Best route through 996 bulkhead
Discussion
Hi all,
Just thinking about fitting the Dension 500 into my 996T. The kit includes a Bluetooth phone module so I have to get the microphone wire through into the passenger compartment from the luggage compartment. Can anyone share their experience of getting through the bulkhead please? Preferably on the driver's side.
Thanks,
B
Just thinking about fitting the Dension 500 into my 996T. The kit includes a Bluetooth phone module so I have to get the microphone wire through into the passenger compartment from the luggage compartment. Can anyone share their experience of getting through the bulkhead please? Preferably on the driver's side.
Thanks,
B
Why run it to the front lid area? You can fit it under the drivers seat; run the optic cables to the back of the PCM, expansion connectors to the centre console and the associated mic etc is already in the interior, pick up the power from the fuse for CDC player and there is a convenient earth point under the seat too - you may need to bridge the optic at the CDC player if you are making it redundant (you can get an optic bypass plug from BMW if necessary - Porsche don't do them). If you still want to fit it under the front lid: there is a grommet above the clutch pedal - visible under the bonnet trims next to the battery - which was used for the official retrofit of a CDC player but be aware the battery area is a 'wet area' and any badly installed extras can allow water into the cabin; if you intend going through the grommet ensure it's waterproof after.
edit:
If you already have a standard phone module you can pick up the optic and the power directly under the seat instead of running it to the PCM
edit:
If you already have a standard phone module you can pick up the optic and the power directly under the seat instead of running it to the PCM
Edited by Pope on Saturday 17th September 17:02
Easy really remove the plastic battery cover and the plastic panel at the side of it on the drivers side.
Just behind the battery tray at the same height as it on the lefthand corner you will see a rubber blanking plug about 30 mm across,
just put a small slit in it with a stanley knife & your through to the inside.
If yours is a manual this blanking plug will be just behind the clutch pedal if its a tip like mine its dead easy to see.
Feed your wire through to wherever you want, centre console, steering column, etc.
Don't push the grommet out if you can help it cos it's chew to put back on your own.
In my pics you can see a fairly thick loom I put through to drive another amp & head unit.


Just behind the battery tray at the same height as it on the lefthand corner you will see a rubber blanking plug about 30 mm across,
just put a small slit in it with a stanley knife & your through to the inside.
If yours is a manual this blanking plug will be just behind the clutch pedal if its a tip like mine its dead easy to see.
Feed your wire through to wherever you want, centre console, steering column, etc.
Don't push the grommet out if you can help it cos it's chew to put back on your own.
In my pics you can see a fairly thick loom I put through to drive another amp & head unit.
davidlaurel said:
Easy really remove the plastic battery cover and the plastic panel at the side of it on the drivers side.
Just behind the battery tray at the same height as it on the lefthand corner you will see a rubber blanking plug about 30 mm across,
just put a small slit in it with a stanley knife & your through to the inside.
If yours is a manual this blanking plug will be just behind the clutch pedal if its a tip like mine its dead easy to see.
Feed your wire through to wherever you want, centre console, steering column, etc.
Don't push the grommet out if you can help it cos it's chew to put back on your own.
In my pics you can see a fairly thick loom I put through to drive another amp & head unit.


+1 this is how I have gained entry into the front compartment as well.Just behind the battery tray at the same height as it on the lefthand corner you will see a rubber blanking plug about 30 mm across,
just put a small slit in it with a stanley knife & your through to the inside.
If yours is a manual this blanking plug will be just behind the clutch pedal if its a tip like mine its dead easy to see.
Feed your wire through to wherever you want, centre console, steering column, etc.
Don't push the grommet out if you can help it cos it's chew to put back on your own.
In my pics you can see a fairly thick loom I put through to drive another amp & head unit.
Gassing Station | Porsche General | Top of Page | What's New | My Stuff


