996 Gt3rs cage
Discussion
I have installed one and and not being mechanically minded it was very easy so taking out will be even easier. Just be careful though with the passenger side which has the roof bar welded to it which will make it tricky taking it out. Other than that you will have holes in the carpet in the front wells but floor mats will over come that problem.
Yep - done it before after asking a similar question on here.
Here goes...
There are two pieces to the front cage - one is the right side bar (driver's door side) from the floor to where it meets the rear cage - the other includes the left hand side (passenger side) and the cross member running from left to right above the windscreen as one piece.
There are 5 places which need to be unscrewed:
1. Floor bolts at the bottom of each front vertical bar (left and right).
2. Connecting bolts at the top rear where the front cage meets the rear cage (left and right).
3. Top right (above driver's head) where the front cross member meets the right side bar.
Having unscrewed all the bolts in the above 5 places, I find it easier to first release the connecting joint above the driver's head where the left side meets the right side. Once this is loosened, the whole front cage is a little loose and then you have just manouver and twist each side loose.
As for the gaps left behind, you should have some spares bits with the car (depending on whether you have it from new or from the previous owner). These include a couple of rubber sheaths to cover the exposed joint in the rear cage where it was connected to the front cage, and a couple of polestyrene cylinderical plugs to cover the area in the floor where the front cage was.
Hope this makes sense...happy to chat on phone if useful - send a PM in that case.
Here goes...

There are two pieces to the front cage - one is the right side bar (driver's door side) from the floor to where it meets the rear cage - the other includes the left hand side (passenger side) and the cross member running from left to right above the windscreen as one piece.
There are 5 places which need to be unscrewed:
1. Floor bolts at the bottom of each front vertical bar (left and right).
2. Connecting bolts at the top rear where the front cage meets the rear cage (left and right).
3. Top right (above driver's head) where the front cross member meets the right side bar.
Having unscrewed all the bolts in the above 5 places, I find it easier to first release the connecting joint above the driver's head where the left side meets the right side. Once this is loosened, the whole front cage is a little loose and then you have just manouver and twist each side loose.
As for the gaps left behind, you should have some spares bits with the car (depending on whether you have it from new or from the previous owner). These include a couple of rubber sheaths to cover the exposed joint in the rear cage where it was connected to the front cage, and a couple of polestyrene cylinderical plugs to cover the area in the floor where the front cage was.
Hope this makes sense...happy to chat on phone if useful - send a PM in that case.

puntograle said:
Yep - done it before after asking a similar question on here.
Here goes...
There are two pieces to the front cage - one is the right side bar (driver's door side) from the floor to where it meets the rear cage - the other includes the left hand side (passenger side) and the cross member running from left to right above the windscreen as one piece.
There are 5 places which need to be unscrewed:
1. Floor bolts at the bottom of each front vertical bar (left and right).
2. Connecting bolts at the top rear where the front cage meets the rear cage (left and right).
3. Top right (above driver's head) where the front cross member meets the right side bar.
Having unscrewed all the bolts in the above 5 places, I find it easier to first release the connecting joint above the driver's head where the left side meets the right side. Once this is loosened, the whole front cage is a little loose and then you have just manouver and twist each side loose.
As for the gaps left behind, you should have some spares bits with the car (depending on whether you have it from new or from the previous owner). These include a couple of rubber sheaths to cover the exposed joint in the rear cage where it was connected to the front cage, and a couple of polestyrene cylinderical plugs to cover the area in the floor where the front cage was.
Hope this makes sense...happy to chat on phone if useful - send a PM in that case.
Thanks mate, thats very helpful,i'll give it a go this weekend ..i'll PM if i get probs but it sounds straight forward enough.Here goes...

There are two pieces to the front cage - one is the right side bar (driver's door side) from the floor to where it meets the rear cage - the other includes the left hand side (passenger side) and the cross member running from left to right above the windscreen as one piece.
There are 5 places which need to be unscrewed:
1. Floor bolts at the bottom of each front vertical bar (left and right).
2. Connecting bolts at the top rear where the front cage meets the rear cage (left and right).
3. Top right (above driver's head) where the front cross member meets the right side bar.
Having unscrewed all the bolts in the above 5 places, I find it easier to first release the connecting joint above the driver's head where the left side meets the right side. Once this is loosened, the whole front cage is a little loose and then you have just manouver and twist each side loose.
As for the gaps left behind, you should have some spares bits with the car (depending on whether you have it from new or from the previous owner). These include a couple of rubber sheaths to cover the exposed joint in the rear cage where it was connected to the front cage, and a couple of polestyrene cylinderical plugs to cover the area in the floor where the front cage was.
Hope this makes sense...happy to chat on phone if useful - send a PM in that case.

Gassing Station | Porsche General | Top of Page | What's New | My Stuff


