997 GT3 geo and brakes...
997 GT3 geo and brakes...
Author
Discussion

MB 1

Original Poster:

525 posts

216 months

Saturday 3rd September 2011
quotequote all
I've had the car a few months now, and it has OEM geometry settings and Alcon front brakes with Pagid pads.

First question is on the geo, what are people using as a fast road setup? I'm struggling getting any confidence in the grip levels and feels like the back is moving around a bit. I took it to Spa a few weeks ago and couldn't get a really good feel for it. Tyre pressures all good. Was going to take it to Chris Frnaklin for full tweaking, as i'm sure I can get it changed to suit me. Certianly OEM geo feels like it's lacking in camber.

On the brakes, they are surprisingly poor in bite and overall power, which has surprised me. Again at Spa I was struggling to haul the car down, and it's similar on the road. I have been standing on them. Don't get me wrong, they are good but not what I expected. Most people told me they were monsters in the brake department... What are people using? I plan to switch to Dixcel racing, which I use on my track S2000. Not cheap, but they are phenominal!

Input appreciated.

911p

2,361 posts

211 months

Sunday 4th September 2011
quotequote all
MB 1 said:
Certianly OEM geo feels like it's lacking in camber.
I can't recommend Chris highly enough, it'll feel like a new car afterwards. Book now 'cos he has quite a waiting list.

LuckyP

6,243 posts

256 months

Sunday 4th September 2011
quotequote all
S2000 is 100kg lighter. It'll slow down quicker.

You say OEM geo. Have you had it checked? Is it noticably highter at the back?

What was the tyre wear like at Spa?

Pete

TonyB66

243 posts

201 months

Sunday 4th September 2011
quotequote all
Why don't you try some different brake pads before you go the whole hog an change the discs as well?

bobsan

495 posts

250 months

Sunday 4th September 2011
quotequote all
Alcon plus Pagid yellow's are industry standard, so before swapping change brake fluid, that can let the winning combination down badly.

clearly the vehicle lacks good geometry, should be absolutely planted and give huge confidence, there are several excellent geo specialist's in UK, CG being one of them with that extra attention to customer satisfaction.

anonymous-user

85 months

Sunday 4th September 2011
quotequote all
Back should be planted if geo and ARB settings right (ie not too stiff at back). Commonest cause of loose back end is shot diff (v common) - you will feel it under braking. Fit cup plates and it will transform braking from high speeds. Alcon up front, and standard rears are more than man enough - your problem lies elsewhere.

bobsan

495 posts

250 months

Sunday 4th September 2011
quotequote all
'Commonest cause of loose back end is shot diff'

you got that right,almost pointless getting geo sorted with a worn out diff.

Cup diff - another industry standard.

MB 1

Original Poster:

525 posts

216 months

Sunday 4th September 2011
quotequote all
Interesting replies, thanks smile

RE the S2000 brakes, it has small 4 pot front and smaller 2 pot rears so i'd imagine the proportion of the GT3 6 pots and huge discs would counteract that.

I'm sure the diff is ok, the car has only done 13k and limited track use. Any real way of checking?

Brake fluid is a good one, although it's just had a major service at OPC, before I went to Spa. Someone at Spa did suggest that one to me. I may upgrade it anyway, although the car isn't going to be used on track.

The Geo was done during the service.

Think I will start by taking it to Chris at CG (he did wonders to my track car) and see if that sorts it.

Brakes wise, maybe some fluid and different pads?

nickfrog

25,478 posts

248 months

Sunday 4th September 2011
quotequote all
I remember the S2000 brakes being quite overservoed so you may simply be used to a short travel on/off pedal whereas the Porsche will offer much more modulation at the "expense" of longer travel but without affecting overall power. Once you're used to the setup, you may actually appreciate that ability to work with braking power precisely as it's what helps keeping weight transfers to a minimum. Then again, fresh fluid and bleed would be a good idea, just in case...

Not sure about "OE" geo on a GT3 but on more humble Porsches the factory geo offers quite a wide range in both toe and camber so it needs to be refined to your needs anyway, whether it's done by CG or by one of the many other UK specialists (it's not rocket science!).

MB 1

Original Poster:

525 posts

216 months

Sunday 4th September 2011
quotequote all
That's correct, the braking feel is very different. But I was having to brake such a long way before corners it was affecting my lap times / enjoyment. I'm sure it's something simple.


bobsan

495 posts

250 months

Sunday 4th September 2011
quotequote all
Interesting replies, thanks

RE the S2000 brakes, it has small 4 pot front and smaller 2 pot rears so i'd imagine the proportion of the GT3 6 pots and huge discs would counteract that.
as said, forget what happened with the S2000, this is a whole different vehicle, loading the front is paramount in driving these things, have a look at Porsche Driving Days at Silverstone.

I'm sure the diff is ok, the car has only done 13k and limited track use. Any real way of checking?
Wrong, your diff is almost certanly shot, with gear in neutral, jack up one rear and spin the wheel, if it turns easy the diff is shot, with Cup diff you'd need to grab it with both hands and force it to turn.

Brake fluid is a good one, although it's just had a major service at OPC, before I went to Spa. Someone at Spa did suggest that one to me. I may upgrade it anyway, although the car isn't going to be used on track.
forget the lame fluid they may have used, drain and install Castrol RBF660 or Motul Racing fluid.

