997 Alarm question?
997 Alarm question?
Author
Discussion

George36

Original Poster:

52 posts

230 months

Wednesday 31st August 2011
quotequote all
Does anyone elses alarm beep the horn once, when armed?
Mines done this since I bought it...
According to the manual this indicates a problem!
But all doors, bonnet and engine lid cannot be opened when the alarm is armed.
Any ideas?

Below is taken from the manual:

A short signal from the alarm horn will draw your attention to the fact that the following components are not completely closed when you try to lock the vehicle:
– Driver’s door (the vehicle cannot be locked if the driver’s door is not completely closed)
– Passenger’s door
– Luggage compartment lid
– Engine compartment lid
– Glass rear hatch (Targa)
– Glove compartment


Callughan

6,313 posts

223 months

Wednesday 31st August 2011
quotequote all
Only when i have left something open

surfymark

895 posts

262 months

Wednesday 31st August 2011
quotequote all
Mine is a 996 but mine does this when I leave something open as it says. Usually I find it is the glove box or the cubby between the seats.

Maybe one of your sensors has packed up?

Mine also beeps once when disarming the alarm if the alarm has gone off while armed.

HTH
M

George36

Original Poster:

52 posts

230 months

Wednesday 31st August 2011
quotequote all
Does the Glove box have to be locked?
I'll check out the sensors on the glove box and centre console in the mean time...
Thanks

Callughan

6,313 posts

223 months

Wednesday 31st August 2011
quotequote all
Not locked just shut

Pope

2,653 posts

278 months

Wednesday 31st August 2011
quotequote all
Check the glovebox light switch is functioning, not just that the thing is shut - the switch behind the glovebox has a tendency to go out of alignment and stay 'on' - simple fix

Tip: if you're not sure, set your phone camera to record and shut it in the glovebox - if the light stays on you'll soon see smile

DavidAL

53 posts

195 months

Wednesday 31st August 2011
quotequote all
George36 said:
– Driver’s door (the vehicle cannot be locked if the driver’s door is not completely closed)
– Passenger’s door
– Luggage compartment lid
– Engine compartment lid
– Glass rear hatch (Targa)
– Glove compartment
I suspect that one of the switches/sensors on one of these elements is broken, or not adjusted correctly, so that the system thinks you have left it open...

DavidAL

53 posts

195 months

Wednesday 31st August 2011
quotequote all
George36 said:
Does the Glove box have to be locked?
I'll check out the sensors on the glove box and centre console in the mean time...
Thanks
I don't think that the centre console compartment is monitored in that way..

George36

Original Poster:

52 posts

230 months

Thursday 1st September 2011
quotequote all
Thanks for the replies guys.
I had a look last night and was expecting a plunger/push switch but couldn't see one or anything obvious...
So does anyone know what the sensors/switches look like on the doors and luggage area and where abouts located?
I'll be trying the camera trick tonight, good tip.

sportsandclassic

3,774 posts

249 months

Thursday 1st September 2011
quotequote all
Hi,

The glove box switch is concealed at rear of glove box with a metal spring band (if same as 996 ?)

The centre console switch is similar design and can be seen from top of latch area.

As for the boot and engine lids these are attached to the locks.

The door lock switches are built into the door locks.

What radio is in it ? Porsche..?

Mike

George36

Original Poster:

52 posts

230 months

Thursday 1st September 2011
quotequote all
Standard Porsche radio, PCM 2.1
Thanks for the info Mike, Hopefully it's the glove box sensor...
Looking at the online parts catalogue the 996 and 997 look a bit different, I can see the sensor on the 996 diagram but not on the 997 diagram!
I'll check it out tonight.

Tino

1,948 posts

314 months

Thursday 1st September 2011
quotequote all
Pope said:
Check the glovebox light switch is functioning, not just that the thing is shut - the switch behind the glovebox has a tendency to go out of alignment and stay 'on' - simple fix

Tip: if you're not sure, set your phone camera to record and shut it in the glovebox - if the light stays on you'll soon see smile
Thats a good Idea!
I'm gonna try it with my fridge tonight... Find the little man that switches off the light

George36

Original Poster:

52 posts

230 months

Friday 16th September 2011
quotequote all
Just thought I'd post an update.
Did the camera trick at the weekend, light was indeed staying on.
Got round to dismantling the dash today, the glove box takes ages to get out... German engineering!
Turns out the micro switch had just come away from it's mounting, reseated and it's working fine.
Slightly quicker putting it back together rolleyes

Anyway the alarm no longer beeps when locking so mission accomplished biggrin

If anyone needs a new glove box wiring harness then PM me as I have a brand new one I bought and didn't need wink

DavidAL

53 posts

195 months

Friday 16th September 2011
quotequote all
George36 said:
Just thought I'd post an update.
Did the camera trick at the weekend, light was indeed staying on.
Got round to dismantling the dash today, the glove box takes ages to get out... German engineering!
Turns out the micro switch had just come away from it's mounting, reseated and it's working fine.
Slightly quicker putting it back together rolleyes

Anyway the alarm no longer beeps when locking so mission accomplished biggrin

If anyone needs a new glove box wiring harness then PM me as I have a brand new one I bought and didn't need wink
Good news.. Always nice to hear a happy ending...

George36

Original Poster:

52 posts

230 months

Friday 16th September 2011
quotequote all
True, if only I'd taken it apart before suspecting the worst and buying the parts idea

Pope

2,653 posts

278 months

Friday 16th September 2011
quotequote all
Good news about the fix; though there is an easier way of getting to the switch......

Release the soft action plunger on the left hand side (pull it toward you at the lid end, it will unclip) and locate the lid stop on the right hand side in the lid, prise the inner lid at the lid stop to the left thereby disengaging the stop and the lid will open down to the floor. The switch is then visible and accessible.

Belated but hope this helps (next time..........)

George36

Original Poster:

52 posts

230 months

Friday 16th September 2011
quotequote all
Next time! Hopefully there won't be a next time... Thanks for the tip though.

DavidAL

53 posts

195 months

Friday 16th September 2011
quotequote all
George36 said:
True, if only I'd taken it apart before suspecting the worst and buying the parts idea
Ah, true.. Still.. Leaves it open for the Hollywood sequel style thread.. "How I sold my wiring loom" AKA "anybody wanna buy..."...

biggrin