick wall thickness ?
Mike
Thanks. That's still a whole load better than me haha.
Yeah I've seen the pipes. The insert piece is thin walled. Lucky if it's even 2mm. The cast much thicker.
Any welds I've seen done have melted through the insert in places where the weld itself is. This is just filed down.
I believe there's as many cars just using JB Weld as there is full welds. This negates the need to remove inserts etc. Engine temp is approx 180F so well below JBs 500F capacity.
Yeah I've seen the pipes. The insert piece is thin walled. Lucky if it's even 2mm. The cast much thicker.
Any welds I've seen done have melted through the insert in places where the weld itself is. This is just filed down.
I believe there's as many cars just using JB Weld as there is full welds. This negates the need to remove inserts etc. Engine temp is approx 180F so well below JBs 500F capacity.
sportsandclassic said:
Hi,
You would really need to remove the pipes first as said the adhesive will come to the surface and contaminate the weld pool for sure. I am no alloy welder but lucky for me my dad is!
I can manage stainless and mild steels but am still learning ally welding.
Cast welding is the worst type too as it is full of impurities so added with glue and coolant residue it will not be the nicest material to weld, but sure it will be fine.
Have you seen the pipes ? Do they just have a few mm thick wall thickness ?
Mike
Thread with pics here :You would really need to remove the pipes first as said the adhesive will come to the surface and contaminate the weld pool for sure. I am no alloy welder but lucky for me my dad is!
I can manage stainless and mild steels but am still learning ally welding.
Cast welding is the worst type too as it is full of impurities so added with glue and coolant residue it will not be the nicest material to weld, but sure it will be fine.
Have you seen the pipes ? Do they just have a few mm thick wall thickness ?
Mike
http://www.pistonheads.com/gassing/topic.asp?h=0&a...
And another method of avoiding the issue :
http://www.6speedonline.com/forums/996-turbo-gt2/2...
sportsandclassic said:
So after trawling the net for hours I have seen this is a worldwide fault, just not seen many reported cases in u.k....
I have decided to do my own set of pipes as a preventative measure.
Out of interest how many owners would want this mod doing ?
We have aluminium welding facilities on site.
Mike
Mike, we looked at this as well but in the end decided against it. We know of only one case in the UK. There are quite a lot of different solution to it and in the last three engine builds have decided not to do it. I have decided to do my own set of pipes as a preventative measure.
Out of interest how many owners would want this mod doing ?
We have aluminium welding facilities on site.
Mike
Ken
p.s. I'll have to keep my fingers crossed now as that is probably the kiss of death
Gassing Station | Porsche General | Top of Page | What's New | My Stuff