The Geo was done during the service.
Rubbish, the Geo was checked and found to be more or lass within factory spec, way off where you need to be.

Think I will start by taking it to Chris at CG (he did wonders to my track car) and see if that sorts it.
not before sorting the diff out.

Brakes wise, maybe some fluid and different pads?
Pagid RS29 front and rear is all you need.


MB 1

Original Poster:

525 posts

216 months

Sunday 4th September 2011
quotequote all
Bob, I stated the S2000 so that so people could see I had a point of reference. I've owned a LOT of performance cars, and given the high praise of the Porsche brakes, I feel there is something which needs improving. The car will not haul itself down as I expect it to. I went out in another GT3 at Spa too, and there was a difference.

The "wrong" statement about my diff is ridiculous. How can you possibly know?

As is the "rubbish" statment about the geo, they checked it, it was all over the shop, and corrected it. I have a print out somewhere. So careful when you say things like "rubbish" I also know the service maanger personally.

But thanks for your non aggressive views, duly noted smile

Mermaid

21,492 posts

202 months

Sunday 4th September 2011
quotequote all
bobsan said:
...




forget the lame fluid they may have used, drain and install Castrol RBF660 or Motul Racing fluid.


Rubbish, the Geo was checked and found to be more or lass within factory spec, way off where you need to be.



Brakes wise, maybe some fluid and different pads?
Pagid RS29 front and rear is all you need.
Don't these changes invalidate the Porsche warranty?

MB 1

Original Poster:

525 posts

216 months

Sunday 4th September 2011
quotequote all
Not sure about the geo, i'm sure they would use it as an argument if a suspension component failed. Brake fluid they would have a job noticing, but brakes are a definate no no. Although there are always ways around these things!

Cunno

511 posts

188 months

Sunday 4th September 2011
quotequote all
Hi MB1

Good to see you at spa in the new car.

What Bob is saying, could be quite correct.

The diff in a GT3 is known to give in early, changed mine out at about 20k miles, way over due. The road plates wear out quick, if used on track. Up grade it to Cup plates £1200 job by most indys. Porsche parts so warrenty should stand.

The geo, don't know your OPC, but my local OPC contract this work out, so never sure who's done it or how long they have spent on it. Take it to a pro and get it set up correctly, it will make a difference.

GT3 brakes are normally good straight from the factory, most people change to get away from the star cranking the factory set up suffers from. So start with a fluid change and then work upto pads disc etc.

Jon C

MB 1

Original Poster:

525 posts

216 months

Tuesday 6th September 2011
quotequote all
Thanks Jon.

Were you in the black 997?

LuckyP

6,243 posts

256 months

Tuesday 6th September 2011
quotequote all
My MR2 stops quicker than my GT3. It has way smaller brakes....but like your S2000 is lighter than the GT3 (about the same difference again as your S2000 is to the GT3). Physics is physics.

Your GT3 on the same rubber as the one you went in at SPA?


MB 1

Original Poster:

525 posts

216 months

Tuesday 6th September 2011
quotequote all
I have new rears on now (losing battle with an 8mm wide bolt!) but still the same, just feels like it's lacking bite and overall power. Will get another GT3 owner to have a go in mine to see if it's me being a fanny biggrin

Steviebeee

601 posts

214 months

Tuesday 6th September 2011
quotequote all
MB 1 said:
Will get another GT3 owner to have a go in mine to see if it's me being a fanny biggrin
lol, like the comment. Some times you just underestimate just how good a car you have smile

Slippydiff

16,503 posts

254 months

Tuesday 6th September 2011
quotequote all
My two pence worth :

An OPC wouldn't be my first port of call for a geo set up. Knowing the service manager means nothing, we wasn't the one rattling the spanners under your car was he ? smile

If you know Chris at CG well, give him a ring and ask what he thinks of geometry set ups on the majority of 997 GT3s he's seen with low miles or even straight from the factory . . . wink

So your local OPC has adjusted the geo settings ? did they also check the ride heights and corner weights ? I suspect not, in which case the piece of paper you have with your geometry settings is of little or no value whatsoever. sorry, but that's the harsh reality of it, mate of the service manager or not. frown

Diff plates are a hot potatoe, if as you say it's been tracked a few times, there's every chance the standard diff plates will be doing little or nothing. Brilliantly engineered though these cars are, the factory preload (certainly on 996 GT cars) is poor, and even some light trackday useage will reduce the preload to negligible levels.

My 68K mile GT2 diff plates being a case in point, the diff still has some preload, but for serious trackwork it would be found wanting. Matt at Fearnsport has seen many cars with plenty of track usage. When the diffs are stripped the plates are frequently in serviceable condition purely because the preload has long since disappeared so the plates have no pressure applied to them, so quite simply, they don't wear out.

Build some more preload into the diff and then they'll start to wear out ! At which point you'll wish you'd fitted the better wearing Motorsport plate pack . . . .

Brakes. Are they steels or PCCBs ? was this car tracked prior to your ownership ? if so is the car running standard OE Pagid pads (don't be fooled by their colour they could be any one of at least three different compounds) and if they are standard and the cars been tracked, they may well have been cooked by the previous owner.

Either way, if the brakes have been properly bled they should stop the car with conviction, the fluid used by your OPC will be Porsche approved , and whilst it may not be up to sustained track useage it should provide safe drama free stopping on the road under ALL conditions.

HTH