Measurements please

[JMF894]

What are the offset/pcd etc etc measurements of a standard 15 inch OZ split rim as found on a 400/450se?

If i were to upgrade to 16 inch wheels how do i need to adjust width/tyre profile etc to compensate for the rolling diameter?

Ideally i'd like a pair of ex Tuscan 16 inch OZ rims for the rear, but i guess they usually come in a set of four.

Cheers Jimbo

[adam quantrill]

I put 16"s in the rear of mine and left the front alone.

A lower profile on the rear brings the rolling diameter back to the same - and is easier to get hold of - I have 245/45/16".

Just watch out for rubbing on the outer wheel arches - I am going to shim up one spring a little.

[voltage_maxx]

PCD (off the top of my head) is 112

[JMF894]

I have rubbing issues on the rear passenger side but...........

I also have some new AVO adjustable dampers on there too. Height adjustable as well as damping/rebound

I think the springs are original and a little tired too

Another winter job lol

Jimbo

[JMF894]

If anyone knows of a pair of 16" Tuscan OZ's ............................

Jimbo

[pwd95]

There were a few sets of these about last year. Managed to get 4 for my old 450SE. Worth ringing around the racers, they might have some on a shelf they don't use any more.

[Mr Tank]

JMF894 said:

If anyone knows of a pair of 16" Tuscan OZ's ............................

Jimbo

Jim

YHM!

Andy

[JMF894]

Mr Tank said:

Jim

YHM!

Andy

Hi Andy, haven't received it yet

Jimbo

[Andy390]

Std 390/400/450 OZ's are 15 x 8 ET 20. some SEACs were 15 x 8 1/2, but not sure of offset.(anyone?)
I've got some StilAuto Alloys i sometimes use on mine, and they're 8 x 16, but ET 15, and they do rub a little on hard cornering (although it does add to dramatic effect!)
HTH
Andy

Edited by Andy390 on Friday 28th October 09:42

[Mr Tank]

JMF894 said:

Hi Andy, haven't received it yet

Jimbo

Jim

Just sent you again, if you don'tnot receive it plaease e-mail me direct:[e-mail]

Andy

[Mr Tank]

Jim

I decided to sell my two 16" OZ rims as they are, today!

Pic below.










They need new tyres and refurbishing due to some marks etc. Included with the wheels is a set of new OZ Racing transfer for the wheels!

I am open to offers!

Andy

[JMF894]

Andy

YHM

Jimbo

[Solitude]

Mr Tank said:

Jim

I decided to sell my two 16" OZ rims as they are, today!

Pic below.










They need new tyres and refurbishing due to some marks etc. Included with the wheels is a set of new OZ Racing transfer for the wheels!

I am open to offers!

Andy

Check they are straight before letting someone drive two hours to come and fetch them won't you Andy !!!

[Mr Tank]

Gavin

They are strait in more ways than one!

Problem is not certain what to charge?

Andy

[JR]

voltage_maxx said:

PCD (off the top of my head) is 112

Yes, it's a 100mm circle with 12mm studs to give a 112PCD. Standard 350 ET is 23. Annoyingly the OZ split rims don't have the size stamped onto the inside. If no one posts I'll try to measure it in the week. Jonathan

[JR]

BTW most head to 245/45/16 at the rear.

[JMF894]

JR said:

BTW most head to 245/45/16 at the rear.

Thanks for that JR
Jimbo